Question about 1990 Toyota Corolla

1 Answer

Remove engine mounts 1990 corolla - 1990 Toyota Corolla

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Toyota Expert
  • 235 Answers

Which ones at the frame on bottom two and there's a exhaust
mount also there in front there's one also you need a hoist long bolt going down center of mount

Posted on Jan 20, 2015

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 651 Answers

SOURCE: Removing Toyota Corolla 1990 Car Stereo

the plastic frame around it should snap out with a flat head screwdriver to get access.

Posted on Dec 19, 2008

  • 1752 Answers

SOURCE: 1990 Toyota Corolla - engine overheating, maybe

Blown head gasket, get it replaced.

Posted on Dec 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace brake light switch for a toyota corolla 1990?


it is normally mounted around the brake pedal area

Dec 28, 2014 | 1990 Toyota Corolla

2 Answers

How to remove radio from 1990 cs corolla


I understand you remove the panel and then for a
1990, it has a handle and you simply pull it straight out.
---
REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. CAUTION
    On models with an airbag, wait at least 90 seconds from the time that the ignition switch is turned to the LOCK position and the battery is disconnected before performing any further work.
  2. Remove the attaching screws from the trim panel.
  3. Remove the trim panel, being careful of the concealed spring clips behind the panel. Remove the trim panel surrounding the stereo 88276p31.jpg

  4. Disconnect the wiring from the switches if so equipped mounted in the trim panel.
  5. Remove the mounting screws from the radio. Remove the four radio retaining screws and pull the unit from the dash 88276p32.jpg

  6. Remove the radio from the dash until the wiring connectors are exposed.
  7. Disconnect the electrical connectors and the antenna cable from the body of the radio and remove the radio from the car. To install:
  8. Reconnect all the wiring and antenna cable first, then place the radio in position within the dash.
  9. Install the attaching screws.
  10. Reconnect the wiring harnesses to the switches if so equipped in the trim panel and make sure the switches if so equipped are secure in the panel.
  11. Install the trim panel (make sure all the spring clips engage) and install the screws. Conmnect the negative battery cable.
  12. Check radio system for proper operation.
prev.gif next.gif

Jul 22, 2010 | 1990 Toyota Corolla

1 Answer

How do you replace front rotors on a 1990 toyota corolla


Remove the tire, next you will have to remove the two bolts holding the caliper on, swing the caliper out of the way, you may need to give the rotor a few taps to lossen, and it should come off fairly easy, make sure the new rotor is the correct size, next using one of the old pads you will need a C clamp to depress the piston to the in postion, after the piston is all the way in, you will snap the new pads into the caliper, now mount the caliper and secure the cailper with the two bolts.

Nov 23, 2009 | 1990 Toyota Corolla

1 Answer

I want to change belt and tensioner at the same time on 05 corolla.


A 19mm wrench to release the tension

A 17mm wrench to remove the main mounting bolt

A 12mm wrench to remove the upper tensioner mount.

BE CAREFUL not to break the main mounting bolt(17mm head) it is a long bolt.

If you break it the engine will have to be removed to extract the broken bolt.

May 21, 2009 | 2005 Toyota Corolla

1 Answer

1990 new yorker alternator replacement


You are right about removing the motor mount. You have to support the engine with a jack. Use a piece of plywood between the jack and the oil pan. Remove the motor mount and you should be able to lift the engine up about 2-3 inches with the jack. Remove the serpentine belt and then you should have enough room to remove the alternator.

Apr 19, 2009 | 1990 Chrysler New Yorker

1 Answer

Removing Toyota Corolla 1990 Car Stereo


the plastic frame around it should snap out with a flat head screwdriver to get access.

Dec 19, 2008 | 1990 Toyota Corolla

2 Answers

Car/1990 Toyota Corolla


If Biggy1 has described it right, I think when you remove the WIRE to the spark plug ( not the plug itself ) and oil jumps out, there is a cylindrical seal that needs replacing and one does not need to even remove the cylinder head.
I have the same problem with my corolla. On the other hand if Biggy meant when removing the SPARK PLUG oil was on the contacts....

Sep 06, 2008 | 1990 Toyota Corolla

Not finding what you are looking for?
1990 Toyota Corolla Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...