Question about 2011 Hyundai ix35 2.0

Open Question

How to change a bulb of the hyundai ix35

The fog lamp bulb

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 566 Answers

SOURCE: 2007 Hyundai Santa Fe - Replacing fog light

hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?

Posted on Oct 28, 2008

  • 67 Answers

SOURCE: Fog Lamp Bulb Replacement, 05 Tucson

remove headlamp assembly and you can get it from the top pretty easy

Posted on Feb 26, 2009

  • 10 Answers

SOURCE: My 2007 Sante Fe fog lamp bulb went out and I wasn't able to

Step:
1. Turn tires away from vehicle
2. There is a plastic covering in front of the wheel that usually goes around the wheel well. There are plastic thumb pins on the outer edges of this plastic covering. Remove the thumb pins and this plastic piece will come off.
3. Behind this you will find access to your fog lights.
4. Remove/Replace just like an ordinary head light.

Posted on Jul 17, 2009

  • 1986 Answers

SOURCE: How do I replace fog lights on my 2002 Hyundai Santa Fe?

Look up into the bumper and see if you can access the fog light. The bulb should just twist out of the back. If not, the assembly should either pop forward or back to come out. I've heard though, that many santa fe's require the removal of the entire front bumper fascia just to get to the bulbs in which case you'd have to remove your headlights to get to the screws holding the bumper fascia on

Posted on Sep 09, 2009

  • 1 Answer

SOURCE: my 4 week old Hyundai ix35's panoramic sunroof

Give me some more information about this problem. May be i can help.

Posted on Jul 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My fog lights won't turn on Nissan sentra GEX 2002


There are several things that can cause your fog lamps to not work. The fog lamp circuits need to be diagnosed. Your entire fog lamp circuit can be tested at the plug for the fog lamp relay located n the relay box.

PIN 5 on the relay should have battery power at all times. This power comes from Fuse #43 (15 Amp) in the fuse and fusible link box in the engine compartment. If there is power at this pin, the fuse and the circuit between the fuse and the relay is good.

PIN 3 on the relay goes to the fog lamp bulbs. There should be continuity to ground through the bulbs on this pin. If you have continuity to ground, connecting a jumper wire between PIN 5 and PIN 3 should make the fog lamps come on unless there is a short circuit to ground, which will cause Fuse #43 to blow. If there is no continuity to ground on this pin, the problem is either that BOTH fog lamp bulbs are burned out or there is a break in the wire between the relay and the bulbs.

PIN 1 Is the battery power for the primary coil in the relay. This power comes from the headlamp switch and power is only supposed to be present here when the headlamps are on and the dimmer switch is on LOW BEAM. If power is not present at this pin, the problem is a bad headlamp switch or an open circuit between the headlamp switch and the relay.

PIN 2 Is the control circuit for the primary relay coil. The control circuit should have continuity to ground when the fog lamp switch is set to the ON position. If there is no continuity to ground with the fog lamp switch on, the problem is a faulty fog lamp switch, an open between the relay and the fog lamp switch, or an open between the fog lamp switch and ground E37 (right front of engine compartment) and ground F7 (left rear of engine compartment) Please note: This circuit has redundant grounds....if one ground is not making good contact, the other ground can still make the circuit work.

PIN 4 on the relay is not used.

If all of the circuits/pins are working as described above, replace the relay.

That is pretty much it... That is all you really need to know to get your fog lamp circuits diagnosed. Let me know if you need further assistance.

May 13, 2012 | 2002 Nissan Sentra

1 Answer

How hard is it to change a fog light bulb on a 2005 Subaru Forester? Can anyone do it?


Front Fog Light Assembly

REMOVAL


  1. Disconnect the ground cable from battery.
105919447



  1. Remove the two clips and lower mudguard on side that bulb is being changed.
  2. Disconnect the harness connector from bulb on back of fog lamp.
105919448




Front Fog Light Bulb

REMOVAL


1. Locate back cover on fog lamp assembly where bulb is located inside.

105919462



  1. Remove the back cover.
105919463



  1. Remove the spring retainer, and then detach the fog light bulb.
  2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.

Jul 27, 2011 | Subaru Forester Cars & Trucks

1 Answer

How to replace a front fog lamp


  • If your fog lamp is connected to or behind a grille, pop it out. This can be done by first removing the clips or screws connecting it to the car and gently pulling it out. (If your fog lights are not connected to a grille, proceed to step 2.)Find the bolts that hold the fog lamp in place; you may have to get underneath the automobile to do so.Using your ratchet wrench, remove the bolts.4Grab the connector on the back of the fog lamp, turn it counter-clockwise and pull it out. This should remove the actual light bulb from the lamp fixture.Remove the fog lamp from the car and place the new one in.6Place the light bulb into the new fog light and turn clockwise to lock into place.Bolt the fog lamp back into place, if you had to remove the grille, put it back now and screw/clip it back into place.Turn on the fog lights and make sure everything is working properly


  • Oct 02, 2010 | 2004 Ford Explorer

    1 Answer

    How to change Ford Explorer fog light


    p, li { white-space: pre-wrap; }

    Open the hood and remove the electrical plug from the back of the fog light ballast below the headlight assembly.



    Turn the fog lamp counterclockwise to unlock it from the fog light housing.



    Insert the new fog lamp. Align the notches on the fog lamp housing with the tabs on the new bulb and turn the bulb clockwise to lock it into the housing.



    Reconnect the fog lamp electrical plug.

    Sep 13, 2010 | 1999 Ford Explorer

    1 Answer

    How do I replace the fog light assembly on a 2000 Olds Alero?


    you replace the fog lamps by going under front bumper fascia.remove the pushpins and take down the splash shield to access the back of the fog lamps.then you remove two bolts retaining the fog lamp to the back of front bumper.besure to wear clean gloves.because fog lamps is halogen bulbs.if you touch with bare hands the oils from hands will make the bulbs over heat and blow out.

    Dec 03, 2009 | 1999 Oldsmobile Alero

    1 Answer

    How do you replace the fog light bulbs on a 2004 buick regal?


    Notes FOG LAMP BULB REPLACEMENT - FRONT

    REMOVAL PROCEDURE
    f98bf40.gif
    1. Remove the front bumper fascia deflector.
    2. Disconnect the electrical connector from the front fog lamp bulb/socket. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
    01c84b0.gif
    1. Rotate the front fog lamp bulb/socket counterclockwise to release.
    2. Remove the fog lamp bulb/socket from the front fog lamp assembly.
    4065803.gif


    1. Install the fog lamp bulb/socket to the fog lamp rotating clockwise until fully seated. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
    b182709.gif
    1. Connect the electrical connector to the front fog lamp bulb/socket.
    2. Install the front bumper fascia deflector.

    Jun 16, 2009 | Buick Regal Cars & Trucks

    1 Answer

    Hyundai Sonata 2003 FOG LIGHTS DONT WORL


    No.. power is supplied to both bulbs in parallell... when power is present at one, it's also present at the other. Clarification needed - have you checked to see if you have power (battery voltage) and ground at the fog lamp connectors?.. if so, the problem is the bulb(s) it/them/self/selves. If you have an ohm meter or a test light, it's a simple procedure. Check the bulbs with an ohm meter. Then using a test light (12 volt, make sure the test light bulb is good by connecting it to a charges 12 v battery) connect the test light bulb to each of the fog lamp connectors with the fog lamp sw turned on and the ignition key in the 'run' position. If the test light illuminates at both fog lamp connectors, then the problem is in the fog lamp bulb(s) themselves. If not, there's a wiring/control circuit problem. You can go to http://www.hmaservice.com/ and register and gain access to lots and lots of technical info about your Sonata.

    May 26, 2009 | Hyundai Sonata Cars & Trucks

    1 Answer

    How to replace a fog lamp with replacement bulb only on 2002 toyota 4runner sport edition???? the three screws on the bottom?


    Well, these are the steps and I will post the pic here in a second...looks like 2 screws...but like I said, you can see the picture for direction on this.


    Remove or disconnect the following:

    Front turn signal lamp
  • Connector
  • 2 screws
  • 2 claw fittings
  • Fog lamp assembly
  • Fog lamp bulb as shown
  • Fog light unit

  • To Install
    1. Install or connect the following:
      • Fog light unit
      • Fog lamp bulb as shown
      • Fog lamp assembly latch the 2 claw fittings and 2 screws
      • Connector
      • Front turn signal lamp
    Trying to post the pics now....

    May 14, 2009 | 2002 Toyota 4Runner

    1 Answer

    Fog Lamp Bulb Replacement


    there are a couple of screws in the front of the fog light that will remove the lense so you can replace the bulb.

    May 11, 2009 | 2004 Chrysler Sebring

    1 Answer

    HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


    ATTN: NIKKICARROLL

    here is how to replace the bulb in your vehicle


    1. Release the hood latch and open the hood.
    2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
    3. Remove the screws holding the headlamp module halves together.
    4. Separate the module halves.
    5. Disengage the wiring from the headlamp bulb.
    6. Remove the retaining ring from the back of the headlamp bulb.
    7. Pull the bulb from the lamp.
    To install:
    1. Push the bulb into the lamp.
    2. Install the retaining ring to hold the bulb in the lamp.
    3. Engage the wire connector to the back of the headlamp bulb.
    4. Place the module into position on the vehicle.
    5. Install the screws to hold the module to the vehicle.
    6. Install the radiator closure panel sight shield.
    7. Check the headlamp alignment and operation.
    88176gb1.gif Exploded view of the fog lamp with the bulb removed
    Click to Enlarge

    1. Release the hood latch and open the hood.
    2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
    3. Remove the screws holding the headlamp module halves together.
    4. Separate the halves.
    5. Remove the fog lamp wire connector cover.
    6. Disconnect the wires from the fog lamp bulb.
    7. Disengage the retainer clip holding the bulb to the fog lamp.
    8. Remove the bulb from the fog lamp.
    To install:
    1. Place the bulb into position in the fog lamp.
    2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
    3. Attach the wire connectors to the fog lamp bulb.
    4. Install the fog lamp wires connector cover.
    5. Place the module halves together.
    6. Install the screws to hold the headlamp module halves together.
    7. Install the radiator closure panel sight shield.
    8. Verify the fog lamp operation and alignment

    ATTN: WDSNEED1

    Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
    Click to Enlarge

    1. Release the hood latch and open the hood.
    2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
    3. Remove the screws holding the headlamp module to the mount adapter.
    4. Separate the headlamp module from the mount adapter.
    5. Disengage the wiring from the headlamp and foglamp.
    6. Remove the headlamp from the vehicle.
    To install:
    1. Attach the wires to the headlamp and foglamp assembly.
    2. Place the headlamp module into position on the mount adapter.
    3. Install the screws to hold the headlamp module to the mount adapter.
    4. Install the radiator closure panel sight shield.
    5. Check the headlamp alignment and operation.

    Jul 28, 2008 | 1994 Chrysler New Yorker

    Not finding what you are looking for?
    2011 Hyundai ix35 2.0 Logo

    Related Topics:

    169 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7772 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...