Question about 2005 Chevrolet Silverado 1500 2WD

1 Answer

What does discard sensor mean b0104 - 2005 Chevrolet Silverado 1500 2WD

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

  • Expert
  • 195 Answers

Airbag sensor malfunction.

Posted on May 23, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Location of the mass flow air sensor in a 2007 Cadillac SRX? how to replace?


Hard to believe you have a bad MAF in a 2007 caddy. How many miles on car? Have you tried cleaning the unit?

Parts store have a locator chart which should show location.

Apr 14, 2015 | 2007 Cadillac SRX

1 Answer

What does error codes: B0100 and B0140 indicate wrong on a 2011 Buick LaCrosse CXL 3.6 V6 eng.?


B0100:
Perform trouble checking for the following: the front end sensor, the SDM module, the SDM wiring harness connector. Damage to the following parts needs replacement or repair. For the DTC B0100, detach the front end sensor1 connector and also detach the SDM connector. Perform trouble checking of the signal and voltage circuits between the SDM and the front end sensor for a short to voltage and for a short to ground. Reconnect all the SIR components and if the DTC B0100 is present then the front end sensor1 has to be changed.
B0104
Perform trouble checking for the following: the front end sensor, the SDM module, the SDM wiring harness connector. Damage to the following parts needs replacement or repair. For the DTC B0104, detach the front end sensor1 connector and also detach the SDM connector. Perform trouble checking of the signal and voltage circuits between the SDM and the front end sensor for a short to voltage and for a short to ground. Reconnect all the SIR components and if the DTC B0104 is present then the front end sensor2/right has to be changed.
i could not find anything on the B0140 code so i included the B0104 incase of typo

May 18, 2014 | 2011 Buick LaCrosse CXL

1 Answer

Sensor problem


Unplug the IAT sensor and look for dirt / grease on the contacts.

Check for damaged wire from IAT to ECU

Discard dirty filter and replace with new.

Jan 18, 2014 | 2008 Renault Megane 2.0

1 Answer

Where the hell can I get a FREE PDF download for my Ford fusion 2 for the removal and replacement of the rear wheel bearings as well as the torque settings for the final nut after replacement.All the so...


Rear Suspension - Rear Wheel Bearing Fusion 2002.75 (06/2002-)

-Removal and Installation

Special Tool(s)

Installer, Differential Bearing
205-062

Installer, Input Shaft Seal
307-210 (17-041)


General Equipment
Soft faced hammerWooden block

Removal

CAUTION: The brake drum and hub assembly removal in this procedure is for installing a new wheel bearing, not for access to brake system components.

-All vehicles

Remove the dust cap.
Remove the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

-Vehicles with rear drum brakes
Release the parking brake.
Remove the brake drum and hub assembly.
Remove and discard the wheel hub retaining nut.


-Vehicles with rear disc brakes
Remove the brake disc.
For additional information, refer to in this section.

Remove the wheel hub.
Remove and discard the wheel hub retaining nut.


-All vehicles

Remove and discard the wheel speed sensor ring (brake disc shown).
Remove the circlip (brake disc shown).
Using the special tool, remove and discard the wheel bearing (brake disc shown).

-Installation

-All vehicles

CAUTION: Support the wheel hub assembly on the wheel mounting face and not on the wheel nut studs.

Using the special tool, install the new wheel bearing (brake disc shown).

Install the circlip (brake disc shown).

CAUTIONS:

Make sure the wheel speed sensor ring is not knocked, damaged and kept free from metal fragments.

Protect the face of the wheel speed sensor ring with a non-ferrous flat block to prevent damage.

Make sure the wheel hub or brake drum is adequately supported and do not allow it to rest on the wheel studs..

Make sure the wheel speed sensor ring is pressed on slowly and squarely until fully seated.

Do not exceed a maximum load of 10 kN.

Using the special tool, install a new wheel speed sensor ring (brake disc shown).

Vehicles with rear drum brakes

CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the brake drum and hub assembly.
Apply the parking brake.

-Vehicles with rear disc brakes


CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the wheel hub retaining nut.
Install the brake disc.
For additional information, refer to in this section.


-All vehicles
Install the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

NOTE: If the dust cap is damaged a new dust cap must be installed.

Using a soft faced hammer and a wooden block, install the dust cap.


There is no real torque settings for the rear wheels, except to say, do not over tighten or you will stretch the lugs and the will loosen over time.

May 28, 2011 | Ford Fusion Cars & Trucks

1 Answer

I am currently changing front pads and think i should pack the wheel bearings but don't know how. its not covered in the haynes manual i got


Here I have the Step by Step :

Wheel and tire assembly Brake caliper and secure it out of the way with a piece of mechanic-s wire. Do not let the caliper hang on the hose. Brake rotor Halfshaft retaining nut and discard it Cotter pin and castellated nut from the tie rod end and separate the tie rod end from the steering knuckle using a suitable removal tool. Discard the cotter pin. Separate the tie rod end from the wheel knuckle ABS sensor bolt and the sensor, if equipped Strut mounting nuts and the studs which attach the strut assembly to the steering knuckle Strut from the steering knuckle Lower ball joint pinch bolt. Carefully pry down on the lower control arm to separate the ball joint stud from the steering knuckle. Wheel hub, knuckle and bearing assembly from the vehicle

Please Rate, Thank you

Aug 13, 2010 | 2000 Ford Escort

1 Answer

My 1994 nisssan maxima does not start what could it be it makes noise to stsrt but it doesn't?


Many issues can cause that: bad fuel pump, bad coils, broken spark plug wires, several sensors like MAF, you should check one by one to discard.

Jan 11, 2010 | 1994 Nissan Maxima

3 Answers

What is the tps and where is the fuel pressure regulator


TPS throttle positioning sensor......Located on the throttle body and looks like this pic attached Top pic is TPS and Other is the regulator



Fuel pressure reg 4.3L Engines
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the upper intake manifold.
  4. Remove the fuel pressure regulator retainer clip.
  5. Twist and pull the fuel pressure regulator in order to remove the regulator from the housing using a shop towel to catch any spilled fuel.
  6. Remove and discard the regulator seal O-ring.
  7. Remove and discard the regulator filter.
  8. Remove and discard the regulator seal O-ring.
  9. Remove and discard the backup ring.
  10. b2da892.jpg

    984e3dd.jpg


Nov 20, 2009 | 2002 Chevrolet S-10

1 Answer

Need to change knock sensor(s)


Locate the sensor ont he side wall of the head. Disconnect the wiring harness and then use a wrench to loosen the sensor. Pull the sensor away from the head and discard. Installation is the reverse. Check these diagrams.

http://www.jimfancher.com/sierra/images/TifToGif1.gif

http://www.jimfancher.com/sierra/images/TifToGif2.gif

Oct 05, 2009 | 2003 GMC Sierra

4 Answers

How do I replace the upper ball joints in my 2002 Ford Explorer?


The upper ball joints are replaceable without replacing the control arms. Use Moog K80008 ball joints and a ball joint press.

Jun 25, 2009 | 2002 Ford Explorer

1 Answer

CTS check engine light code P0451


Hi. the fuel pressure sensor is part of the fuel pump assembly. You will have to remove the fuel pump to replace this. I would go ahead and replace the fuel pump while you are there.You will have to Pull the strainer off the fuel pump and discard it. remove the retaining clip for the fuel pressure regulator so that you can remove the fuel pressure regulator. Disconnect the electrical connections for the fuel pumps and the fuel level sensor. Remove the retaining clip for the fuel level sensor and remove the fuel level sensor by squeezing the locking tangs. the sensor is incorporated in this area.

Please rate and god bless.

Mar 26, 2009 | 2005 Cadillac CTS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...