Question about 2003 Pontiac Montana

Open Question

Wiring diagram for 2003 Pontiac Montana

I have electrical problems

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 55 Answers

SOURCE: replace thermostat 2003 pontiac montana

yes but with the right shaped wrenches and tiny hands it can be done without removing the exhaust crossover pipe

Posted on Oct 16, 2008

Ad
  • 1 Answer

SOURCE: how to put out the radio in montana 2003

there are 4 screws. two in the front behind the cup holder and two up underneath in the cupholder bay after the cupholder is removed. they are phillips head and 8mm I believe. this is all you need to remove the cover.

Posted on Jan 12, 2009

daves944
  • 1050 Answers

SOURCE: 2003 Pontiac Montana Front Wheel Bearings

Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

Posted on Apr 08, 2009

  • 15 Answers

SOURCE: 2003 pontiac montana leaks condensate water in the drivers floor

Bet the drain is clogged with leaves. Look under the blower motor under the hood. Can almost be that the cowling has been filled with leaves at one time or another. Got to clean that stuff out every now and then.

Posted on Jun 20, 2009

1ATony
  • 159 Answers

SOURCE: How do I install a rear wiper motor on 2003 Pontiac Montana?

Here's a great video that will show you how to install the rear wiper motor on a 97-05 Montana or Venture">

Posted on Mar 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What components are in between the ignition switch and the starter?


Get yourself a factory wiring diagram

That is how you learn about electrical circuits

Sep 26, 2014 | 2005 Pontiac Montana

1 Answer

06 montana plug order diagram


Can anyone tell me what is the firing order for a 2006 3.5 Lt; Pontiac Montana

Aug 27, 2012 | 2006 Pontiac Montana SV6

1 Answer

Plus we cant find a wiring diagram for the 2003 pontiac montana minivan


Hi Julia,
Need a wiring diagram for your 2003 blower motor circuits? I would be happy to send them to you. I cannot post them her on the FixYa site due to size and copyright restrictions. If you click on my profile picture, go to my page and click the "pro Services tab Click on any of the services listed (it doesn't matter, you will be connecting with me no matter which one you click) Sign up for email support and I will send you a link to download the diagrams you need.

Oct 22, 2011 | 2003 Pontiac Montana

1 Answer

BACK FIRING, WIRES WERE NOT PUT IN CORRECTLY. I NEED A FIRING DIAGRAM FOR THE 2002 PONTIAC MONTANA


2002 Pontiac Pontiac Montana 3.4 liter V-6 VIN "E"

50c170e.gif

Hope helps (remember rated and comment this).

Jul 15, 2010 | 2002 Pontiac Montana

1 Answer

Replace seats in 2003 Montana with seats from 2000 Montana


I would disconnect the battery minus - cable first, ensure the airbag connectors are the same ! otherwise I do not think you have a problem !!

Aug 11, 2009 | 2003 Pontiac Montana

1 Answer

04 pontiac montana sliding doors no longer work


the sliding doors on montana assuming there power have a electrical harness on the bottom track that break and jam the doors but unlikly both have this problem do the doors lock @ unlock if not check switch at drivers door

May 27, 2009 | 2003 Pontiac Montana

1 Answer

2003 pontiac montana van, when i start the van, i sometimes (not all) get a very loud clicking sound under the hood on the passenger side of the vehicle, and the the van will not start. Other times it...


Bad connection , battery cable bad ect.... voltage drop test .
Starter Voltage Drop
How to voltage drop test starter motor circuit
Looking at a wiring diagram to see what all is involved in the starter electrical circuit for your vehicle .would be a good thing to do. Do you know what a wiring diagram is ? How to read one ? How to use a DVOM- digital volt ohm meter to test automotive electrical circuit's . Free wiring diagram here http://www.bbbind.com/free_tsb.html Enter vehicle info year , make , model an engine size. Under system click engine then under subsystem click on starting . Click the search button then the blue link. Testing the electrical circuit's is the way to find the problem .

Chevy Truck No Start Flickering Lights Gauges Voltage Drop Testing


Jan 18, 2018 | 2003 Pontiac Montana

1 Answer

The tailights on my van don't work the fuse keeps blowing out


i would sell it. only have them test drive it in the daytime, they will never notice.

Apr 25, 2009 | 2003 Pontiac Montana

3 Answers

Brake lights quit working


Tail lights acting insane?

We had the same issue with our 2000 Pontiac Montana. Brake lights, turn signal lights, running lights, back-up lights and emergency flasher didn’t work at all or operated at random. The cause: poorly designed aluminum contacts on the tail light circuit board and wiring harness connector arced over and disintegrated with normal use.

Pull the tail lamp assembly, remove the electrical connector and look for burned contacts on the connector plug and the connector socket (they call this long plastic piece with the socket the circuit board: it includes the four bulb sockets. Replace the circuit board and the wiring connector.

You can DIY this job with basic auto mechanical/electrical skills and tools. The two circuit boards and the two connectors set me back $230 (2009 cost) for new parts. The electrical contacts on the factory replacement parts are improved.

I needed a T-30 torx driver to remove the tail light assembly (you need this to change out bulbs, too), wire cutters, wire strippers, electrical tape and an electrical lug crimper to do the job.

Aug 02, 2008 | 2003 Pontiac Montana

Not finding what you are looking for?
2003 Pontiac Montana Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...