Question about Cars & Trucks

1 Answer

I have a 1990 ford f150 engine is a 351 5.8 liter it's starts good an when I put it in gear it stutters an has no power when pressing on the gas an stalls out

Posted by on

1 Answer

Exhaust Converter Blocked ?

Posted on May 16, 2014

  • Kevin Mayer May 19, 2014

    I haven't checked that yet I put a new fuel filter,fuel regulator ,changed the spark plugs an a air charge temp censor

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: 99 dodge ram 1500 5.2 liter stalling on start up.

Check and clean idle air control valve
check for vacuum leaks
suspect idle air control valve

Posted on Nov 06, 2008

Monster80
  • 460 Answers

SOURCE: what causes engine to hestitate and lose power-get up & go?

It could be a few things..The map sensor,Throttle position sensor,Fuel pump,Mass air flow sensor..

Posted on Mar 31, 2009

  • 532 Answers

SOURCE: 302 engine starts fine but shuts off when put in gear to pull out.

check the idle air bypass solenoid

Posted on May 20, 2009

  • 5 Answers

SOURCE: 1987 F150 rough idle, stalls, smells rich

graphic.aspx?mod=reptiff&module_id=1&session_id=%7b42f14894-9aa8-441f-8d1b-0146757f530d%7d&image_guid=95d12578&print_bw=0&

Posted on Jun 02, 2009

dttech
  • 4803 Answers

SOURCE: f150 died while driving.it will starts but when

If the Engine light is staying on while the engine is running, this is where the diagnosis needs to start. The Engine Control Module needs to be scanned to find out which, of the many systems monitored by the computer is malfunctioning. That system will then have to be properly diagnosed to locate the actual cause of the problem. Only after this, can any effective repairs be made to your vehicle.

Posted on Jan 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 f150 with 351 wont stay running


insufficient battery power to stay running. replace battery or alternator.

Mar 14, 2014 | Ford F-150 Cars & Trucks

1 Answer

1990 FORD F150; 351 WINDSOR 5.8 V8 ENGINE; HAS NEW DISTRIBUTOR COIL AND IGNITION CONTROL MODULE STILL WONT START


crankshaft position sensor is bad. it uses this sensor to tell the computer when to make each plug fire. no signal no fire.

Nov 21, 2013 | 1990 Ford F150

1 Answer

I have a 1990 ford f150 with the 351....i can let it set over night and it will not crank but tries to. i can shoot a little starting fluid in it and it will run but when i give it gas it sounds like its...


if it has a carburettor it may have blocked jets,if so it will need to taken apart & cleaned out & all the jets blown out with compressed air,& may need new gaskets when reassembling.....hope this helps....cheers.

Jul 01, 2011 | 1990 Ford F150

2 Answers

I have a 1990 f150 351 windsor. i am getting fire and gas all the way into the fuel rail but it will not start. If i spray gas into it it will run until the gas is gone. can it be the injectors? if so can...


  • The EEC supplies power to the injectors. So you want to check the EEC relay and see if it is bad. This relay is brown and on the left side of the engine bay. The yellow wire and the red and green wire should have power to them. It's either the relay or a broken power feed wire in the harness. The red wire is the key wire to test for 12 volts with the key on.



ironfist109_122.jpg


Regards, Tony

Jun 04, 2011 | 1990 Ford F150

1 Answer

I have a 1990 f150 351 4x4 runing geers and a f350 460 2x4 cab do the wires mach up


no they don't but id leave the harness connected to engine swap it out and change computer. its not really that complicated. one bolt to undo harness plug from firewall. good luck

Jan 16, 2011 | 1990 Ford F150

2 Answers

Ford F150 engine backfiring, running/idling rough


I Have a 1999 ford f150 4.6 that back fires and is just running really ruff when idling alot of nack fire a sord of like a pulse going on what is my problem?

Apr 16, 2010 | Ford F-150 Cars & Trucks

1 Answer

I have a 1990 Ford F150 4wheel drive pickup; and it is equiped with a straight 6 cyl. engine and an automatic transmission w/overdrive. What years of stock production transmissions will interchange with my...


What you have is an E4OD transmission and will work with all Ford small block engines (300, 302, 351) in F150,F250, F350 and full size Broncos from 1983-1993.

Dec 30, 2009 | 1990 Ford F150

1 Answer

Dual tanks on 1990 Ford F150


It should not cause no problems but instead of removing the tank leave it in the truck take out all the fuel in the tank and jus discontinue use of it. This will save you alot of time and trouble and i also suggest that if anyone besides you drives this vehicle then i would put a locking gas cap on it so it cant be accessed at anytime except by you.

Jun 23, 2009 | 1990 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...