Question about Lincoln MKX

1 Answer

Genie garage door op

How to get remote the truck to open garage door, my two remote open it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 41 Answers

There is a set button on garage door opener look at manual that is in the garage hanging. to make car and door work together you will need both manuals

Posted on May 21, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: remote garage door opener

1-800-355-3515
www.homelink.com

1. Position vehicle within 10 feet of garage door- engine off and battery on.

2. Press/hold 2 outside buttons of Homelink transceiver until red indicator starts flashing rapidly, then release button. This should take about 20 seconds. This erases any previously learned codes.

3. Press/hold remote control and press/hold button of Homelink transceiver simultaneously. Slowly move remote control from 5" away to 1" away from Homelink transceiver. Release both buttons after red indicator starts blinking rapidly. This should take about 5 seconds. I discovered that the Homelink in my TL is a bit faulty because it took much longer to accomplish this than when programming the Homelink in my MDX. My TL's Homelink may "unlearn" it's code in the future and the needed proximity of the TL to the garage door may be much closer than desired until I get the Homelink fixed.

4. Press training button on garage door opener unit until the indicator lights illuminates- this should be immediate.

5. Within 30 seconds press/hold the Homelink button for 2-3 seconds until the red indicator starts flashing rapidly. Repeat a second time. It should now be programmed. Check it by pressing the programmed button on the Homelink receiver.

6. When programming more than 1 garage door opener unit, disconnect power from unit before programming more units. By not doing this the programmed unit could conflict with the unprogrammed units commands.

Problems:

1. The Battery in the garage door remote may be too weak to program Homelink. However, the battery may be strong enough to operate the garage door. One of my remote controls had a weak battery- my system was installed today, fresh out of the box. I had to use the second remote control for the programming of Homelink on my 2 vehicles.

2. Antenna on the garage door opener unit must be hanging down, fully extended.

Posted on Dec 08, 2008

op212148
  • 46 Answers

SOURCE: remote garage door

drive away from your house and find a place to park. Take your garage door opener and hold it up by the openers on you van . Press the button that you want to operate you garage door and the original opener at the same time it should flash 2 or three times . Now you should be able to use the one that came with the car. (note: it will depend on the age of you garage door opener)

Posted on Mar 23, 2009

swolfinor
  • 504 Answers

SOURCE: How do I program my Genie garage door opener to my 2005 Kia

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Posted on May 26, 2010

swolfinor
  • 504 Answers

SOURCE: Programming car remote using garage door opener remote control fo

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Posted on May 26, 2010

swolfinor
  • 504 Answers

SOURCE: Hummer H3 ReProgram Garage Door Opener forOLD Genie

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2012 hyundai tucson setting the garage door opener that is located in rear view mirror


Thanks filter4991;
1. Press and hold button on car's rearview mirror
2. Press and hold button on garage door opener's remote control.
3. Light on Rearview mirror will flash rapidly.
4. Release both buttons.
5. Locate learning button on garage door opener (generally this can be found by tracing the antennae to where it is attached to the unit.)
6. Press and release "Learning button"
7. Press and release rearview mirror button repeatedly until garage door opens/closes but it should work the first or second time.

Worked on Genie Intellicode and Hyundai Tuscon

Sep 20, 2012 | Hyundai Tucson Cars & Trucks

1 Answer

We want to erase all of the programed instructions for the garage door in our Chrysler 2002 mini van the book says to push the 2 outside buttons until the green light begins to flash we don't know...


I just installed a garage door opener and the programming is done on it, not in the car. There is a button you push on the opener that learns your code and then remembers it. If you have an owner's manual for your opener, check in there. On mine, which is a Genie, you open the lower part of the cowl and there is a button you push and hold in until it starts blinking. Then within 30 seconds you have to push your opener remote or your in-car transmitter and it will learn the code.

Dec 19, 2010 | 2002 Chrysler Town & Country

1 Answer

Trying to program car to open garage. I own a 2008 Sequioa. The garage door company is Genie.


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Jan 05, 2010 | 2006 Toyota Sequoia

1 Answer

How do I program my Genie garage door opener to my 2005 Kia


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Oct 16, 2009 | 2005 Kia Sorento

2 Answers

How do I program my Jaguar XJR garage door opener?


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Jun 30, 2009 | 2006 Jaguar XJ8

1 Answer

Homelink garage door opener will only work at very close range - i.e. whent he garage door is open or when the car is in the garage to open to garage door. Is there as RF sensor that could be obscured?


UNPLUG EVERYTHING NEAR THE GARAGE EXCEPT THE OPENER IF THAT HELPS PLUG THEM IN ONE AT A TIME UNTIL YOU FIND THE PROBLEM.
PROBABLY RF COMING FROM SOMETHING IN THE GARAGE, FREEZER, BATTERY CHARGER (IN AN RV OR MOTORCYCLE)
OR A LIGHT TRANSFORMER - EVEN ANOTHER DOOR OPENER CAN CAUSE PROBLEMS - YOU DIDN'T LIST THE BRAND OF OPENER, GENIE HAS REPLACEMENT RECIEVERS IF YOU HAVE MORE THAN ONE UNIT IN A GARAGE.
HOPE THIS HELPS

Jun 07, 2009 | 2002 Lexus ES 300

1 Answer

Hummer H3 ReProgram Garage Door Opener forOLD Genie


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Jun 02, 2009 | 2007 Hummer H3X

1 Answer

GARAGE CONTROL SYSTEM


Try holding the hand held remote up next to the homelink (built in remote). Hold down the botton on the hand held remote and the botton you want to program in the car at the same time until the homelink light goes out. This could take 60 seconds or more. Now depending on which model garage door open and how old it is you may need to program the car to the opener. Usually this is done by pushing the botton on the back(Liftmaster,Sears, Chamberlin) or the botton on the front(Genie) and then go to the car and push the same botton on more time. I hope this helps.

Feb 05, 2009 | 2005 Honda Pilot

1 Answer

Programming the garage door opener


Homelink Garage Door Opener Programming Procedure:

The procedure described below was successfully applied to a 2005 Jaguar S-Type.

To begin with, several attempts were made using the programming instructions contained in my Jaguars owners manual. Though the procedure described in the owners manual was straight-forward and understandable, I was unsuccessful in getting the vehicles remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the Rolling Code feature.

To begin with, be sure to clear previous codes on your Jaguars garage door opener by first turning (rotating) the ignition key to the I position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle buttons red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguars garage door opener console buttons. Choose which button on your Jaguars remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguars opener button. The red light on your Jaguars center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.

Part two: Now it is time to utilize the Learn function on your Genie garage door opener. Press the Learn button on your Genie garage door opener. The red LED adjacent to the Learn button will begin to flash. You now have 30 seconds in which to program your Jaguars opener button. Using the same button you just used in the part 1 procedure, press and hold the same button for several seconds. As before, your Jaguars red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center buttons red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguars remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguars remote button confirms to the Genies rolling code that your Jaguars signal is legitimate and is to be trusted from then on.

Jun 06, 2008 | 2003 Jaguar XJ-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...