Question about 2002 GMC Envoy XL

1 Answer

Hoe do I release belt tansioner and what tool do I need

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 28 Answers

Posted for another similar question I aswered:
There is usally and idler wheel that the fan belt goes around that you have to push away from the belt with a socket wrench or a special tool you can buy at most auto stores (a long bar with the proper drive on the end of it) it inserts usaully dead center of the idler. Sometimes I just use a crow bar pressing againt the idler pulley if there is something safe to press agaist. Sometime you have to losen the alternator bolts and tip the alternator away from the belt if it runs of the same belt as the fan.

Posted on Jun 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hoe to change the timing belt


Are you sure you're not referencing the serpentine belt? According to manufacturer's specifications, there are chains only.

Mar 27, 2014 | 2003 Suzuki Aerio

1 Answer

How to change serpentine belt on rav4 2004 model


You'll need to buy a tensioner release tool to do the job. Any auto parts store sells them. Use the tool to release the tension by moving the pulley enough to get the belt off . Route the new belt around all the pulleys on the engine according to the diagram sticker under the hood.once you're ready to put tension on the new belt, move the pulley again and put the belt under the pulley. Release the tool and you're done.

Feb 19, 2013 | 2004 Toyota RAV4

1 Answer

Change the belt


need to take tension off spring loaded pulley with tool sometimes a bolt sometimes a square hole, find tool at parts store , follow diagram near hood latch for belt routing, release tension remove old , install new release tension , good to go

Mar 15, 2011 | 2000 Dodge Durango

1 Answer

Cant get the release for the serpentine belt to release


I have a 91 dynasty a 3.3l I just change the serpentine belt you need to buy a tool serpentine belt tool kit from harbor feight tools item # 66344 I bought mines on sale for $16.99. And also
make sure you got the right belt size for your car it list three belts
that will fit because my car was built before feb.17 1991. I was giving two wrong belts before I got the right one talk about hell on earth. had to change my alternator water pump that was the easy part.
I hope this help
:) Wil

Dec 28, 2010 | 1991 Dodge Dynasty

1 Answer

How do you replace the serpintine belt on a 1998 contour?


Open the hood and locate the belt tensioner. The serpentine belt drive is located on the front of the engine on the passenger side of the engine compartment. The spring-loaded belt tensioner on the 1998 Contour is located slightly to the left of and below the water pump pulley
Release the tension on the belt using the serpentine belt removal tool. On vehicles equipped with the 2.5 liter V-6 engine, snap the 3/8 inch-drive adapter onto the removal tool. Slip the tool into the square, 3/8-inch hole in the end of the tensioner arm. Rotate the tensioner clockwise to release the tension. While holding the tensioner back, remove the belt from one of the pulleys. Release the tensioner, remove the belt from the remaining pulleys and pull it out of the engine compartment
Snap a13 mm socket adapter into the belt removal tool for the 2.0 liter, four cylinder Contour. Place the tool onto the 13 mm bolt that holds the tensioner pulley to the tensioner arm and rotate the tensioner clockwise. While hold the tensioner back, slip the belt off one of the pulleys. Release the tensioner, slip the belt from the remaining pulleys then remove it from the engine compartment
Route the new belt around the pulleys, according to the belt routing guide. The belt routing guide on the 1998 Contour is located on a decal on the left (passenger side) strut tower. If this decal is missing, or unreadable, the belt routing guide can also be found in your service manual. Rotate the tensioner pulley one more turn to allow the new belt to slip under the tensioner pulley.
Check the belt for proper alignment on the pulleys. It should lay flat on the pulley and not overhang the edges. If the belt must be repositioned, release the tensioner and reposition as needed.

Sep 18, 2010 | 1998 Ford Contour

1 Answer

How to put on the belt?


If it's a serpentine belt

Go to autozone

Rent a serpentine belt remover tool for free

Release tension on the belt tensioner, remove belt

Install new belt

Release the belt tensioner from the tool and you are done.

Mar 31, 2010 | 1997 Ford Escort

1 Answer

How do i loosen the auto tensioner on my 02 civic si


2002 Honda Civic SI 2.0L MFI VTEC DOHC 4cyl
  1. Place a long-handled, boxed-end wrench or a belt tension release tool (A) on the drive belt auto-tensioner from above the engine. Slowly turn the wrench in the direction shown to release the tension, then remove the drive belt.
    WARNING This is a hydraulic type auto-tensioner; you must turn the wrench slowly.
  2. Install the new belt in the reverse order of removal.
9d15e8d.jpg

Fig. Removing the serpentine belt-2006 Civic with 2.0L engine shown

47af0c8.jpg


Fig. Move the auto tensioner (A) to remove the serpentine belt (B)-S2000

477996f.jpg

Fig. Move the auto-tensioner (A) using the belt tension release tool to relieve tension from the drive belt (B), and remove the drive belt-Accord with 2.4L engine

af364c4.jpg

Fig. Move the auto-tensioner (A) using the belt tension release tool to relieve tension from the drive belt (B), then remove the drive belt-Accord with 3.0L engine

I hope helps with this. Good luck.

Dec 29, 2009 | 2002 Honda Civic

1 Answer

Replace fuel filter in 2003 4.6 eb expedition


the fuel filter should be on inside of left frame rail midway on truck. will need special tool to release the lines. spray with wd-40 to help remove. could be rusty

Nov 30, 2008 | 2003 Ford Expedition

1 Answer

2002 taurus wagon


will need a special tool for job.(belt tensioner pulley tool)
release tension with tool on belt tensioner.then remove old sepentine belt,then install new belt using same method

Jun 04, 2008 | 2002 Ford Taurus

Not finding what you are looking for?
2002 GMC Envoy XL Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...