Question about 2004 Nissan Maxima

1 Answer

Cam shaft sensor picture diagram for 2004 maxima

Posted by on

1 Answer

Google the question,that's all that is needed to find it

You can go to You Tube Video & maybe watch something
about that sensor being tested or replace & why

Posted on Jun 13, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

daves944
  • 1050 Answers

SOURCE: timimg for a 1990 nissan maxima

If your belt came with marks, then they should match the marks that are on the sprockets and block, if not, you must have the cam marks align with those on the engine. If you're in doubt about the exact spot, lay a tooth pick across the sprockets so that you can check alignment to the block.

Posted on Apr 12, 2009

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Posted on Jul 01, 2009

  • 145 Answers

SOURCE: where is the cam position sensor located on a 2004

Here is 7353049.jpg

Posted on Jul 02, 2009

emissionwiz
  • 75822 Answers

SOURCE: how to replace cam sensor in 2004 nissan maxima

the sensor is under the intake manifold, this must be removed to access it.

Posted on May 18, 2010

  • 56 Answers

SOURCE: Hello, Where is the Cam

3.5litre V6 Front wheel drive, the cam position sensor is in the back of the cylinder head above the transmission. bank one is the front bank, nearest to the grill. the cam sensor is held into the head with a 10mm bolt, has one wireing connector with 3 wires in it. the sensor is sort of round with a leg off one side for the bolt the secure.
may need to remove the engine cover to see it. it is held down with allen key bolts.

Posted on Mar 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is a picture for a cam shaft sensor fo 2004 maxima


If you have a 3.5 engine there are two cam shaft sensors(one for each cam)As you look at the engine they are at the right end of the engine,at the end of the cam shafts.They tend to go at the same time,or close to one another so replace both while you are at it.They are held in place with one bolt.Go to the auto store and get the new ones and it will make your job a little easier. good luck

May 16, 2014 | 2004 Nissan Maxima

1 Answer

How to replace a camshaft sensor on 2004 nissan maxima SE




Hi, this cars cam sensors are easy to change. One on the right side and one on the left side of the motor.

  • See my diagram for a visual


  1. Remove the mounting bolt.
  2. Remover the connector
  3. Remove the sensor
  4. Install new sensor.
  5. Reverse to complete.
  6. Same for the sensor on the other side.







ironfist109_99.png
ironfist109_350.jpg



  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 09, 2011 | 2004 Nissan Maxima

1 Answer

Where is the rear bank camshaft position sensor located on a 2004 Nissan Maxima DOHC 6 cylinder?


Both cam sensors are on the rear of the cylinder heads. They are located in the same place on each head. The only difference in the two sensors is one has a straight connector and the other has an angled connector because of other things that are in the way, (see diagram)


dttech_172.gif

Aug 22, 2011 | 2004 Nissan Maxima

2 Answers

What does the cam censor control on a Nissan 2004 Maxima and where is it located?


where is the crank shaft sensor located on 2004 nissan maxima 3,5sl

Apr 13, 2010 | 2004 Nissan Maxima

4 Answers

Transmission stuck in 5th gear???


This is most likely one of your cam shaft sensors. The reason your transmission goes to 5th gear and stays there is because the car automatically goes into "safe mode". This prevents you from running the car on high RPM's which decreases the chance of causing more damage to the engine.
Depending on the code you get from the check engine light, it will be one of the cam-shaft sensors or the crank shaft sensor. A code reader will answer that question.
Often the sensor just fails or oil gets into the connectors which prevents proper reading. This sometimes goes away temporarily when engine is hot but problem will return.
To replace the cam shaft sensors you are looking at approximately 30 min of work. Its a tight fit but not a difficult job.
Cam shaft sensors are about $80. Not sure how much crank haft sensor is.
Hope this helps, and good luck.

May 27, 2009 | 2004 Nissan Maxima

1 Answer

My 2004 Maxima SE cuts off while driving


Might be one of the cam shaft sensors.

Mar 12, 2009 | 2004 Nissan Maxima

Not finding what you are looking for?
2004 Nissan Maxima Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...