Question about 2004 BMW 3 Series

Open Question

Winshield washer failure - 2004 BMW 3 Series

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Winshield washer quit


Check and tighten the engine firewall connector that all cab wiring exits through. I suggest you loosen the large connector and then reinsert, it may have water intrusion.

Oct 06, 2016 | 2000 Ford Ranger SuperCab

1 Answer

Winshield warning light is on in the information center


I have the same jeep it is the washer fluid level. you need washer fluid

Oct 28, 2012 | 1997 Jeep Grand Cherokee

1 Answer

How to replace the winshield washer fluid resevoir 2001 pontiac grand am 3.6L


  1. Remove the left front fender liner.
  2. Remove the air intake duct.
  3. Remove the connector from the washer pump.
  4. Remove the hose from the washer pump.
  5. Remove the connector from the level sensor.
  6. Remove the brake control module.
  7. Remove 3 screws and the washer solvent container from the vehicle.

    Reverse to install.

Oct 17, 2012 | 2001 Pontiac Grand Am SE

1 Answer

2011 Toyota Camry winshield washer fluid light on dashboard won't turn off after filling tank.


The sensor inside the tank is defective or covered in goo. Remove the sensor from the tank or remove the tank and flush it clean with hot water and a mild solution of white vinegar, if the sensor still reads the tank is low replace it.

Sep 25, 2012 | 2011 Toyota Camry

2 Answers

Winshield washer on 2011 nissian rouge stoped working, why?


look at the bottom of the washer tank there should be a round cylinder with a plug with 2 wires on it. unplug it and use a 12 volt meter 1 wire to 1 side of the plug and the other wire on the meter to the other side of the plug. once this is done look at the meter and have someone press the washer fluid button in the car. you should have 12 volts. if not start checking fuses

Aug 20, 2012 | Nissan Rogue Cars & Trucks

1 Answer

My wiper fluid wont come out


Check and verify that you indeed have the winshield washer tank filled if the tank is filled make sure the winshield washer hoses are attached to the washer nozzles under the hood if all of this checks out you probably have a bad windshield washer pump...

Dec 07, 2010 | 2004 Honda Civic

1 Answer

CAn't find the winshield washer bottle. Where is it located?


look at your car manual, if u don't have one look
under your hood neer the left or right fender for a blue plastic cap.

gl G

May 03, 2009 | Toyota RAV4 Cars & Trucks

2 Answers

Winshield washer fluid


Sometimes they have a port in the back along the inside behind an access panel. Others have a seperate washer fluid tank in the motor compartment. See if there is an access panel behind the rear seat on either side.

Dec 10, 2008 | 2000 Dodge Caravan

1 Answer

Winshield washer motor does not run


These days, most windshield washer pumps are mounted to the bottom of the washer fluid reservoir. Where’s that, you ask? Well, inner+fender+w+text.jpgyou know that spout you pour the fluid into—the one that disappears into nowhere? Well, the reservoir is actually 2384f71.jpglocated inside the front fender between the bumper and the front wheel. To replace the pump, you will have to jack up the vehicle, remove the front wheel and then remove the inner fender liner.

Jun 08, 2008 | 2001 Honda Civic

Not finding what you are looking for?
2004 BMW 3 Series Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...