Question about 2008 Chrysler Aspen

1 Answer

Removing rear wheel studs

Rear parking brake assembly and backing plate are in the way of removing wheel lug studs.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 63 Answers

There should be one spot while turning rear wheel bearing that will allow one stud to be knocked out and new stud replaced BEFORE trying to remove the next stud... one at a time

Posted on May 18, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: rear brakes lock up

ABS hydraulics on that unit are a known problem.

The dealer has a set of gauges to install and verify.

Shop around for prices on one, including salvage, then take it to the dealer to verify the concern before you shell out a couple hundred bucks.

Its not a tough replacement if you are handy with a wrench.

If not, leave that one to the pros.

Posted on Sep 01, 2008

davidsspa572
  • 51 Answers

SOURCE: wheel studs or bolts

Hello Miguel Thank you for using FixYa.com my name is David I hope this Helps you out.
Studs often get damaged from overtightening or from cross threading a nut on the threads. A damaged stud is replaced by unscrewing it from the part and installing a new one of the exact same size.
Stud replacement can be difficult because the stud has often been in place for a long period of time. There has been constant heating and cooling, corrosion, and rust buildup between the stud threads and the internal threads of the part. These factors combine to make some studs very difficult to remove.
The first step in stud removal is to use penetrating fluid to remove the corrosion to free the stud from its mating threads. Soak the area of the threads with penetrating fluid. Allowing the fluid to soak into the threads overnight will make it easier to remove the stud.
Before removing the old stud, measure the distance it sticks up from the surface. This measurement will be needed later when installing the new stud. Use a 6-inch scale to measure from the part surface to the top of the stud. Write the measurement down so it can be referred to later.
A stud remove is used to remove studs. It is installed over the stud. The jaws on the stud remover grip the outside of the stud. A wrench fits on the stud remover and allows the technician to rotate the stud in a counterclockwise direction to remove the stud.
If a stud remover is not available, a stud can be removed with two nuts. Locate two nuts that are the correct thread size. To thread onto the stud. Start one nut and thread it all the way down to the bottom of the stud. This nut will be the drive nut. Start another nut and thread it down until it contacts the first nut. This is called the jam nut.
Put a wrench on the bottom drive nut and hold it in place. Put another wrench on the jam nut and tighten, or "jam" it against the drive nut. The jam nut will now hold the drive nut in position on the stud.
Now put an open-end wrench on the bottom drive nut. Turn the nut in a counterclockwise direction. Turning the nut in this direction causes it to want to unscrew the stud. Instead the forces cause the stud to unscrew.
When the old stud is out, inspect the internal thread. If it appears rusty or damaged, clean up the thread by running the correct size tap through the threads as previously explained. Compare the new stud with the old one. The studs should be exactly the same thread size and the same length.
Check the vehicle's service manual to determine if the threads of the new stud should be coated. If the stud should be locked in place and not easily removed, you may need to use a threadlocking compound or threadsealing compound. Threadlocking compounds are on studs and other fasteners when vibration might cause them to unscrew. Thread sealants are used when a stud extends where liquids, such as oil or coolant, could get on the fastener.
Antiseize compound is used on the stud threads to prevent the stud from reacting with the metal on the internal threads. If this happens, the stud could stick or seize. Antiseize compound prevents this reaction and makes the stud easier to remove the next time.
After the new stud is properly coated, it can be installed. Start the stud by hand, making sure it enters the threads securely. Turn the stud in as far as possible by hand before using any tools. Then use two nuts as described earlier to drive the stud into the part. Use the depth measurement made on the old stud to be sure it is driven in the correct depth.

upper_left.gif grey_line.gif upper_right.gif grey_line.gif Look for More Parts A B C D E F G H I
J K L M N O P Q R
S T U V W X Y Z grey_line.gif lower_left.gif grey_line.gif lower_right.gif Related Parts: grey_line.gif 0900823d80050bfd.gif Wheel Nut

Posted on Nov 06, 2008

  • 154 Answers

SOURCE: Adjusting Padking Brake with 4 wheel disc brakes.

Hope this helps. This is out of the factory manual. Let me know if this works for you.
PARKING BRAKE NOTE: Tensioner adjustment is only necessary when the tensioner, or a cable has been replaced or disconnected for service. When adjustment is necessary, perform adjustment only as described in the following procedure. This is necessary to avoid faulty park brake operation.

  1. Raise vehicle.
  2. Fully back off cable tensioner adjusting nut at equalizer to create slack in cables.
  3. Remove rear wheel/tire assemblies. Remove brake calipers and rotors.
  4. Verify park brakes are in good condition and operating properly.
  5. Verify park brake cables operate freely and are not binding, or seized.
  6. Check park brake shoe adjustment.
  7. Reinstall rotors and make sure rotors turn freely.
  8. Reinstall brake calipers. Tighten guide pin bolts to 41 n·m (30 ft.lbs.)
  9. Reinstall wheel/tire assemblies after brake shoe adjustment is complete.
  10. Lower vehicle enough for access to park brake foot pedal. Fully apply park brakes
NOTE: Leave park brakes applied until adjustment is complete.
  1. Raise vehicle again.
  2. Mark tensioner rod 6.35 mm (1/4 in.) from edge of tensioner bracket Adjustment Mark On Cable Tensioner Rod
  3. Tighten adjusting nut at equalizer until mark on tensioner rod moves into alignment with tensioner bracket
CAUTION: Do not loosen, or tighten the tensioner adjusting nut for any reason after completing adjustment.
  1. Lower vehicle until rear wheels are 15-20 cm (6-8 in.) off shop floor.
  2. Release park brake foot pedal and verify that rear wheels rotate freely without drag. Verify pedal returns to fully released position.
  3. Lower the vehicle

Posted on Apr 03, 2009

martin538
  • 117 Answers

SOURCE: rear disc removal. Chrysler Grand Voyager

You need to de adjust the handbrake shoes through the small inspection cover on the back plates. Slackening off the parkbrake cable may help as well.

Posted on Apr 08, 2009

  • 5537 Answers

SOURCE: how to replace lug studs on 2002 chrysler town

I'll try to help you. If you are having trouble with 3 out of 5 studs on one wheel you may want to go to an autoparts store or Salvage yard to look at the whole hub. Usually a press is used to remove the bolts so you would be taking off the hub anyway. When you pay for 3 bolts and labor you may be better off in a Salvage yard or parts place for a different hub. The rear hub on front wheel drive cars is like a trailer axle. Much simpler to remove mounting bolts and press in new bolt. But if rear has differential(rear wheel drive) it has an axle shaft. Would be easier to grind and drill out broken stud on car. You can draw new bolt into place by placing bolt through a socket and use the wheel nut to draw the bolt into the hub.

Posted on Jul 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear bearing


Remove the rear wheel, if the vehicle has rear disc brakes remove the brake caliper and brake rotor, If the vehicle has drum brakes , slide the drum off. Remove the 4 hub mounting bolts located on the back side of the backing plate.Using a hammer tap on the hub assembly (near the wheel studs) Reverse the steps to install the new hub assembly.

Jun 11, 2013 | Cars & Trucks

1 Answer

Replace rear breaks


Rear Drum Brakes-let me know if you have rear disc brakes. Brake Drums Removal & Installation Remove the access hole plug, then back off the adjusting screw 88009g07.gif
Exploded view of the drum brake system 88009g06.gif

  1. Raise and safely support the vehicle with jackstands.
  2. Mark the relationship of the wheel to the axle flange to help maintain wheel balance after assembly.
  3. Remove the tire and wheel assembly.
  4. Mark the relationship of the brake drum to the axle flange. CAUTION
    Do not pry against the splash shield that surrounds the backing plate in an attempt to free the drum. This will bend the splash shield.
  5. If difficulty is encountered in removing the brake drum, the following steps may be of assistance.
    • Make sure the parking brake is released.
    • Back off the parking brake cable adjustment.
    • Remove the access hole plug from the backing plate.
    • Using a screwdriver, back off the adjusting screw.
    • Install the access hole plug to prevent dirt or contamination from entering the drum brake assembly.
    • Use a small amount of penetrating oil applied around the brake drum pilot hole.
    • Carefully remove the brake drum from the vehicle.
  6. After removing the brake drum it should be checked for the following:
    • Inspecting for cracks and deep grooves.
    • Inspect for out of round and taper.
    • Inspecting for hot spots (black in color).
To Install:
  1. Install the brake drum onto the vehicle aligning the reference marks on the axle flange.
  2. Install the tire and wheel assembly and hand-tighten the lug nuts.
  3. Carefully lower the vehicle, then tighten the lug nuts to 100 ft. lbs. (140 Nm).
  4. Road test the vehicle.
prev.gif next.gif

Feb 14, 2011 | 1998 Chevrolet Lumina

1 Answer

How to get drum pads off a 2000 dodge caravan


The pad drums of your 2000 Dodge Grand Caravan can wear with use. Heat buildup in the brakes can glaze, warp or crack the drum. If that happens, replacement of the drum is the only way to fix it. In most cases, you can remove the rear drums, replace them with a new set and leave the existing shoes on the van. Take a minute and inspect the brake shoes thoroughly while you have the drums off the van.


  1. Loosen the lug nuts on the rear of your 2000 Dodge Grand Caravan with a lug wrench. Do not take them off the wheel studs.
  2. Raise the rear of the van with a jack and support it on a set of jack stands. Place the stands under the rear suspension, making sure they are secure. Remove the lug nuts from the wheel studs and pull off the rear wheels.
  3. Check the rear drum where the wheel studs come through for retaining clips. These are used during the manufacturing process; and if they are still on your van, they need to be removed. Pry the clip off the wheel stud with a flat head screwdriver and discard them. Most vehicles will have two clips on each brake drum.
  4. Grasp the brake drum on the outer edges and pull it straight off the wheel studs and brake pads. Discard the old drum and slide the new drum into place, aligning the holes in the drum with the wheel studs. Push the drum in until it seats completely. Repeat the process on the opposite side of the van.
  5. Position the wheel back on the wheel studs and install the lug nuts by hand. Raise the back of the van with a jack and remove the jack stands from under the suspension. Lower the van to the ground and tighten the lug nuts with a lug wrench.

Jan 08, 2011 | 2000 Dodge Caravan

1 Answer

I need a diagram of the rear brakes of a 1997 Intrepid Chrysler-where can I get one>


If the following is not enough then maybe try Alldata.com which generally has more information, but it will cost: REMOVAL & INSTALLATION Chrysler Concorde, New Yorker, LHS Dodge Intrepid Eagle Vision
  1. Remove the rear wheels and brake drums.
  2. Remove the dust cap from the rear hub and bearing assembly.
  3. Remove the cotter pin, nut retainer and wave washer. Discard the old cotter pin.
  4. Remove the rear hub and bearing assembly retainer nut and washer. Remove the rear hub and bearing assembly from the spindle.
  5. Remove the automatic adjuster spring from the adjuster lever.
  6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
  7. Disconnect the parking brake cable from the actuating lever. Disconnect parking brake cable one side at a time.
  8. Remove the both lower brake shoe to anchor springs.
  9. Remove the 2 brake shoe hold-down springs from the brake shoes.
  10. Remove the brake shoes, upper shoe-to-shoe return spring, automatic adjuster and automatic adjuster lever from the backing plate as an assembly.
  11. Separate the brake shoes from the automatic adjuster mechanism.
  12. Remove the brake shoe automatic adjuster lever from the leading brake shoe. To install:
  13. Thoroughly clean and dry the backing plate. To prepare the backing plate, lubricate the bosses, anchor pin and parking brake actuating lever pivot surface lightly with lithium based grease.
  14. Remove, clean and dry all parts still on the old shoes. Lubricate the starwheel shaft threads with anti-seize lubricant.
  15. Assemble both brake shoes, the top shoe to shoe return spring, automatic adjuster and automatic adjuster lever before mounting on vehicle. Make sure the ends of the automatic adjusters are positioned above the extruded pins in the webbing of the brake shoes prior to installation.
  16. Install the brake shoe assembly onto the brake support plate and install the hold-down springs.
  17. Install the lower anchor springs and reconnect the parking brake cable to the park brake lever of the trailing brake shoe.
  18. Rotate the serrated adjuster nut to remove the free-play from the adjuster assembly.
  19. Install the automatic adjuster lever spring on the lead brake shoe assembly and the automatic adjuster lever.
  20. Install the rear hub and bearing assembly. Install washer and retainer nut and torque to 124 ft. lbs. (168 Nm).
  21. Install the wave washer, nut retainer and a new cotter pin onto the spindle. Install dust cap.
  22. Adjust brake shoes so not to interfere with brake drum installation. Install the rear brake drum. NOTE: After installing the brake drums, pump the brake pedal several times to partially adjust the brake shoes. To verify proper operation of the self-adjusting parking brake, be sure that both rear brakes are not dragging when the parking brake pedal is released.
  23. Install the rear wheels and lug nuts. Torque the lug nuts, in a star pattern sequence, to 95 ft. lbs. (129 Nm).
  24. Road test the vehicle. The automatic adjusters will continue brake adjustment during the road test of the vehicle.
prev.gif next.gif

Sep 03, 2010 | 1997 Dodge Intrepid

1 Answer

How to disassemble the rear end in a 2000 gmc yukon and how to remove axles


Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Loosen the lug nuts on the wheel and tire assemblies but do not remove the lug nuts
  3. Raise and support the vehicle
  4. Remove or disconnect the following:
    • Wheel and tire assemblies
    • Axle lubricant into a suitable container
    • Rear driveshaft
    • Parking brake cable
    • Brake calipers
    • Shock absorbers from the axle brackets
    • Vent hose from the rear axle vent fitting
    • Nuts and the washers from the U-bolts
    • U-bolts, spring plates and spacers from the axle assembly
  5. Lower the axle assembly from the vehicle
To Install:
  1. Place the rear axle assembly under the vehicle
  2. Align the rear axle assembly with the springs then connect the spacers, spring plates and the U-bolts to the rear axle
  3. Raise the rear axle assembly into position
  4. Install or connect the following:
    • Washers and nuts to the U-bolts; Torque to: 59 lb-ft. (80 Nm) then, Torque to: 89 lb-ft. (120 Nm)
    • Vent hose to the rear axle vent fitting
    • Shock absorbers to the rear axle
    • Brake calipers (See: Brake Caliper)
    • Parking brake cable (See: Parking Brake Cable)
    • Rear driveshaft (See: Rear Driveshaft)
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  5. Fill the rear axle with lubricant
  6. Bleed the brake system (See: Brake Bleeding)
  7. Install the wheel and tire assemblies
  8. Lower the vehicle to the ground
  9. Torque lug nuts as follows:
    • Single Wheel: Torque to: 140 lb-ft. (190 Nm)
    • Dual Wheel: Torque to: 175 lb-ft. (240 Nm)
  10. Road test the vehicle to check performance
prev.gif next.gif

Aug 03, 2010 | 2000 GMC Yukon XL

1 Answer

How do I replace the studs on the rear wheel


remove wheel and brake assembly, drive broken stud through back off the hub. Put new stud through hole and use a spacer and an old lug nut to pull stud till its seated in hub.

Feb 27, 2010 | 1993 GMC Suburban

2 Answers

Describe the removal of rear brake drums


Please don't forget to rate!!!

9c23872.gif
Remove the access hole plug, then back off the adjusting screw


  1. Raise and safely support the vehicle with safety stands.
  2. Mark the relationship of the wheel to the axle flange to help maintain wheel balance after assembly.
  3. Remove the tire and wheel assembly.
  4. Mark the relationship of the brake drum to the axle flange.
NOTE Do not pry against the splash shield that surrounds the backing plate in an attempt to free the drum. This will bend the splash shield.

  1. If difficulty is encountered in removing the brake drum, the following steps may be of assistance.
    1. Make sure the parking brake is released.
    2. Back off the parking brake cable adjustment.
    3. Remove the access hole plug from the backing plate.
    4. Using a screwdriver, back off the adjusting screw.
    5. Install the access hole plug to prevent dirt or contamination from entering the drum brake assembly.
    6. Use a small amount of penetrating oil applied around the brake drum pilot hole.
    7. Carefully remove the brake drum from the vehicle.
  2. After removing the brake drum, it should be checked for the following:
    1. Inspect for cracks and deep grooves.
    2. Inspect for out of round and taper.
    3. Inspecting for hot spots (black in color).
To install:
  1. Install the brake drum onto the vehicle aligning the reference marks on the axle flange.
  2. Install the tire and wheel assembly and hand-tighten the lug nuts.
  3. Carefully lower the vehicle, then tighten the lug nuts to 100 ft. lbs. (140 Nm).
  4. Road test the vehicle for proper brake operation.

Dec 04, 2009 | 1998 Buick Century

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

1 Answer

1999 nissan quest rear brake shoes need changing


help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal
  1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
  1. Retract the brake shoes and loosen the brake adjuster screw.
975565f.gif
  1. Remove the brake drum.
----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.

f9f31b5.gif
Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches
  1. Remove the brake drum, refer to Drum in this section.
  1. Remove the upper retracting spring.
  1. Remove the lower retracting spring.
  1. Remove the self-adjuster.
38bcaa0.gif
  1. Remove the hold-down springs.
  1. Remove the parking brake lever clip and the parking brake lever.

Apr 17, 2009 | 1999 Nissan Quest

2 Answers

1996 Ford Windstar brake drum removal


use hammer hit drum to lossen rust if its loose and feels like somthing holding inside on backing plate is a rubber plug remove and back off adjuster

Oct 19, 2008 | 1996 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...