Question about Cars & Trucks

1 Answer

I have a mazda mpv 2004. The sliding doors do not work with the central locking. There is no clicking sound with either the key fob or the key. I have checked all the fuses in the foot well and under the bonnet. Please help it's driving me mad lol

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Check the cable that goes into the door to make sure is not broken/loose.
If not, you have to take the door cover out and check conmections and test if electricity is getting to the actuator. If you have power you have to change the actuator inside the door.

Posted on Jun 14, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: i have a grand voyager

dont go through all the hassles of removing the door trim just take the terminal off the battery for about a minute then reconect again worked on mine good luck

Posted on Dec 20, 2008

  • 345 Answers

SOURCE: central locking not working

does it work in the passenger door

Posted on Dec 29, 2008

  • 3 Answers

SOURCE: 1999 Audi A3 1.8T Electric Windows and Central Locking Won't work

will your passenger door open with the key and is it just one side that your windows are not working or both. if its just one side it might be your regulator motor in the door thats not working if its both it might be your central locking pump usually in the boot. however if both of them are working fine it could be that your key needs reprogrammed however i think the 1st 2 are more likely to be the problem.

Posted on Jun 30, 2009

  • 105 Answers

SOURCE: Driver side door won't lock electronically

very common problem is the door lock actuator. i would recommend replace that. a good idea also would be to remove the door panel and check all the rods that connect to the assembly and make sure one didnt pop off.

Posted on Oct 27, 2009

Testimonial: "I figured it out before i got the answer, but you were right, it was the actuator for sure, i replaced it and it worked just fine. thank you!"

  • 740 Answers

SOURCE: 2004 mazda mpv sliding door will not unlock from

sounds like the lock rod fell off. Take the door pannel off and reatach it

Posted on Mar 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Our 2001 Mazda MPV doors are not locking. Before, we were able to lock all doors just by locking manually locking from the inside on the driver side and using the remote keyless entry. Now, when we try...


The clicking you hear is the vehicle asking for the program sequence to reprogram the locking system. Apparently something threw it out of sequence, ( a battery change , jumpstart, voltage spike , etc). The programming sequence that mazda uses is really kinda crazy. I was able to locate the sequence to try. If it does not work have the dealership flash the pcm, (another word for reprogram the powertrain control module). Here is the sequence:
1) Get in MPV with ignition key, and all fobs for the vehicle.
2) Close all doors and remove ignition key if it is in ignition.
3) Open driver's door
Note: Steps 4 and 5 must be completed in under thirty seconds.
4) Repeat the following three times
a) Insert ignition key
b)Turn ignition switch to on and then to lock
c) Remove ignition key
5) Repeat the following three times
a) Close driver's door
b) Open driver's door
Locks should all lock and then unlock within a couple of seconds--you'll hear the clicking sound
6) Press any button two times within five seconds on fob being programmed.
Locks should again lock and unlock
7) Repeat step 6 for all other fobs being programmed. When done with last fob, wait a few seconds and then you should be done with the reprogramming. Each fob should now work for this vehicle.

Dec 05, 2014 | 2001 Mazda MPV

1 Answer

Need to reset central locking


state symptoms..
fobs dead., keys dead, immo dead.
there many parts to the whole system. say what parts dont work
and what precipitated the failure. (battery dead in car)?
fob, key, and door switches amany.....????
do both fobs fail?

Dec 12, 2013 | 2004 Toyota Land Cruiser

1 Answer

Key fob only opens drivers door


hit the unlock button twice. most fobs are programmed so you hit it once, drivers unlocks, and again for all the rest.

Jan 25, 2010 | 2004 Volkswagen Passat

2 Answers

Hi, I have an imported 2004 Subaru Impreza WRX. How do I reprogram the key fob after changing the battery.


first unlock car manually with key remove driver side kick panel/lower A pillar trim connect locking registration wires together(two white connectors,black wire and black and blue wire)press and hold central locking switch on drivers door in the unlock position .interior lamp will flash and an acoustic sound will be heard. now get your key and press unlock and then lock the door should lock then unlock, job done ,i persume it was to program the fob to work the central locking u wanted

Jan 17, 2010 | 2001 Subaru Impreza

1 Answer

2004 ford focos st170 drivers door central locking


First thing first-change battery in fob-most jewelers can do this as well as dealers-takes more power to unlock than lock

Sep 24, 2009 | 2004 Ford Focus

1 Answer

Rover 75 Connoisseur SE Sat/nav 2004 (53). The central locking button on top of the driver's passenger door doesn't pop down when the interior central locking switch is pressed,while the other 3 door...


It may be set in the main menu to lock only by the fob. I know on GMC's there are about 7 different locking options. I'm not a specialist in Land Rovers but the cheapest way out is to check all your options on the dash/steering wheel buttons.

Sep 09, 2009 | 2004 Land Rover Discovery

1 Answer

I have a grand voyager limited diesel. The central locking has stopped working, both via the key fobs and inside the car.However, the key fob still opens the side doors as well as the boot. Same problem...


dont go through all the hassles of removing the door trim just take the terminal off the battery for about a minute then reconect again worked on mine good luck

Jul 30, 2008 | 2004 Chrysler Voyager

5 Answers

Mazda MPV 2000


Try "resetting" your keyless entry code. Which is a fancy way of explaining that I broke my keyless entry key fob and had to order a new one. It came w/ instructions explaining how to get the new fob to speak to the car's computer. It was weird (turn key on and off 3 times, open and close door three times, etc. **I'm sure my neighbors were watching and laughing**), but it worked. I'll scan and email you the insrtuctions if you wish. Dan: dcarterlaw@lycos.com

Jul 07, 2008 | 2000 Mazda MPV

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...