Question about 1992 Isuzu Rodeo

Open Question

Where is the ecu on a 1992 isuzu rodeo? - 1992 Isuzu Rodeo

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Richie_asg1
  • 1036 Answers

SOURCE: 1992 Isuzu Rodeo Distributor wires

Hi,

On the 3.2L distriburorless ignition, the firing order is a straight 1-2-3-4-5-6.

Cylinder numbering .

88c39f7.jpg-

Hope this works for you

Posted on Jul 05, 2008

Richie_asg1
  • 1036 Answers

SOURCE: 1992 Isuzu Rodeo Distributor wires 3.1L engine

Hi,
Isuzu seem to have complicated things by changing engines, firing orders and even direction of rotation! As you can see, they've numbered the cylinders the other way than the 3.2L.

The Firing sequence for the 3.1 (traditional distributor) 6 cylinder is as follows -

d6e5b2a.jpg

If you take the distributor cap off, there should be a "No.1" formed on the inside. Stick a lead on this before you put the cap back on and go from there.
As leads are different lengths, you may have to swap a few to find the best fit.

I think 2 of them will look out of place - but that's the way it's designed. Just make use of clips for holding them neatly.

Thanks for using Fixya.









Posted on Jul 06, 2008

lady_montana
  • 18 Answers

SOURCE: Isuzu Rodeo w/3.1L engine

Front Passenger side on cap is 1 - if you look on the inside of your cap there SHOULD be a pin marked with a 1, and the plugs go CLOCKWISE not counter. Just had the same problem myself with my 91 Rodeo. Cylinders are as follows Passenger side (front to back) 1 - 3 - 5, Driver side (front to back) 2 - 4 - 6. I called the Isuzu dealer and they told me it was counter clockwise, but when I hooked it up that way it backfired through the Carb.

Posted on Jul 19, 2008

honeymokey
  • 3113 Answers

SOURCE: Oil used in a 1992 Isuzu Rodeo

I worked for an Isuzu dealer and we used 10w30. All Isuzu v6's use oil and is normal for 1 or more qts. per 1500 miles per. Isuzu reps.!

Posted on Jan 06, 2009

  • 1 Answer

SOURCE: the location of the ecm fuse on 98 isuzu rodeo

ECM fuese are located in the fusebox in the engine compartment-left sidefacing the vehicle.

Posted on May 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 Isuzu rodeo 3.1 no spark I have change almost everything that I can think of except for my ecm relay could this be at fault ?


1992 no spark on all 6 cylinders.
ok, did you first look at the schematic on ECU and SparK>?
lets do that and see. now.
spark systems are vastly changed, from 1990 to 2000
evolutionary, that means I must look up what's there first.
lets tick them off.
1: fuses good, means test them if they L**k good.
there are 6 fuse here , for this to work. 2 for ECU relay.
2: head lamps work (bright, ok battery seems strong) and cranks.
3:key on , cluster glows, and all those warning lamps, but but the CEL it must glow, or the ECU has no power, the ecu fires the coil via an Ignitor so ECU must have power and CEL glows
Check engine light.
if that work the engage the diag jumper wire clip
this enables flash diagnostic codes.
then crank for 5seconds, if you get the code for dead CKP bingo.
how do to that is here.
http://www.troublecodes.net/isuzu/

now your relay question?
key on, all wires on the relay go hot 12vdc.
but the black wire (its ground)
the 2 green wires on relay must be 12vdc, output to ecu. the inputs are fused x2

to test a so called good looking fuse.
we use 2 methods, ill show 1.
ohms. with your DMM set to Rx1 range (lowest)
measure he fuse. 0 ohms good, infinity bad.
we use volts on key on car, 12vdc both sides of fuse.
there are some rare exception on that, (fused grounds)
but not this car.
the fuse related are hot all time, or hot keyon.

Nov 26, 2016 | 1992 Isuzu Rodeo

1 Answer

Where do you plug in the code reader for a 92 isuzu. Rodeo


There is no OBD plug to speak of until 1996 and above. However, some models do have a "diagnostic plug" (3 terminal plug) behind the left "drivers footwell" kick panel. There should be a 3-wire harness with a white plug on the end. If you short the #1 and #3 terminals together and then turn on the key, TO RUN ONLY....NOT ALL THE WAY TO START, you should get codes to blink on your "Check Engine Light" or "MIL". Codes can be found online if any have been saved to the ECU.

Oct 25, 2013 | 1992 Isuzu Rodeo

1 Answer

I need to see the diagram to re-assemble the locking hub diagram for 1992 isuzu rodeo


We have no such diagrams. You will need to try and find a used factory service manual. ebay is a good source.

May 24, 2012 | 1992 Isuzu Rodeo

1 Answer

How do you take off a rotor on an 1992 Isuzu


you need to remove the locking hub

Sep 25, 2009 | 1992 Isuzu Rodeo

1 Answer

How do you put a 1992 isuzu rodeo back in time?


you mean the timing chain broke??? you will need it replaced and when they do that, it will be back in time.

Sep 23, 2009 | 1992 Isuzu Rodeo

1 Answer

95 Isuzu Rodeo. It will drive fine for a little


Check on the engine ground stud under the air intake tube.

This stud is well hidden under a lot of black electrical tape.

There are few wires ground to this stud.

THIS IS the ground for the ECU.

Take off the nut and check/clean all rings.

This is the grounding point for the ECU.

Next time you has the same problem,check the ECU and see is the LED is lite up.

NO power to ECU = no lite LED

ECU is near your left foot when you site on the drive seat.

Jul 10, 2009 | 1995 Isuzu Rodeo

1 Answer

Isuzu Rodeo Photo Cover fuse


my fuse for the rear tail lights keeps blowing after 20 sec,

Nov 30, 2008 | 1992 Isuzu Rodeo

1 Answer

1992 Isuzu Rodeo Distributor wires


Hi,

On the 3.2L distriburorless ignition, the firing order is a straight 1-2-3-4-5-6.

Cylinder numbering .

88c39f7.jpg-

Hope this works for you

Jul 05, 2008 | 1992 Isuzu Rodeo

Not finding what you are looking for?
1992 Isuzu Rodeo Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...