Question about Cars & Trucks

1 Answer

I have 2000 mazda b2500... what is thw idle supposed to be set At

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 10 Answers

650-750. These have a common problem with the IAC valve.

Posted on May 16, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76649 Answers

SOURCE: Need fuse diagram for mazda b2500

go to the link below and choose the 1998 ford ranger as the truck, they are the same, then follow the link to ford site and download the 1998 ranger owners manual, the fuse diagrams are in there
http://www.edmunds.com/ownership/howto/articles/120189/article.html

Posted on Sep 16, 2009

Mustgo
  • 2359 Answers

SOURCE: i have a low idle problem in my 99 mazda B2500.

Low idle problem can cause by a lot of components.


Dirty air filter

Dirty injectors + o-rings

Vacuum leak at intake manifold and vacuum hose.

Bad Idle Air Control Motor (IAC)

Low compression (170 psi + is OK)


Start cleaning and repair these trouble spots and see is there any improvement.


Please rate my answer if it's useful to you.


Cheers,

MUSTGO.






Posted on Dec 13, 2009

  • 280 Answers

SOURCE: mazda 2000 B2500 main, rod+cil head bolt torque

call your local auto zone-they can give them to you

Posted on Mar 23, 2010

  • 365 Answers

SOURCE: How to change front disc brake pads on 2000 Mazda

jack up car, remove the road wheels, at the rear of the caliper you will have 2 or 3 bolts holding the caliper onto the stub axle, remove the bolts and remove the caliper, remove the outer pad, leave the inner pad in place and use a "G" clamp to compress the brake piston until it has bottomed, if this is not done the new pads will not fit back over the rotor as the piston is too far out and the new pads are thicker than the old ones.
place the new pads in the caliper and fit over the rotor, replace the 2 or 3 bolts that hold the caliper in place, replace the road wheel, tighten the nuts and lower the car to the ground, pump the brake pedal to see if you have brakes, if you do have brakes take it for a test drive away from any traffic if possible

Posted on Jun 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 mazda b-2500 won't idle down fast


The IAC (idle air control ) it sounds like it needs a good cleaning, or replacement. Good-Day!

May 14, 2014 | 1999 Mazda B2500

1 Answer

I am changing a timeing belt on a 2000 b2500 mazda pickup I can't get the crankshaft pullie off


Hi!

Sometime you will need a Puller to do the job. You can rent one at Advance autoparts. Good luck

Jul 01, 2011 | Mazda B-Series Truck Cars & Trucks

1 Answer

My 2000 b2500 revs so high when idling. what could it be? the IAC,TPS?


Your engine has a vacuum leak, causing the idle to peak. Check all the hoses under the hood for vacuum leaks. You have a leak some where for sure. Thanks.

Jan 30, 2010 | 2000 Mazda B-Series

1 Answer

I need location on idle control valve on 2000 mazda pk b2500


side of the throttle body, here is a picture of the valve,297cb1c.jpg

Jan 23, 2010 | 1999 Mazda Pickup

2 Answers

Mazda bravo blowing white smoke


blowing white smoke is almost always a symptom of an engine coolant leak at the cylinder head gasket. remove each spark plug and look for a dis-colored plug to find which cylinder is leaking.

May 26, 2008 | 2007 Mazda B Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...