Question about 2006 Ford Escape

Open Question

Broken mounting clip on side of factory 2006 Ford Escape radio.

In attempting to remove radio with removal tool, technician bent and then broke 1 side mounting clip on 2006 Audiophile 6 radio. Can clip be replaced? Seems to be attached with a rivet.

If not, I would replace the radio. Part number is 6L8T-18C815-FC. Found a 6L8T-18C815-FD online (last character is "D" not "C"). Will this radio work? All photos, including rear plugs and pin counts are the same.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 6 CD Changer/Radio on 2002 Ford Escape

Check this, it worked for me

http://www.i-hacked.com/content/view/213/45/

Posted on Oct 15, 2008

Ad
fknstart
  • 404 Answers

SOURCE: removal of rear brake drum 2002 ford escape

make sure handbrake is off take wheel off hit the drum with a mallet not steel,as it will brake,hit on outter diametter face of drum, try and rotate as you twist off

Posted on Jan 05, 2009

  • 26 Answers

SOURCE: Radio Aux feature and not plug connection

http://www.installer.com/cars/by_car.php?carid=6330

Posted on Feb 28, 2009

  • 10 Answers

SOURCE: double din radio doesn't fit in dash

i have a 2002 ford escape and i bought a double din radio and it did not fit and found out it is actually a din and 3/4 with out serious mods (cutting a bigger hole in dash) double din wont fit i bought a single din stereo and a din a 3/4 dash kit works fine

Posted on Jun 17, 2009

  • 4340 Answers

SOURCE: need to replace rear wiper blade on a 2006 ford

These days the entire blade and holder assembly is replaced, not just the blade. The holder separates from the arm.

Posted on Nov 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford escape 2006 awd driveshaft carrier bearing stud replace


if flush break than drill and use a remover can buy a remover at most hardware-home-auto stores ====if their is enough to grab stud use heat carefully and a stud tool -vice grip or anything that will grab the stud to remove it

Jan 12, 2013 | 2006 Ford Escape Hybrid

2 Answers

I need to remove my 6 cd changer am fm radio how does ut come out please help so i can replace it


you need the radio removal u shaped tools. you can buy for $5 at uto store.

SECTION 415-01: Audio Unit 2002 Escape Workshop Manual
REMOVAL AND INSTALLATION Audio Unit
Special Tool(s) s2k~us~en~file=st1445a.gif~gen~ref.gif Radio Removing Tool
415-001 (T87P-19061-A)
Removal and Installation
  1. Disconnect the battery cables. For additional information, refer to Section 414-01 .
  1. Remove the audio unit.
    1. Insert the special tool into the radio face plate and release the radio retaining clips.
    1. Pull outward on the special tool and remove the audio unit from the instrument panel.
  1. Disconnect the connectors.
  1. To install, reverse the removal procedure.

Apr 22, 2011 | 2002 Ford Escape

1 Answer

How do i remove a factory radio from a 1994 ford 150


I have used strong paper clips and have also used coat hangers for the removal tool.
If you look at the radio you will notice four pinholes at the edges/corners of the radio. These are the holes the tool I am about to describe will go in. One tool for the left side of the radio and one tool for the right.
Cut the coat hanger to about 5-6 inches in length. Bend the cut piece to a "U" shape. Repeat the process for the 2nd tool.
Stick each tool into the pinholes on either side. You will notice that at first there will be a little resistance then it will slide further in easily...this means you have it in right. Do not push it in as far as it will go.
Now that you have both tools set, gently pry outwards towards the side the tool is inserted in...both at same time. Example: The left tool, you want to pry it to the left and the right will be pushed to the right.
As you are pushing them, gently rock the radio side to side. Once it comes about a 1/4-1/2 inch out, you have gotten past the retainer clips and the radio can be pulled out by hand.
To install the radio, just push it into the dash, no tools needed. When it is fully seated, you will hear the retaining clips lock into place.

Feb 28, 2010 | 1991 Ford F150

2 Answers

How do I get the factory radio out , so I can put


Removal & Installation You will need radio removing tool T87P-19061-A or its equivalent to perform this procedure.
  1. Disconnect the negative battery cable.
  2. Place the temperature control switch to the COLD position.
  3. Unlock the temperature cable by pulling down on the tab.
  4. Disconnect the cable while holding the tab down.
  5. Using the radio removal tool, pull the integrated control panel from the instrument panel.
  6. Unplug the vacuum harness, antenna lead and the electrical connections from the rear of the control panel.
  7. Remove the control panel.
To install:
  1. Attach the vacuum harness, antenna lead and the electrical connections to the rear of the control panel.
  2. Install the control panel into the instrument panel.
  3. Connect the temperature control cable.
  4. Connect the negative battery cable

Jan 19, 2010 | 1999 Ford Escort

1 Answer

How do i get the tape deck out to install a cd player?


Hope this helps! Please don't forget to rate!

54d542f.gif
Example of the special radio removal tool

9a1b311.gif
Exploded view of the radio mounting and wire connections. Note the rear support and the bracket that it attaches to

  1. Disconnect the negative battery cable.
  2. On 1991-92 models, remove the finish panel from around the radio assembly.
c6c1f8d.gif
To remove the radio, insert the removal tool prongs into the release clip access holes (arrows)

e284637.gif
Push in approximately 1 inch (25.4mm) to release the retainer clips, then pull straight out to remove

3. Insert the radio removal tool T87P-19061-A or equivalent, into the radio face.

4.Press in 1 inch (25.4mm) to release the retaining clips, then using the tool as handles, pull the radio out of the instrument panel.

176156b.gif
Disconnect the antenna ...

a6fe70a.gif
... and the electrical wire harness plugs from the back of the radio


  1. Disconnect the antenna and wiring connectors from the radio.
To install:
  1. Connect the wiring and slide the radio into the instrument panel. Ensure that the rear mounting bracket is engaged on the mounting track in the panel.
  2. If removed, install the finish panel
  3. Connect the battery cable.
  4. Check the operation of the radio.

Jan 10, 2010 | 1992 Ford Explorer

1 Answer

How do I remove the factory stereo on a 1993 Ford F350?


there are 4 holes in the face of the unit,2 on each side,an inch or so apart.use two stiff wires bent into a U shape or an inexpensive pair of OEM RADIO REMOVAL TOOLS.push tools into holes to release retaining clips,pull tools outward and slide radio out.

Oct 13, 2009 | 1993 Ford F350

1 Answer

Radio dash removal


locate the 4 holes in the panel,2 on each side,1 3/8 inches apart.using two stiff wires bent in a 'U' shape,or an in expensive ''OEM RADIO REMOVAL TOOL'' [recommended] push tool in holes about an inch to release internal clips,appply outward pressure and pull unit out towards you.to replace slide unit back in untill it 'clicks in place.

Sep 26, 2009 | 2000 Ford Taurus

2 Answers

I would like to remove and replace the radio from a 1990 ford f-150. How much of the plastic dash needs to be removed if any?


are there 4 small square holes on the face of the radio?an inexpensive tool or two stiff wires bent in a U can be pushed into the holes,L & R to release the clips that hold the radio in.

Sep 21, 2009 | 1990 Ford F150

1 Answer

2002 ford explorer radio removal and installation procedure


You have to have special ford radio tools. they look like two horse shoes. they clip into the two holes on either side of the radio and then you push outwards and pull on the clips at the same time and the radio slides right out. the tools are usually inexpensive and can probably be found at local auto parts store

Apr 07, 2009 | 2002 Ford Explorer

3 Answers

Radio reciever ....cant get it out


First remove the selector trim panel for the Auto tranny or gear shift and boot trim panel for a manual tranny. remove the cigarette lighter assembly and disconnect the connector. remove the 2 radio mounting screws. You need the insert two radio removal tools T87p-19061 or equivalent into the face plate holes until you feel the tension of the holding clips. If this is the first tome removing the radio, the flashing of the bezel facing has to be broke. This may require extra force. flex outward on both sides of the radio simutaneously and pull the radio out using the tools as handles. Then dissconnect the electrical connectors. Hope this helps.

Oct 04, 2008 | 1991 Ford Probe

Not finding what you are looking for?
2006 Ford Escape Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...