How to check transmission oil in a sprintshift transmission

Is the transmission oil still a bright red colour or has it gone milky ( coolant in the transmission oil from a failed radiator cooler) check engine coolant for oil contamination ( transmission oil in the radiator from failed oil cooler)

yes for sure. trans input seal is leaking

There are two types of transmissions in 1991 Toyota Corolla. Manual Transmission and Automatic Transmission.
1. Manual Transmission:
The transmission oil is checked through a level bolt which is provided to the left CV joint side in the middle of transmission. To check the oil level, park the car on a level floor, remove the level bolt with 22 mm or 24 mm spanner. If the oil starts coming out of this hole the oil level is considered OK. If not, top up the oil till it starts coming out and tighten the bolt. The recommended manual transmission oil grade is 75W/ 90W and total capacity is 2.4 Litres.

2. Automatic Transmission:
Warm up the engine, park the car on level floor, pull up the hand brake, gear lever stick in P, keep the engine start, let the radiator fan come on, take the auto-transmission stick out, wipe it with a clean dust free cloth, insert it in, again take it out, keep the stick in horizontal position and check the oil level. At operating temperature the auto-transmission oil level should be at upper level (Hot). If not, add oil to mach the mark. The recommended auto-transmission oil is Automatic Transmission Fluid (ATF) Dexron II, and total (drain and refill) capacity is 1.4 Litres.

Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES
Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

WELL IF ITS ENGINE OIL SHOOTING OUT CHECK AROUND OIL PRESSURE SENDING UNIT AND OIL FILTER SEAL LEAKING OR OIL FILTER HAS A HOLE IN IT. IF YOU TALKING ABOUT TRANSMISSION CHECK TRANSMISSION COOLER LINES GOING FROM TRANSMISSION TO RADIATOR.

TRANSMISSION FLUID LEAKS,CAN BE FOUND AROUND PAN GASKET.CHECK PAN GASKET,IF IT LOOKS WET AND YOU SEE FLUID DRIPPING AROUND THE EDGE OF OIL PAN, REPLACE PAN GASKET, WHILE YOU REPLACING PAN GASKET REPLACE TRANSMISSION FILTER WHILE OIL PAN OFF.IF TRANSMISSION OIL PAN NOT LEAKING, CHECK TRANSMISSION OIL COOLER LINES GOING INTO RADIATOR YOU WILL LOOSE A LOT OF FLUID THERE ALSO TORQUE SHAFT SEAL WILL CAUSE HEAVY FLUID LEAK WHILE ENGINE RUNNING CHECK OIL COOLER LINES AND LOOK AT THE TORQUE AREA WHILE ENGINE RUNNING YOU WILL SEE FLUID POURING WHILE ENGINE RUNNING THE OIL PUMP PRESSURE WILL PUSH FLUID OUT AT THE LEAKING AREAS.

HIGH PITCH WHINNING NOISE IS FAULTY TRANSMISSION OIL PUMP.HAVE THE TRANSMISSION FLUID PRESSURE CHECK AT A TRANSMISSION SHOP.IF TRANSMISSION OIL PUMP TOO WEAK OR MALFUNCTION.YOUR TRANSMISSION WONT HAVE ENOUGH OIL PRESSURE FOR FORWARD GEAR , REVERSE GEAR, BAND OR SHIFT VALVES IN VALVE BODY.NOTHING WILL WORK TRANSMISSION.OIL PUMP LIKE HYDRALIC PUMP KEEPS EVERY THING WORKING..

The sycroniser is not meshing the gears all the way. So in turn when under pressure it slips out.

the oil reservoir could have damage. check for the other oil line.