Question about Daihatsu Sirion

Open Question

Daihatsu sirion time belt - Sirion Daihatsu Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Daihatsu Sirion

I assume you are changing the timing belt. I am a mechanic and although not familiar with your vehicle, you would usually locate the timing mark on the bottom pulley and line this up. Careful not to turn the engine over too hard as pistons can strike valves. then you should look for similar marks on the camshaft pulley[s], and line these up. Then fit belt. This has to be tensiond correctly which is important. Hope this helps. Mike the bike01.

Posted on Aug 19, 2008

  • 98 Answers

SOURCE: 1999 Daihatsu Sirion

Your engine is probably an EJ-DE twin cam 12 valve.

Generally Daihatsu belts have marks on them that line up with dimples on the sprockets for the intial phasing. You rotate the engine to top dead centre on No1 piston and install the belt from there. The cams should be not be putting any pressure on the intake and exhaust valves of No1 when phased correctly.

Posted on Oct 10, 2008

  • 491 Answers

SOURCE: where is cam belt situated on daihatsu sirion

THERE IS NO CAM BELT , THE TIMING BELT IS TURNED BY THE CAMSHAFT , THE POWER STEERING IS POWERD BY THE CRANKSHAFT PULLY WHICH ALSO POWERS THE ALTERNATOR,

Posted on Oct 25, 2009

Alias117
  • 2 Answers

SOURCE: Hi, Does anybody knows where power

Engine room back box near the batteri, has the fuses if i recall correctly.

Posted on Oct 26, 2010

  • 1 Answer

SOURCE: my daihatsu sirion abs light was always on what is

Hi, the light is basically telling you that there is a problem with a sensor or the sensor circuit. Find the eobd 16 pin plug and bridge the fourth pin on the top and the fifth pin on the bottom row with the ignition off. Now turn the ignition on and the light will flash and display codes. The series of first flashes indicates tens n the second series shown after a longer pause between flashes. Eg code 21 would be 2 flashes then a pause and one flash thereeon. The codes can be gotten from toyota nation. This will direct you to which sensor is faulty. Once the repair is done pump the pedal eight times and the light should blink constantly. Now turn off the key and pull out the bridging wire. Enjoy!!

Posted on May 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How i can replace drive belt for daihatsu sirion 2006 1.3i type k3 engine


from the front.
lever the tensioner and take the old belt off

Jul 17, 2016 | Daihatsu Cars & Trucks

1 Answer

Do I have to remove the engine from the car to change the timming belt of a Sirion GTVI


most likely. timing belts are a notoriously hard (and usually expensive) fix. you may have to hit a garage for that one. make sure of that knock as well

Dec 08, 2014 | 2005 Daihatsu Sirion

1 Answer

Why is there a squeaking noise only when I drive at night


at night, it is cold, your drive belt gets worn other time, when it's cold at night it doesn't get much grip, so it squeaks, what you can do is tighten it up, find which one is loose by pressing on them. The concept of belt tensioning is simple, look it up, on all cars work the same.

May 05, 2014 | Daihatsu Cars & Trucks

3 Answers

Is replacement of 2007 Daihatsu Sirion 1.3 fanbelt a relatively simple task or is it for a professional mechanic only?


DO IT YOURSELF... It IS fiddly but perfectly do-able.. easiest way to do it is to remove plastic 'dirt shield' from driver's side inner wing (next to drive shaft and brake line) obviously wheel removed, or rotated is ok.. removal of modern plastic 'tat' is simple (area of cylinder head) allowing as much finger access as possible..not much room down the side of these puppies!! Next you need to de-tension the 'serpentine' belt BUT I WOULD RECOMEND DRAWING BELT & PULLEY SET UP FIRST or taking several photos.. as a reminder of if belt goes over or under (makes sense when you see it) Use blunt engineer's screwdriver (or any blunt long driver, rod, etc) to help push and pull old and new belt about.. REMEMBER TO RE-TENSION THE TENSIONING PULLEY...BUT DONT OVER DO IT!! THE BELT WILL TIGHTEN EVEN MORE AFTER SHORT RUN IN.. ALLOW SLIGHT DEFLECTION.. 6 to 10mm should do... cleanliness is the key really, as with all engine jobs(!) Allow 2hrs to do... if you've never done before... ok?

Mar 04, 2013 | 2007 Daihatsu Sirion 1.3

1 Answer

Where is cam belt situated on daihatsu sirion. Is it adjacent to the fan belt?. Would the cam belt affect the power steering?


THERE IS NO CAM BELT , THE TIMING BELT IS TURNED BY THE CAMSHAFT , THE POWER STEERING IS POWERD BY THE CRANKSHAFT PULLY WHICH ALSO POWERS THE ALTERNATOR,

Oct 25, 2009 | 1992 Daihatsu Charade

1 Answer

Daihatsu Sirion


I assume you are changing the timing belt. I am a mechanic and although not familiar with your vehicle, you would usually locate the timing mark on the bottom pulley and line this up. Careful not to turn the engine over too hard as pistons can strike valves. then you should look for similar marks on the camshaft pulley[s], and line these up. Then fit belt. This has to be tensiond correctly which is important. Hope this helps. Mike the bike01.

Aug 19, 2008 | Daihatsu Charade Cars & Trucks

1 Answer

1999 Daihatsu Sirion


Your engine is probably an EJ-DE twin cam 12 valve.

Generally Daihatsu belts have marks on them that line up with dimples on the sprockets for the intial phasing. You rotate the engine to top dead centre on No1 piston and install the belt from there. The cams should be not be putting any pressure on the intake and exhaust valves of No1 when phased correctly.

Aug 13, 2008 | 1988 Daihatsu Charade

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...