Question about 2004 Cadillac SRX

Open Question

How do you replace a fuel pump in a 2010 Cadillac srx

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Posted on Jan 25, 2009

Ad
techbuster
  • 5081 Answers

SOURCE: rear liscese plate bulbs on 05 cadillac srx

First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.

Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.

Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.

Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.

OPTIONAL:
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.


Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.

The bulbs come in a two pack of cost $4.95 .

Posted on Nov 24, 2009

  • 1 Answer

SOURCE: Changing fuel filter on 2004 Cadillac SRX

If you go to the auto parts store they should have a fuel line disconnect tool that has a 5/16ths end an a 3/8ths end. The tool is shaped like an X. Before you start you need to pull the fuel pump fuse under the front of the REAR passenger side seat while the car is running and let it stall. it will release the built up pressure. This is important unless you want gas to spray every where. Then take the tool and start with the end of the filter with two lines. Place the appropriate end of the tool over the smallest inlet, push the tool in then pull the line towards the filter and then push the line away and it should disconnect. Do the same with line above. Then you can use the two appropriate size wrenches to disconnect the outlet end. reconnecting the new filter is simple just make sure your quick connect lines click in all the way and you tighten the outlet line well, I think its like 22 or 25 ft/lbs.

Posted on Dec 15, 2009

  • 396 Answers

SOURCE: Wiring diagram for 2009 Cadillac SRX

Try your dealer parts counter.

Posted on Jan 16, 2010

  • 4340 Answers

SOURCE: Are you suppose to use

Really, you need to use what the manual reccomends, in your case that should be premium. While you will usually not suffer damage from using lower grade, you will suffer performance and economy loss.

Posted on Oct 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why is there water in my head lights in my Cadillac 2010 srx


Water buildup can be due to humidity and condensation. This is a common problem on the Cadillac SRX 2010-2011(at least). The replacement can cost about $1,500 USD through a dealership.

Aug 10, 2017 | Cadillac Cars & Trucks

1 Answer

HOW TO CHANGE THE FUEL PUMP ON 2010 SRX 4 DR. V6


did you test or are you guessing ? The fuel pump relay allows the ECM to energize the fuel pump. The ECM enables the fuel pump whenever the crankshaft position (CKP) sensor pulses are detected. GM Fuel Pump Relay Testing

Dec 01, 2016 | 2010 Cadillac SRX AWD

1 Answer

Removal of fuel rails 3.0L Cadillac srx 2010


Upper intake manifold will need to be removed, and then you can remove the 4 fuel rail retaining bolts.

Aug 19, 2015 | Cadillac Cars & Trucks

1 Answer

Where is the fuse box located in the 2010 Cadillac SRX


call the nearest caddilac dealer they will tell u where it is for free

Jan 17, 2013 | 2010 Cadillac SRX

1 Answer

My 2010 Cadillac SRX trunk won't open with the doors unlock from inside the car, from the remote and from the touch pad button under the license plate. Please someone let me know if they know the


sounds like a fuse is bad for that circuit..check and replace if bad..in an emergency to gain acess to the trunk, remove the back seat by taking the base out first then the back of it..remove the noisebarrier(fiberboard or batting) and the trunk is accessible by a smaller person who can trip the lock from inside manually..good luck and reposr please..

Jan 17, 2013 | 2010 Cadillac SRX

1 Answer

How do you change the fuel pum on cadillac srx 2004 (4.6 L)? Is the gas gauge connected to the fuel pump? Thanks


You have to drop the fuel tank to access the fuel pump and sending unit. Yes the fuel pump and gauge sending unit are separate but connect together in one assembly.

May 22, 2010 | 2004 Cadillac SRX

Not finding what you are looking for?
2004 Cadillac SRX Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...