Question about 2005 Mazda 6

Open Question

How do I bleed air out of my Mazda diesel fuel system

I r an out of fuel in my Mazda diesel truck, I replaced the fuel but now won't start Do I need to prime fuel pump or bleed air out of the fuel lines and if so how do I do it

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 32 Answers

SOURCE: 94 MAZDA MX3 REPLACED FUEL

check the fuel pump relay. it is located under the hood in the fuse box directly in front of the battery

Posted on May 03, 2009

localwonder
  • 6784 Answers

SOURCE: how do i replace the fuel pump in my 1993 mazda 626 2.5

1. Relieve the fuel pressure and disconnect the negative battery cable.

2. If not already removed, depress the clips on each end of the rear seat cushion and remove the cushion.

3. If not already done, detach the electrical connector from the fuel pump/sending unit.

4. Remove the attaching screws from the fuel pump/sending unit access cover and remove the cover.

5. Disconnect the fuel supply and return hoses from the fuel pump/sending unit.

6. Remove the attaching screws and the fuel pump/sending unit from the fuel tank.

7. Detach the sending unit electrical connector, remove the sending unit attaching nuts and remove the sending unit from the fuel pump assembly.



To install:

1. Attach the sending unit to the fuel pump assembly and install the nuts. attach the sending unit electrical connector.

2. Install the fuel pump/sending unit into the fuel tank with a new gasket and install the mounting screws.

3. Connect the fuel supply and return lines.

4. Install the access cover and the mounting screws.

5. Attach the sending unit electrical connector.

6. Position the rear seat cushion over the floor, making sure to align the retaining pins with the clips. Push down firmly until the two retaining pins are locked into the rear seat retaining clips.

7. Connect the negative battery cable, start the engine and check for proper system operation and for fuel leaks.

Posted on Jun 13, 2009

  • 9 Answers

SOURCE: mazda 6 diesel wont start

Have you run the car without fuel? There must not be any air in the fuel line... Blead the fuel line of air and try to start it. There should be bleader screws under the hood....

Posted on Jun 13, 2009

  • 66 Answers

SOURCE: I need a fuse box diagram for a 1997 mazda protege dx

Yes - sounds like a Pump fuse, relay, or a pump...When you cycle the key (off-on-start-on) do you hear the pump running?
The fuel pump fuse may be under the hood with the other engine fuses - and it well may not be -(there is an accessory fuse box that has all the fuses for the inside accessories in it - located in the passenger compartment somewhere)- also check the kick panels at the drivers left foot and the passengers right foot -(If they pop off easily - The fuse box plastic cover will pop off easily, not attached with screws - so if you see screws or nuts, it won't be there) Look up under the dash on the drivers side, and also lastly check in the glove box- If you cannot find it, I'd see if I could find a Mazda "lovers" web-site - Often they post what is called "component locator" information, that would tell you exactally where it is (Normally you have to pay for access to that information - gotta love the web), or you may be able to locate a electronic owners manual there as well which will definitely tell you ...Best of luck and hope that helps some....

Posted on Sep 13, 2009

wracefans24
  • 1985 Answers

SOURCE: How to Replace a Fuel pump on a 2000 Mazda 626

yes it isn't that much if you buy them.they slide inside the coupler and release the line.

Posted on Dec 27, 2009

Testimonial: "Thank you didn't know if there was a tool for this."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to bleed the fuel system in the 2009 Mondeo after changing the fuel filter on a diesel


You don't. You just crank the engine until it starts. Modern vehicles work on a pressurised system with a return back to the tank. The fuel is pumped from the tank to the injectors and excess fuel is returned to the tank.

May 12, 2016 | Cars & Trucks

1 Answer

I brought a mazda premacy 2lt diesel on 2003 plate, I drove 2 miles and the car just cut out and now it won't start. I have checked fuel pump and ignition and they seem fine. Any ideas please.


check and bleed air from the fuel system. check for fuel level in the tank. run the fault codes to check for cam/crank position sensors and broken timing belt.

Jan 24, 2015 | Mazda Cars & Trucks

1 Answer

Diesel loss of power


check and change the fuel filters including the water filter.. If you are using a bio diesel then don't. Check and bleed any air out of the pump and lines. check that the air valve on top of the tank is clean and allowing the tank to vent and not get a vacuum. Check for a moss like substance in the tank as it will seriously affect the diesel and injectors. Basically It sounds as if the pump is starving for fuel from a blockage or air in the system.

Mar 02, 2014 | Mazda B-Series Truck Cars & Trucks

2 Answers

My 5.9 dodge cummins diesel won't start, I've replaced the fuel lift pump, and the fuel filter, turns over. But will not start?


Most likely you just have air in the lines.Crack them open one at a time and bleed them with the fuel pump off and on till you get fuel.If it fires dont hit the throttle let it sit and idle and close the line.Does it fire up with a small whif of starting fluid?

Mar 17, 2013 | 1999 Dodge Ram

1 Answer

Ran out of diesel now vehicle won't start


This is not unusual on a diesel. What happens is there is air in the system. If this vehicle has an electric fuel pump loosen line where fuel enters injection pump then turn ignition key to the on position and watch for fuel to appear and then quickly tighten line before turning off key. Then try to start. If does not have electric fuel pump will need a second person. One will loosen line and watch while other cranks vehicle until you get fuel and tighten line before the other person releases ignition switch unless vehicle starts first. If that doesn't do the job do this where line hooks onto each injector. Probably will not have to do this to all injectors but could run rough until all the air gets out of everything. I have farmed with diesel tractor for 25 years and dad I drove the gm vehicles with the 5.7. You normally don't start a diesel without bleeding the air out of the lines although some will self bleed most won't. Hope this does the trick.

Jun 21, 2012 | 2004 GMC Sierra 2500

1 Answer

I just replaced both fuel filters and now the truck won't start.


Hi,
If that is a DiESEL engine, you have to bleed it thoroughly until there is no air in the fuel system. Check the top of the filter and unscrew the bleeder nipple and pump it fuel and air will come out.
If it is a petrol engine, air must have been stuck on the intake fuel line, bleed it until pure liquid comes out from the fuel filter hose output.
Check your fuel gauge, you might not have enough fuel!
Hope that helps you out.

Aug 06, 2011 | 2008 Ford F 250 Super Duty 4WD

1 Answer

Diesel 1989 F-250 set too long and will roll over


You may have to bleed the fuel system. There may be a very small air leak in the fuel supply line and after a long time idle, the fuel seeps bac into the tank, leaving an air lock in the pipe. When you go to start, this air makes its way into your injection pump & needs to be bled out before the engine will start. Begin from your fuel filter bleed valve, next the injection pump using the primer pump to transfer the fuel. Next loosen off the injector pipes and crank the engine over until fuel sprays form all the joints. Tighten injector pipes and start. It may run a bit rough for to begin with, but will soon even out. If it doesn't start, repeat bleeding of injectors.

Mar 13, 2010 | 1989 Ford F 250

2 Answers

Mercedes ran out of diesel,put some


Sorry.I am not sure on your model but.If you run a diesel out of fuel,it needs to have the fuel system bled.In the book it will say how.Most common is a bleed valve.Sorry I could not help you more on your car but someone from fixya will..I just wanted to tell you what needs to be done.Sorry I could not help you straight up but wanted to tell you what is needed for your vehicle.Thanks

Sep 27, 2009 | 2001 Mercedes-Benz C-Class

1 Answer

After replacing fuel pump and filt truck wont start with started fuid


If this is a diesel you should not use starter fluid unless the glow plugs and glow plug controller is removed. If this is a diesel you most likely have air in the fuel system.When changing fuel filter on a diesel fill the filter container with clean diesel,screw the top of the fuel filter canister on open the bleed screw and turn the engine over until only clear fuel (no air bubbles)is bled from fuel system. Then you may have to turn loose the connector on the innjectors to bleed more air out of the fuel system.

Jun 15, 2009 | 1994 Chevrolet K1500

2 Answers

1985 Ford 250 Diesel Truck, Won't Start


just crack the injector nut crank it over till fuel comes out tighten nut,and so on to the others.

Jan 15, 2009 | 1985 Ford F 250

Not finding what you are looking for?
2005 Mazda 6 Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...