Question about 2006 Cadillac SRX

Open Question

Transmission band adjustment

06 SRX cadillac is there a way to adjust the bands on this vehicle

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 1987 cadillac 3rd gear band adjustment

That's a transaxle correct? 4T60E?

There is no band adjustment

If a band on any trans wore enough
to need adjustment,then the trans would
need an overhaul

Posted on Jun 26, 2012

Ad

SOURCE: how to adjust transmission bands on my 1997 cadillac deville

no adj servo controls band apply

Posted on Mar 25, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i turn on the fog lights on 2007 srx?


good afternoon Anonymous.

The manual for this model can be found here:
https://www.cadillac.com/content/dam/Cadillac/Global/master/nscwebsite/en/home/Owners/Manuals_and_Videos/01_images/2007_cadillac_srx_owners.pdf on the Cadillac website. There is mention on manual page 181 of turning the fog lamps on and off with the Fog Lamp Band. If you look on page 167, it ties an illustration to Fog Lamps, showing you where the band is on the Turn Signal Lever.

Hoping this answers your question!
D

Nov 30, 2015 | 2007 Cadillac SRX

1 Answer

How do i adjust the transmission bands on a 93 toyota camry?


Adjustments - AutoZone

www.autozone.com/repairinfo/.../repairGuideContent.jsp?page...
AutoZoneBoth band adjustment screws are located on the left side of transmission, the ... 13: Automatic shift control adjustment-1989-93 vehicles with the 3.8L engine .... Ex. 04 Camry Battery See More Examples ... Explorer 4WD 4.0L EFI SOHC 6cyl; 2001 Toyota Corolla 1.8L EFI DOHC 4cyl; 2004 Infiniti M45 4.5L SFI DOHC 8cyl.

Aug 24, 2015 | Toyota Cars & Trucks

1 Answer

Do a 06 charger daytona have bands to adjust


You only adjust transmission bands, when building the unit

By the time they have to be adjusted, the bands are worn &
the trans is shot & in need of a rebuild

Jul 22, 2014 | Cars & Trucks

1 Answer

How you adjast the bands


Transmission Bands are adjusted when the unit is rebuilt
& need no adjustment, as they wear very little & do not solve
any problems.

The Band is brought down tight on the drum & then backed off to
whatever the book says

When you come here please provide at least a vehicle & some
details

Nov 25, 2012 | Cars & Trucks

1 Answer

1987 cadillac 3rd gear band adjustment


That's a transaxle correct? 4T60E?

There is no band adjustment

If a band on any trans wore enough
to need adjustment,then the trans would
need an overhaul

Jun 26, 2012 | 1987 Cadillac DeVille

1 Answer

Automatic transmission service adjustments for 2000 mazda bravo


There should not need to be any "adjustments" for a normal fluid and filter service for your vehicle, unless you have replaced some parts of your transmission that requires adjustment such as the gearshift lever, intermediate and overdrive band, throttle cable, or transmission range sensor/switch.

With that said, the band adjustment specs are "Tighten the band adjusting screw to 10 Ft.Lbs. (14 N.m.) then back off 2 full turns. While holding band adjusting scew stationary, tighten the locking nut to 35-45 Ft.Lbs. (48-61 N.m.)

Jun 16, 2012 | Cars & Trucks

2 Answers

Automatic transmission band adjustment


Don't have specs on band but the rule is that it should be close enough to the drum to engage without slamming, and loose enough to permit drum to turn without band dragging on it. Biggest problem I've seen people have when adjusting is that adjustment tightens down while turning lock nut. To avoid this, I usually adjust a bit looser than final adjustment so it tightens to correct position instead of becoming too tight. Don't drive 'till you have it right or you will burn band surface. When engaged in reverse, band should be applied and cannot drag. If you adjusted another band, check that one for improper adjustment.

May 10, 2009 | 1997 Jeep Wrangler

2 Answers

Where are bands located on 1996 jeep cherokee transmission and can they be tightened?


THE BANDS ARE LOCATED INSIDE YOUR TRANSMISSION AND THE CAN BE ADJUSTED. HOWEVER THIS CAN ONLY BE DONE WITH THE TRANSMISSION OUT OF THIS VEHICLE. GOOD LUCK.

Dec 30, 2008 | 1996 Jeep Cherokee Country

1 Answer

Jeep grand cherokee revs for to high before changing gear


Message:
My 2002 Dakota has been somewhat confused about shifting as well. It showed a code P1762. I dropped the pan to install a new fluid filter and fluid-(use only ATF+3 or ATF+4). Since the pan was off I decided to adjust the bands. The front band controls the 2nd gear cluster. The rear band controls the 3rd gear cluster and reverse. For a 2-3 shift, the transmission shifts back to 1st gear with the front band while the rear band engages 3rd gear. If the front band does not release the 2nd gear clutches before the third gear clutches engage, the transmission binds, which shortens the life of the transmission clutches. If the front band releases too early in the shift, the engine will overspeed (sounds and feels like a slip) during the 2-3 shift.
The front band adjusting screw is on the driver's side above the shift linkage. The rear band is inside the fluid pan near the filter.
1. Loosen band adjusting screw locknut. Then back locknut off 3-5 turns. Be sure adjusting screw turns freely in case. Apply lubricant to screw
threads if necessary. The front band adjuster is on the outside of the transmission and the locknut requires a 3/4" wrench.

2. Using Inch Pound Torque Wrench C-3380-A, a 3-in. extension and appropriate Torx� socket (T-40), tighten adjusting screw to 72 in-lb. CAUTION: If Adapter C-3705 (from SPX Miller) is needed to reach the adjusting screw, tighten the screw to only 47-50 in. lbs. torque.

3. Back off adjusting screw the number of turns listed below for your transmission.

4. Hold adjusting screw in place and tighten lock-nut to:

41 N�m (30 ft. lbs.) for the front band
34 N�m (25 ft. lbs.) for the rear band
The adjustment screw inside the case is a square head bolt. You will need a 1/4 square head socket to fit your torque wrench.
Band adjustments for each model year:
1994

* Front Band - tighten to 72 in-lb, back off 2-1/2 turns (all transmissions)
* Rear Band
o 32/42RH - Tighten to 72 in-LB, back off 4 turns
o 36/37/46/47RH - Tighten to 72 in-lb, back off 2 turns

1995-1996

* Front Band
o 42RH - tighten to 72 in-lb, back off 2-1/4 turns
o 46RH - tighten to 72 in-lb, back off 2-7/8 turns
o 47RH - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE/RH - tighten to 72 in-lb, back off 4 turns
o 46RE/RH - tighten to 72 in-lb, back off 2 turns
o 47RE/RH - tighten to 72 in-lb, back off 3 turns

1997-1998

* Front Band
o 42RE - tighten to 72 in-lb, back off 3-5/8 turns
o 46RE - tighten to 72 in-lb, back off 2-7/8 turns
o 47RE - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE - tighten to 72 in-lb, back off 4 turns
o 46RE - tighten to 72 in-lb, back off 2 turns
o 47RE - tighten to 72 in-lb, back off 3 turns

1999

* Front Band
o 42RE - tighten to 72 in-lb, back off 3 turns. (TSB 21-16-98)
o 47RE - tighten band adj. screw to 72 inch pounds, back off 1 7/8 turns
* Rear Band
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns
+ The 47RH rear band requires a 1/4" hex driver, the front band requires a
T-30 Torx driver, the filter is held in place by two screws which require a T-20 Torx drive

2000-2002

* Front Band
o 42RE - Tighten band adj. screw to 72 in-lb, back off 3 turns
o 44RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
o 46RE - Tighten band adj. screw to 72 in-lb, back off 2 7/8 turns
o 47RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
From Bill Konolday's 47RE notes: I usually go a little looser than factory
specs on this front band - backing off the adjustment screw 2 or 2 1/4 turns.
Depending on the circumstances I have backed off the band up to 2 1/2 turns.
* Rear Band
o 42RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 44RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 46RE - tighten band adj. screw to 72 inch pounds, back off 2 turns
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2003

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 1-3/4 turns
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2005

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds,
back off front band adjusting screw 1-3/4 turns for diesel vehicles,
or 1-1/2 turns, for V-10 vehicles.
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

94+ Automatic Transmission Bolt and Nut Torque Specs

* Front band adjustment locknut - 30 ft-lb
* Rear band adjustment locknut - 25 ft-lb
* Transmission pan bolts - 13 ft-lb
I just replaced the solenoid with the recommended transducer and all is fine now. The transducer cost me about $50 at a nearby dealership.
Hope this helps. -zman. rroszman@yahoo.com

Dec 09, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
2006 Cadillac SRX Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...