Question about 1999 BMW 323 Series

Open Question

Where is the exhaust cam sensor located? - 1999 BMW 323 Series

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.6l. Where is camshaft position sensor located?


There should be four of them. If you look on the front of the motor, the side where the serpentine belt is located, and just under the valve covers you should see two sensors bolted to each head with a three wire connector. The sensors on the outside are the exhaust cam sensors. the sensors on the inside are the intake cam sensors. They are typically held in place with a single bolt. 10mm socket will be needed to remove the bolts.

Apr 23, 2016 | 2005 Buick LaCrosse

1 Answer

Location of cam sensor on 2006 Cadillac model sts 4.6 engine


Here is the sensor location on the 2005 STS. My understanding is that on the 2005 it sat over the exhaust cam sprocket and on the 2006 it sits over the intake cam sprocket. That should be no problem as there will only be one to locate.
25564887-1tpq52gm5e3uksr2cuqtlsek-4-0.jpg

Mar 13, 2015 | 2006 Cadillac STS

1 Answer

How to replace camshaft sensor


The 2.4L cam sensors are located on the front or rear of the engine on the drivers side.

The 2.0L supercharged engine has a cam position sensor that reads at the end (drivers side) of the exhaust camshaft. This sensor requires a timing procedure which must be done before removing it.

Feb 10, 2015 | 2006 Saturn ION

2 Answers

Location on 2008 Cadillac sts for the crankshaft sensor


Here is the sensor location on the 2005 STS. My understanding is that on the 2005 it sat over the exhaust cam sprocket and on the 2006 it sits over the intake cam sprocket. That should be no problem as there will only be one to locate on your 2008.
location-2008-cadillac-sts-crankshaft-1tpq52gm5e3uksr2cuqtlsek-4-0.jpg

Jan 29, 2015 | 2008 Cadillac STS V6

1 Answer

Vauxhall vectra 2006 cam sensor


I have had this before it is best to change the cam and crank sensors as a pair. as a week sensor will affect the other sensor.and give a false code. as these work together. it is best to change both at the same time. i changed the crank on mine after the cam and it sorted it out. crank sensor is located near to the thermostat and under the exhaust manifold. make sure you tuck the wire away from the exhaust manifold . other end of the wire is fitted to the under neath of the injector cover and is cliped in place very easy to replace

Jul 27, 2013 | Vauxhall Cars & Trucks

1 Answer

1999 tahoe crank/cam sensor?


the 5.3 and 6.0 are famous for bad crank sensor. never a problem with cam sensor. the crank sensor is located behind the starter. you need to remove starter to get to it. ther is one bolt holding it in. check the wires going to the sensor because they are so close to the exhaust the get brittle and brake. if the wire is good change sensor and your car will run fine

Mar 21, 2013 | 1999 Chevrolet Tahoe

1 Answer

Poo14 code came up need to locate on truck where the cam sensor is


The exhaust cam sensor is on the right front corner of the cylinder head. (DRIVER RIGHT). To your right of the upper radiator hose.

Jan 01, 2012 | 2005 Chevrolet Colorado

1 Answer

2004 745li po368 code camshaft sensor B-Bank 1 but where is it located?


Intake camsensor bank #1 is located at the back of the right valve cover on the left side above the impulse wheel
Exhaust cam sensor bank #1 is located just to the right of the intake cam sensor no the back of the valve cover
Do you now where # 1 cylinder is that bank one (rule of thumb)

Apr 30, 2011 | BMW 7 Series Cars & Trucks

2 Answers

Location of cam and crank position sensors


The cam sensor is located at the front right front side of the cylinter head, while you are facing the engine.---------- The crank position sensor located below the pcv valve that is located on block not the valve cover, its below the exhaust manifold. You will have to remove the catalytic converter to see the exact view of both the sensors. The camshaft sensor is on the head. The crankshaft sensor is in the block, just below the exhaust manifold. ------------ Thanks.Helpmech.

Nov 12, 2010 | 2001 Ford Escort ZX2

2 Answers

Where is locate the camshaft position sensor on 2001 jeep grand cherokee laredo limited 4.7 l


The camshaft position sensor is located inside the distributor. It is a hall effect swich, simply remove the distributor cap and the rotor and you can lift it out, unplug and replace.
Have fun but beware a bad crankshaft position sensor can cause a false cam sensor code to be set sometimes.
Good luck.

Dec 05, 2009 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
1999 BMW 323 Series Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...