Question about 2006 Chevrolet Trailblazer

Open Question

How to adjust chevrolet trailblazer door striker

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust the drivers door to the right on a 2005 tahoe ?


Loosen the hinges and the door striker, move door to desired position, tighten hinges and striker.

Jul 07, 2014 | Chevrolet Tahoe Cars & Trucks

1 Answer

While driving dome lights come on and go off and chimes sound


{: ) It's possible that one of your doors not closing fully. The doors may need some doorlatch-to-striker adjustments, or it can be a wiring issue. A scan tool is better able to detect which of your doors is causing this unexpected signal.
You can try some diy test: Park your car, handbrakes on, engine running, and windows open. Get off your vehicle, and close all doors like you normally do. Go to each door, grasp the handle but dont open. Try to move the door to and fro and check for any play or looseness, at the same time you monitor the dash for any messages or hear the chime.

Jan 19, 2011 | 2006 Chevrolet Trailblazer

6 Answers

Doors where hard to close without the weather door seals. But with them on they will not close. The body plates more but not enuff on the cab? I need HELP.


Hi!!
The doors Hinges or Striker need to be adjusted to make up for the weatherstrip thickness. To do this, loosen the hinge-to-door bolts for lateral adjustment only. Loosen the hinge-to-body bolts for both lateral and vertical adjustment.
FRONT DOORS 1kbron_78.gif
REAR DOORS
1kbron_79.gif
BEFORE YOU START:
  • Determine which hinge bolts are to be loosened and back them out just enough to allow movement.
  • To move the door safely, use a padded pry bar. When the door is in the proper position, tighten the bolts to 19-25 ft. lbs. (26-35 Nm) and check the door operation. There should be no binding or interference when the door is closed and opened.
  • Door closing adjustment can also be affected by the position of the lock striker plate. Loosen the striker plate bolts and move the striker plate just enough to permit proper closing and locking of the door.
TO ADJUST ON A: F-150, F-250, Expedition and Navigator
HORIZONTAL AND VERTICAL ADJUSTMENT
  • Loosen the front door hinge to front door bolts.
  • Adjust the front door alignment.
  • Tighten the front door hinge to front door bolts to 19-25 ft. lbs. (26-35 Nm).

FRONT DOOR FORE AND AFT ADJUSTMENT Check the rear door hinge adjustment before adjusting the front door hinge.
  • Remove the front fender.
  • Loosen the front door hinge to body bolts.
  • Adjust the front door alignment to specification.
  • Tighten the front door hinge to body bolts.
  • Install the front fender.

1999-00 F-Super Duty Models
DOOR ADJUSTMENT The following procedure is for performing fore, aft, up, down and tilt adjustments.
  • Remove the door striker.
  • Loosen the bolts only enough to allow for slight door movement.
  • Carefully close and adjust the door until flush with the adjacent body panels.
  • Carefully open the door and tighten the bolts.
  • Re-install and adjust the door striker.
  • Check the door for proper operation and alignment.
STRIKER ADJUSTMENT Mark the position of the striker before loosening.
1kbron_48.jpg
  • Loosen the striker retaining bolts.
  • Adjust the door striker and tighten the striker retaining bolts.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Dec 09, 2010 | Ford F Cars & Trucks

1 Answer

The doors on my ford excursion rattle. how do I


You will have to loosen the striker and slide back, move back in small amounts until door is tight. also make sure its not something inside the door rattling before adjusting the striker.

Jul 20, 2010 | 2002 Ford Excursion

1 Answer

Door adjustment for a 96 f350 dropped about 1/2"


Here's the solution: You might want to park it under a tree and tie a rope to the door to pull it up when loosened.
ADJUSTMENT Fig. 1: Door hinge adjustment 84920001.gif
Fig. 2: Rear door hinge adjustment, F-350 Crew Cab 84920002.gif
NOTE: Loosen the hinge-to-door bolts for lateral adjustment only. Loosen the hinge-to-body bolts for both lateral and vertical adjustment.
  1. Determine which hinge bolts are to be loosened and back them out just enough to allow movement.
  2. To move the door safely, use a padded prybar. When the door is in the proper position, tighten the bolts to 19–25 ft. lbs. (25.5–34.5 Nm) and check the door operation. There should be no binding or interference when the door is closed and opened.
  3. Door closing adjustment can also be affected by the position of the lock striker plate. Loosen the striker plate bolts and move the striker plate just enough to permit proper closing and locking of the door.
prev.gif next.gif

Jul 13, 2010 | 1997 Ford F350 Crew Cab

1 Answer

Adjust dr side door


If you can grab the end of the door and lift on,and there's movement, what you need is the door hings bushing, most all auto parts sell this as a kit, cost about $6.00, the only adjustment you will have will be at the striker bolt, that the part where the door latch, latches to, to hold the door close, it unscrews and it will have some adjustment, but not much.There not adjustment for door hing.

Jul 08, 2010 | 1999 Chevrolet Venture

1 Answer

HOW DO I ADJUST THE DOOR HEIGHT FROM STRIKING THE LATCH TOO HARD?


this is going to take some time to get just right. there are 4 bolts that hold your door to your car that can be adjusted. the striker can also be adjusted, but save this for the last step

Feb 18, 2010 | 2006 Chevrolet Trailblazer

2 Answers

The drivers door will not close fully even if you push it real hard it really never will click into that lock position


open the door loosen the striker on the door jam and adjust it by slidding it back and forth, also if the door has drooped a little loosen the lower hinge and put a 3/8 shim between the hinge and door!!!

Nov 24, 2009 | 1990 Chevrolet K1500

1 Answer

Power slide door dosent close all the way


CHECK THE PIVOT HINGE AT THE REAR OF THE DOOR, IF BAD IT WILL THROW THE DOOR OUT OF ALIGNMENT.

THE STRIKER AT THE FRONT OF THE DOOR CAN CAUSE IT NOT TO CLOSE ALSO. SLOWLY CLOSE THE DOOR AND LOOK AT THE STRIKER TO LATCH POSITION. IT SHOULD BE AT THE CENTER OF THE LATCH. IF NOT ADJUST IT TO FIT BETTER.

CLEAN THE CONTACTS WITH SCOTCH-BRITE THEN PUT A LITTLE DI-ELECTRIC GREASE ON THEM.

Jul 15, 2009 | 2004 Chevrolet Venture Passanger

1 Answer

Driver door will not close properly>


These things can be a pain, cause I have one... Have you adjusted the striker mechanism? Your adjustments are basically the striker and the door hinges. It is possible that you have worn door hinge pin(s). You may need to adjust the hinges. Rick

Apr 15, 2009 | 1990 GMC C1500

Not finding what you are looking for?
2006 Chevrolet Trailblazer Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...