Question about 2007 Dodge Caravan SXT Minivan New Cars

Open Question

Locationf crankshaft position sensor 2011 dodge aravan crew

2011

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 30 Answers

SOURCE: 04 Dodge SRT 4 crankshaft sensor

The Crankshaft Position Sensor is located directly next to the starter.

  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Posted on Aug 16, 2008

  • 2 Answers

SOURCE: crankshaft position sensor 1999 dodge diesel

The easiest way to remove these crankshaft sensors is to pull the transmission out. They are in a very poor location and anyone with a moderate size hand has trouble pulling these out without pulling the transmission out. The vehicle will not run if this sensor is out, and i recommend replacing it even if it wasn't bad if you ever have to work on your transmission or ever have transmission work done. Knowing you have a Dodge, presuming it's an automatic, you will, and i repeat, will have to get transmission work done.

Posted on Dec 05, 2008

66 chrgr
  • 1011 Answers

SOURCE: Crankshaft position sensor location - 1991 Dodge Dakota 5.2L

it is on the passenger side on the back off the motor.there are two allen head bolts or 13mm.it goes into the transmission and normally has rubber at the opening.you should be able to gets this from the top follow middle of valve cover on pass. side the go strait back toward the fire wall.please rate this answer.

Posted on Jan 30, 2009

csmock132
  • 4669 Answers

SOURCE: Where is the crankshaft position

It is stuck in bellhousing of the transmission near the rear head. The new crank sensor will come with a piece of gasket paper on the end of the sensor. Install the sensor all the way in against the pick-up wheel. When you crank the engine the wheel will rip off the paper and the adjustment will be correct.

Posted on Mar 10, 2009

rvrfsh
  • 3 Answers

SOURCE: location of crankshaft position sensor

I have a 2005 neon and i found mu crank sensor on the radiator side of the block driver side of center directly below the starter. I hope this helps..

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing crankshaft position sencer on 2011 dodge cummings 6.7


Here's a link to a YouTube video showing location. The video is for a 5.9L, but it's the same for the 6.7L.
How to Change the Camshaft Position Sensor on Dodge Cummins 5 9 liter P0341

Nov 26, 2016 | Dodge Cars & Trucks

2 Answers

Where is the Crankshaft Position Sensor location on a Town and Country with the 3.6L V6 engine?


The role of the crankshaft position sensor is to determine the position of the crankshaft, the crankshaft angle. It is usually with a camshaft position sensor work together - to determine the basic ignition timing. Car Diagnostic Tool

Aug 27, 2016 | 2011 Chrysler Town and Country

1 Answer

Where is the crankshaft sensor on a 2001 frontier 4 wheel drive 3.3 engine?


Hi Lee,here's a link to a diagram to where your crankshaft position sensor is,just enlarge picture to see better.. GET 25 GIFT CARD FOR EVERY 100 SPENT ON ONLINE SHIP TO HOME ORDERS Here's another link to what the sensor look's like. Crankshaft Position Sensor at AutoZone com Best Crankshaft Position Sensor...

Nov 21, 2015 | 2001 Nissan Frontier Crew Cab

2 Answers

Where is located the crankshaft position sensor for 2005 dodge sprinter 2500


Is this a deisel motor? If so, it will not have a crankshaft sensor

Jul 19, 2015 | Dodge Cars & Trucks

1 Answer

How do i change the crankshaft position sensor


Hi Michael, The link below is a short YouTube video showing how to find a crank shaft position sensor on a (1998 dodge Dakota v8) I know it's not a 1998 dodge ram v8 but the motors should be similar, I hope this helped..........CHEERS..
https://www.youtube.com/watch?v=CfbYBb9GWhA
1998 dakota crank position sensor repair August 2011

Jun 12, 2015 | 1998 Dodge Ram 1500 4WD

1 Answer

Troubleshoot crank position sensor location


For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Nov 25, 2012 | 2000 Cadillac Escalade

2 Answers

Want to locate where is the crankshaft sensor on 2005 dodge grand carvan 3.3 eng


Hello brscwb,

Below is an image depicting the location of the crank sensor.

I hope this helps.

netvan_130.png

Regards,

natven

Aug 02, 2011 | Dodge Caravan Cars & Trucks

1 Answer

04 Dodge SRT 4 crankshaft sensor


The Crankshaft Position Sensor is located directly next to the starter.
  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Aug 15, 2008 | 2004 Dodge SRT-4

Not finding what you are looking for?
2007 Dodge Caravan SXT Minivan New Cars Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...