Question about 1991 Ford F350

1 Answer

Where is the turn signal fuse. It had a noise indicator when the turn signal was on, now it and the turn signals do not flash

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

I assume you are talking about a 1991 ford f350. if so i believe the blinker switch or blinker switch fuse is located on the fuse box underneath the dash board. you'll have to remove the dash board "belly pan" to gain access to the fuse box. the blinker fuse is a shiny square "odd" looking push in fuse. i believe it has a small aluminum casing on the fuse itself.

but....
it could also be a fuse relay witch is located under the hood on the driver's side fender well, but i'd check the blinker fuse first...

Posted on Jun 24, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1998 wrangler turn signal/brake light short

your socket may not be grounded properly, I have seen this before, and the simplest way to fix is change the socket with a new one.Not another used one it may also be bad.

Posted on Sep 06, 2008

  • 314 Answers

SOURCE: turn signal

Now replace the flasher unit! Frankster016

Posted on Oct 25, 2008

red54eyejp
  • 25 Answers

SOURCE: front driver side turn signal light doesn't flash

replace flasher......usually located in fuse block area...listen in this area....select passenger side ...then select driver side...you can hear flasher clicking...you have seperate flashers for each...FLASHERS are small cubes plugged into fuse block....probable bad driverside flasher

Posted on May 09, 2009

  • 3600 Answers

SOURCE: where is the fuse for the left turn signal on a 2007 Ford Freesty

replace the rear bulb it flashs fast to let you know the bulb is bad, whatever bulb is not flashing thats the bad bulb, should be a 1157 bulb or a 1156 if it has one contact it's a 1156 if two it's a 1157

Posted on May 24, 2009

  • 166 Answers

SOURCE: Turn Signals do not work - 1999 Cadillac Deville

flasher relay is corect

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chevy blazer . Problem is the horn does not work and turn signal flashes fast on both sides.


Do you know how to do automotive electrical testing ? Do you know what a relay is and how it works ? Turn signals flashing fast , could be aburnt bulb , flasher module .
VEHICLE RELAYS Operation Diagnosis
Turn Signal Lamps
The HAZ LP fuse in the underhood fuse block supplies battery positive voltage to the multifunction hazard switch assembly. The TURN fuse in the IP fuse block supplies Ignition positive voltage to the multifunction turn signal switch assembly. With the ignition switch in the RUN or START position, ignition positive voltage is connected through the multifunction turn signal and hazard switch assembly to the flasher module which is grounded at G205. When the turn signal switch is placed in either the left or right position, the circuit is complete from the flasher module to the turn signal lamps and to ground. The flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is activated, all turn signal lamps will flash including both IPC turn indicators. The front turn signals are grounded at G111 and G112. The rear turn signals are grounded at G475 and G422 on the pickup and G450 on the utility.

Aug 26, 2017 | Cars & Trucks

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

2 Answers

Turn singles and hazards are not working on my 2001 deville


I would replace the turn signal hazard combo switch.

Nov 28, 2016 | Cars & Trucks

1 Answer

Left turn signal doesn't flash.


there is a flasher under the dash put your 4 ways on and listen for the tick noise find the flasher unit under dash area driver side there is two one for the 4 ways and 1 for turn signals now that you have found them turn on working signal touch the flasher unit you will feel it pulse and hear the noise when you have the one pulseing on working signal this will need replacing can also be in fuse area have a good day

Nov 22, 2014 | 1990 Buick LeSabre

2 Answers

Tail lights not working


ck fuse for rear taillights tis under the dash lower left of steering wheel. or if you still have the manual look in there under fuses.
also look for a bad ground but i doubt that.. if it's both rear out.
fast flashing well here's a chart with all sorts of info.
Problem What To Do Turn signals light, but do not flash Replace the flasher No turn signals light on either side Check the fuse. Replace if defective.
Check the flasher by substitution.
Check for open circuit, short circuit or poor ground. Both turn signals on one side don't work Check for bad bulbs.
Check for bad ground In both housings. One turn signal light on one side doesn't work Check and/or replace bulb.
Check for corrosion in socket. Clean contacts.
Check for poor ground at socket. Turn signal flashes too fast or too slow Check any bulb on the side flashing too fast. A heavy-duty bulb is probably installed In place of a regular bulb
Check the bulb flashing too slow. A standard bulb was probably installed in place of a heavy-duty bulb
Check for loose connections or corrosion at the bulb socket Indicator lights don't work in either direction Check If the turn signals are working
Check the dash indicator lights
Check the flasher by substitution One Indicator light doesn't light On systems with 1 dash indicator:
- See if the lights work on the same side. Often the filaments have been reversed In systems combining stoplights with taillights and turn signals
- Check the flasher by substitution On systems with 2 Indicators:
- Check the bulbs on the same side
- Check the indicator light bulb
- Check the flasher by substitution
hope this helps. may want to print for future reference. :)
hope this helps.

Dec 31, 2017 | GMC Suburban Cars & Trucks

1 Answer

Turn signal and hazard lights not working at all. Replaced Hazard fuse relay. All bulbs are ok as indicated when alarm activated with key fob. All flash as indication doors are locked but the turn signals...


Most likely the cause of your problem is a flasher module. Usually it is found in the fuse box under the dash. But it can be on the back of the turning signal switch. If you are unsure, contact the service department of your manufacturer and ask them the location of the module. They will know immediately.

Feb 05, 2011 | 2001 Volkswagen Beetle

2 Answers

Turn signals dont work but bulbs work as flashers


your flasher element has gone out , it is on the fuse box read the cover and it will tell you which one it is replace

Aug 07, 2009 | 1995 GMC Jimmy

1 Answer

Rear turn signal indicator


There is a fuse under the hood in the fuse/relay box by the driver side fender marked LR TURN that is probably blown,each corner has own fuse.

Sep 11, 2008 | 2003 GMC Sonoma Extended Cab

Not finding what you are looking for?
1991 Ford F350 Logo

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...