Question about 2003 Hyundai Santa Fe
How to replace a coil for #6 cylinder on 2003 hyundai santr fe 2.7 liter v6
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2001 hyundai santa fe 6
OK. just follow the number on the ignition coils.
And the number on the cylinders are.
The FIREWALL side are 1,3,5, Starting from the belts location.
The RADIATOR side are 2,4,6, Starting from the belts location.
The coil with number 1 go to cylinder 1. as the same way the rest of the coils and cylinders.
OK... I hope this solve your question .
THank you for use fixya.
Posted on Jul 25, 2008
I have seen coil packs go bad on several Hyundai Accents, the coils will do exactly what they are supposed to (hence your check with an ohm meter), however, the coils short through the outer casing. Try running the car when it is dark out and spraying the coil packs with water. Listen for clicking and watch for arching from the coils to any metal around them. Look for abnormal detonation marks in the outer casing. My guess is you just need a set of new coils. If the Problem is worse in the rain then you have found your problem. Remember, If your car has been misfiring (as noted by the engine codes you listed), the EGR valve can become clogged and damage can be done to your catalytic converter as unburned fuel detonates inside it (keep an eye out for O2 codes in the future). Also, your new plugs can become fouled, be sure they are clean once you fix the problem. Checking your plugs can also be a useful indication of which cylinder is misbehaving.
Posted on Mar 18, 2009
Autozone.com says that for this vehicle the firing order is 1-2-3-4-5-6 and the set-up is 2/1 4/3 6/5 meaning that the #6 cylinder is far right on the back. It goes #1 #3 and #5 in the front and #2 #4 and #6 in the back.
Posted on Jul 19, 2009
Just take a picture of it with digital camera or phone. And start removing wires and hoses until they are all out of way of cover. Then remove the bolts all way around cover and pull straight up and it will come right off. If not use a flat head screw driver to prise it off. Clean old gasket off of valvecover and engine. then put it bak together. Tighten bolts slowly, start with ones in center ov it and work your way out. Just finger tight. Then snug, then torque em down. Not too tight as if tostrip the bolt or break it off. Cause it be very expensive. also write down everywhere each wire go's unless you can remember
Posted on May 11, 2010
Tips for a great answer:
Aug 15, 2015 | 1987 Buick Regal
Feb 24, 2015 | 1994 Chevrolet Camaro
Nov 14, 2014 | 2003 Hyundai Santa Fe
Apr 04, 2011 | 2003 Hyundai Santa Fe
Mar 29, 2010 | 2003 Hyundai Santa Fe
Jan 12, 2010 | 1992 Toyota Camry V6
Jul 18, 2009 | 2007 Hyundai Sonata Limited Sedan
Jun 15, 2009 | 2003 Hyundai Santa Fe
Jun 06, 2009 | 2003 Hyundai Tiburon
Nov 23, 2016 | 2003 Hyundai Santa Fe
13 people viewed this question
Usually answered in minutes!