Question about 2002 Chevrolet Cavalier Coupe

1 Answer

Remove camshaft Can't pull cam out but a inch acts like its stuck

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 957 Answers

Have you removed the lifters if you have then try turning it as you pull it out.

Posted on May 16, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have 1997 Ford explorer 5.0 Replacing camshaft synchronizer It's stuck


Help . Camshaft Sensor - Omfg ( Pics ) - Ford Explorer and Ranger ...

www.explorerforum.com > ... > Stock 1995 - 2001 Explorers
Oct 20, 2010 - 19 posts - ‎7 authors 98 Ford Explorer 2wd 5.0L .... If you're replacing the entire camshaft synchronizer, it gets a little more complicated. ... i would like to only be able to replace the sensor, but if its gonna get ... 1997 xlt v8 awd + 00,XLS .... taking care that the entire shaft comes out of the hole and isn't stuck to the oil pump shaft. Stuck cam position sensor shaft?
2 posts
Nov 24, 2013
Idler pulley squeaking
6 posts
Nov 16, 2012
Easy Camshaft Synchronizer Replacement
8 posts
Sep 11, 2012
Help Diagnose my intermittant Missing Problem
19 posts
May 23, 2004
More results from www.explorerforum.com

Replacing Camshaft Synchronizer & Sensor - Ford Mustang Forum

www.allfordmustangs.com > ... > V6 TecCamshaft Position Synchronizer Replacement - YouTube? 1:16https://www.youtube.com/watch?v=fXOJXnYIZQkNov 18, 2009 - Uploaded by 2003FordTaurus2003 Ford Taurus 3.0L Vulcan 181K miles with chirping sound ... does the shaft move out of its place when ...Camshaft Sensor/Synchronizer Replacement - Page 5 - Ford Tru

Nov 29, 2015 | Ford Cars & Trucks

1 Answer

How do I replace the valve cover gasket on a 2002 Saturn L200, 2.2 engine?


Disconnect the camshaft cover grounding strap.Right side of engine.
Remove ignition module, 4 bolts , and disconnect the electrical connection to it. Pull straight up to remove.
Remove 4 spark plugs.
Remove the coolant pipe bracket.
Remove the fuel line bracket.
Remove the 12 bolts holding down the cover, then pry up around the edges GENTLY to remove. You might want to use a rubber mallet at this stage, just don't overdo hitting it, its cast aluminum..
The gasket around the edge and around the spark plug holes don't need sealant, the new design does away with this.
Now would be a good time to check the wear on the Teflon timing chain shield between the camshaft sprockets.
Installation is in reverse order.
Camshaft cover bolts : Tighten to 89 INCH pounds.
Camshaft Ground Strap Bolt : 89 INCH pounds.
Spark Plugs : 15 FOOT pounds.
Ignition coil to camshaft cover bolts : 71 INCH pounds.
Coolant pipe AND Fuel line bracket bolts: 89 INCH pounds.
Good luck.

Feb 21, 2015 | 2002 Saturn L-Series

1 Answer

I need to take out a cam that stuck


If the cam stuck, you likely have ruined camshaft bearings causes by oil pressure issues. If you try to replace the camshaft, the replacement cam will likely seize up as well, or even break.
The only proper way to fix that is to get the engine out, remove the rear cam plug from the block and drive it forward out of the engine. Once it's out you can have a machine shop check the block for proper bore alignment and have new cam bearings installed. It's a lot of work. That's why most repair shops would rather replace the engine.
Even if you get the camshaft and bearings replaced, you still have to deal with why the first one seized.

Oct 15, 2014 | Cars & Trucks

1 Answer

Check engine light code p0014 exhaust and p0015 exhaust


P0015: Camshaft Position, Act B - bank 1, timing over

P0014: Camshaft Position, Act B - bank 1, timing over advanced
Check oil level and quality.
Remove n clean exhaust camshaft vanost actuator.
Do not refit to exhaust cam, but swap with inlet actuator.
clear codes...if eml on again see if fault moved to inlet cam. If so replace the actuator.

Jul 25, 2013 | 2007 Mini Cooper

1 Answer

Need diagram how to install timing chain 2004 Malibu overhead cam


Procedure is pasted below. Please let me know if you have questions.
Removal & Installation2.2L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    NOTE The timing chain has 2 matching colored links and 1 uniquely colored link.
    Negative battery cable, PCV hose, Fuel line bracket, Ignition coil and module assembly Ground strap from camshaft cover, Camshaft cover, Front fender liner, Accessory drive belt Crankshaft balancer pulley, Accessory drive belt tensioner, Front cover-to-water pump bolt Remaining front cover bolts, Front cover
  5. Rotate the engine until the crankshaft sprocket mark aligns with the matching colored link (2) at the 5 o-clock position.
  6. Confirm that the INT diamond on the intake camshaft sprocket is aligned with the uniquely colored link at (1) the 2 o-clock position.
  7. Confirm that the EXH triangle on the exhaust camshaft sprocket is aligned with the matching colored link (3).
  8. Remove or disconnect the following:
    NOTE Use a 24 mm wrench to hold the camshafts to prevent them from turning.
    Timing chain tensioner, Fixed timing chain guide access plug, Fixed timing chain guide Upper timing chain guide, Exhaust camshaft sprocket, Timing chain tensioner guide Intake camshaft sprocket, Timing chain through the top of the cylinder head Crankshaft sprocket

    jturcotte_638.jpg

    Fig. Lining up the crankshaft sprocket mark with the colored link in the 5 o-clock position (2).


    jturcotte_639.jpg

    Fig. Aligning the intake camshaft sprocket mark with the colored link in the 2 o-clock position (1).


    jturcotte_640.jpg

    Fig. Aligning the exhaust camshaft sprocket (3).

To install:
  1. Install the crankshaft sprocket with the timing mark in the 5 o-clock position.
  2. Assemble the intake camshaft sprocket to the timing chain with the timing mark lined up with the uniquely colored link (1). Hand tighten a new intake camshaft sprocket bolt.
  3. Lower the timing chain through the opening in the cylinder head.
  4. Route the timing chain around the crankshaft sprocket and line up the first marching colored link (2) with the timing mark on the crankshaft sprocket.
  5. Install the exhaust camshaft sprocket with a new bolt loosely onto the exhaust camshaft.
  6. Align the timing mark on the sprocket with the last matching colored (3).
  7. If necessary, align the camshaft as follows:
    1. Using a 24 mm wrench, first turn the intake camshaft until the alignment feature on the back of the camshaft sprocket seats in the notch in the front of the intake camshaft.
    2. Turn the crankshaft 45 degrees in either direction.
    3. Turn the intake camshaft to the appropriate location.
    4. Turn the crankshaft back to top dead center (TDC).
  8. When the sprocket seats in on the camshaft, tighten the sprocket bolt hand tight.
  9. Verify all of the colored links and the appropriate timing marks are still aligned.
  10. Install the fixed timing chain guide. Tighten the bolts to 133 inch lbs. (15 Nm).
  11. Install the upper timing chain guide. Tighten the bolts to 89 inch lbs. (10 Nm).
  12. Using a 24 mm wrench to hold the camshafts, tighten the camshaft sprocket bolts 63 ft. lbs. (85 Nm) plus 30 degrees.
  13. Measure the timing chain tensioner from end to end. A new tensioner should be supplied in the fully compressed non-active state. A tensioner in the compressed state will measure 2.83 inches (72 mm) front end to end. A tensioner in the active state will measure 3.35 inches (85 mm) from end to end.
  14. If the timing chain tensioner is not in the compressed state, perform the following steps:
    1. Remove the piston assembly from the body of the timing chain tensioner by pulling it out.
    2. Install the bottom half of the Tensioner tool J-45027-2 into a vise.
    3. Install the notch end of the piston assembly into the bottom half of the tensioner tool.
    4. Using the top half of the Tensioner tool J-45027-1, turn the ratchet cylinder into the piston.
    5. Install the compressed piston assembly back into the timing chain tensioner body until it stops at the bottom of the bore. Do not compress the piston assembly against the bottom of the bore.

  15. Install the timing chain tensioner assembly. Tighten to 66 ft. lbs. (75 Nm).
  16. Release the timing chain tensioner by compressing it approximately 0.08 inches (2mm). Feed a rubber-tipped tool down through the cam drive chest to reset on the cam chain. Give the tool a sharp jolt diagonally downwards to release the tensioner.
  17. Install the timing chain oiling nozzle.
  18. Install the timing chain guide bolt access hold plug with silicone sealant on the threads. Tighten the plug to 59 ft. lbs. (90 Nm).
  19. Install or connect the following:

    Camshaft cover. Tighten the bolts to 89 inch lbs. (10 Nm). Front cover with new gasket. Tighten the bolts to 18 ft. lbs. (25 Nm). Accessory drive belt tensioner. Tighten the bolts to 33 ft. lbs. (45 Nm). Crankshaft balancer pulley using a new bolt. Tighten the bolt to 74 ft. lbs. (100 Nm) plus 75 degrees. Accessory drive belt, Front fender liner, Ground strap to camshaft cover Ignition coil and module assembly, Fuel line bracket, Air intake assembly, Negative battery cable
  20. Refill the cooling system to the correct level.
  21. Refill the engine with oil to the correct level.
  22. Start the engine and check for leaks.

    jturcotte_2381.gif

    Fig. Compressing the timing chain tensioner-2.2L engine.

Oct 06, 2011 | 2004 Chevrolet Malibu

1 Answer

98 dodge stratus,engine light came on and it died and won't start now.What could be wrong?


when you crank the engine over now, does it sound different than before? if yes, you probably have a broken timing belt. it is also common for the cam gear to slip out of position from the cam and cause an incorrect, but hard to diagnose, timing issue. other no start with check engine light on issues could be a faulty cam or crank sensor.

pull the codes from the vehicles computer. if there is a cam or crank sensor code, or if there is a code that says in some different wording "cam sensor signal does not match crank sensor singal", first check crankshaft to camshaft timing. if belt is ok and timing marks line up then i strongly suggest removing the bolt from the camshaft that holds the cam gear on. with the bolt and cam gear removed you should be able to tell if the cam gear has rotated on the camshaft. there should be a small pin sticking out of the camshaft. if it is broken off then you need to replace the camshaft. if the pin is still there and the timing is good then replace iether the cam or crank sensor depending on what code you have stored in the ecu memory. if the code is not for the cam/crank sensor then google search the code number e.g. "p0502" and your make and model.

Mar 23, 2010 | 1998 Dodge Stratus

2 Answers

Replacing a camshaft position sensor on a 1998 cutlass


The cam sensor is integrated with the crank shaft sensor behind the crank shaft pulley. The 3.1 runs 2 crank sensors. the one behind the crankshaft pulley in integrated to act as a cam sensor. It has 2 sets on rings for that sensor, 1 is in use accustomed for the fuel timing
Good luck and hope this helps friend. 

Jul 14, 2009 | 1998 Oldsmobile Cutlass

1 Answer

Cant find cam sensor in 2004 dodge stratus r/t


2.0L 2.4L it is on The BACK OF the Cylinder Head REMOVAL
The camshaft position sensor is mounted to the rear of the cylinder head.

  1. Remove the negative battery cable.
  2. Disconnect the PCV hose and reposition.
    1. Disconnect electrical connectors from the camshaft position sensor.
    2. Remove camshaft position sensor mounting screws. Remove sensor.
      1. Loosen screw attaching target magnet to rear of camshaft and remove magnet.
      INSTALLATION
      The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.

      1. Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
      2. Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
      3. Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins.
      4. Connect the PCV Valve hose.
      5. Connect the negative battery cable.
2.7L V6
REMOVAL
The camshaft position sensor is mounted in the front of the head.
  1. Disconnect electrical connector from sensor.
  2. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
  1. Without pulling on the connector, pull the sensor out of the chain case cover.
INSTALLATION
The camshaft position sensor is mounted in the front of the head.

  1. Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
  2. Attach electrical connector to sensor.

Feb 12, 2009 | 2004 Dodge Stratus

1 Answer

Camshaft moves


all cams have end play. a measurment with the correct tool will give you an idea how much

Dec 30, 2008 | 1993 Ford Ranger SuperCab

1 Answer

Camshaft sensor


the cam sensor for 1999 jimmy with a 4.3L is in the distributer. pull off cap and rotor then unplug cam sensor and remove. please rate this answer

Nov 23, 2008 | 1995 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...