Question about Cars & Trucks

1 Answer

97 s10 4.3 v6 slave cylinder bleeding - Cars & Trucks

Posted by on

Ad

1 Answer

Same as bleeding brakes

Need a helper just like doing brakes

Posted on May 16, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1056 Answers

SOURCE: replaced clutch slave cylinder blew

Could be a couple of different things.
1) your clutch master has a plugged pressure bypass, and it is sending excessive pressure to the slave and blowing it out.
2) The clutch throw out arm is bound, and will not allow the slave to compress it.
3) The replacement slave was defective.

What was the reason for replacing the slave in the first place?

Posted on Jul 31, 2008

  • 275 Answers

SOURCE: Bleeding clutch slave cylinder

if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Posted on Nov 12, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

johnthejag
  • 286 Answers

SOURCE: bleeding the slave cylinder

Hi

Best to get the help of a friend to pump the clutch pedal for you.

Take care with the brake fluid, as it removes paintwork !

Top up your clutch fluid reservoir, connect a bleeding tube to the nipple on your slave cylinder, and put the other end of tube in a container.

Get your friend to pump pedal 3 times, and then hold to the floor.

Open the nipple for 5 seconds or so, then close.

Repeat this about 6 to 8 times topping up the fluid as you go.

You should then find, that the air is out of your system, and your pedal is back to normal !

Good luck !

A FixYa rating would be nice.... Thank you ! John.



Posted on Feb 10, 2009

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced throw out bearings on 1996 dodge Dakota/ v6,do i bleed clutch also,if so how.


if the slave cylinder remaine intact on the hose from the master cylinder then there is no need to bleed the system
if the slave cylinder was inside the bell housing and you ahd to remove a hose to get the box out then yes it has to be bled and by the bleed niple on the sode of the bell housding
bleeding procedure is as per any hydraulic system

Jul 07, 2015 | Dodge Cars & Trucks

1 Answer

Hello i have a 1993 chevy cheyyenne k1500 pickup with a v6 4.3 its a manual and my clutch line broke off of my slabe cylinder due to a crack in it from ware and tear which leaked fluid all out and lost...


I changed the slave cylinder on my 97 Accord and all I did was disconnect the lines, disconnect the linkage from the pedal, move some stuff to get it out, hook up the new one, fill with fluid, and bleed the line to the clutch cylinder. Point is, if you have to remove the slave cylinder, that's fine. You'll have to bleed the system anyway. Like bleeding brakes. I didn't have to drain any "tranny fluid" as the clutch fluid was a separate system. Had a drain pan underneath to catch fluid.

May 30, 2017 | Chevrolet Cars & Trucks

1 Answer

How do u bleed a hydryalic clutch on a 97 firebird formula


Hi Rick,again,here's a link to bleeding your clutch,if your fluid is low,then your slave cylinder may be bad. Repair Guides Clutch Actuator slave Cylinder AutoZone com

Sep 08, 2014 | 1997 Pontiac Firebird

1 Answer

How do I bleed the master cylinder and slave cylinder they are together on a 92 Chevy half ton 2 wheel drive v6 5 speed I had to replace do to cracked master cylinder


If its already on the car and connected you, can only bleed it by bleeding the wheel cylinder/calipers. Its always much easier to bleed it on the bench befroe you install it.

Aug 29, 2014 | Cars & Trucks

1 Answer

How to bleed a slave cylinder on a 97 acura


You should not be bleeding the brake system if you don't know how . It is a very precise procedure and you should not operate the car until you have qualified help.. It can't be done by yourself you need help to bleed the system unless you have a DBR scan tool.

Jan 03, 2014 | Cars & Trucks

1 Answer

94 Chevy S10 Blazer


If you need to bleed the clutch, you should notice a soft clutch pedal getting firmer when you pump it (the air that you need to bleed out of the system compresses as you pump, and the pedal gets firmer, just like brakes).

A hydraulic system for a clutch (or your brakes) has a master cylinder component and a slave cylinder component. If you compress fluid in the master cylinder, it exerts force on a (more than one for your brakes) slave cylinder that causes a mechanical component to move.

Recommend you lean into the engine compartment on the drive side at the firewall or crawl under the car and have someone depress and release your clutch a few times. You should be able to find the master cylinder because the mechanical clutch linkage has to be attached to it. The same at the bellhousing, where the slave cylinder has to mechanically cause the throwout bearing to be moved. It is possible (but not probable) that your clutch master cylinder is located on the inside of the firewall, not the outside.

Nov 07, 2013 | Cars & Trucks

1 Answer

How to bleed the clutch on a saturn 97


one way to bleed it is by pulling the piston like slave cylinder with the rod out of the transmission and by pushing the rod into the slave cylinder several times, make sure you have plenty of dot3 brake fluid in the clutch master slave before you do this. by pushing the rod into the slave cylinder it acts like doing a brake job it bleeds the air out into the clutch master slave cylinder and sucks in the break fluid getting rid of all air in the system. thats the only way to bleed those systems seeing as they are sealed systems

Aug 22, 2010 | 1997 Saturn SL

1 Answer

I'm trying to bleed my hydraulic clutch on a '86 fiero V6 4 speed where's the bleeder screw?


Look at the air cleaner and find the big hose that goes to the throttle body. The clutch slave cylinder is an inch or two right below the air cleaner side of the giant hose. There is a heat shield over the half of the slave cylinder near the exhaust crossover pipe. The bleeder screw is at the driver's side end of the slave cylinder.

Good luck,

Rebel Faggioli

Feb 12, 2010 | 1986 Pontiac Fiero

1 Answer

Fitted new clutch and slave cylinder in 2.5 v6


crawl up under the dashboard & look where the clutch pedal rod goes through the firewall. look for traces of brake fluid at the rubber boot of the rod. a clutch master cylinder normally will leak to the inside of the vehicle & down the firewall when it fails. Replace as required & bleed clutch system using the bleeder valve that should be on the slave asy.

Oct 15, 2009 | 1998 Ford Contour

1 Answer

I changed the clutch master cylinder and the clutch slave cylinder on my 97 sidekick and I still have no pedal


did you bleed the air out of the slave cylinder. Do this by having a buddy sit in the car pump this pedal a couple of time and then hold it to the floor then open the bleeder valve on the slave cylinder. repeat until just fluid comes of or the bleeder valve. refill slave to proper level with recommend brake fluid. hope this helps.

Jul 08, 2009 | 1997 Suzuki Sidekick

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...