Question about 1994 Land Rover Discovery

1 Answer

Repair tweed heads

Replace drive belt for power steering on discovery petrol v8i 1993

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 189 Answers

Posted on Jun 14, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: I need to replace the fan belt. Which pulleys does it go around?

Hi there,

My brother in law and I changed it without taking anything apart except the fan cover, what you'll need to do is gently use a crobar to release the tensioner pully directly below the alternator, and jam it a bit, then slowly release the old belt, if it's as worn as mine was you'll be fine. Then simply run the new belt starting from the bottom up. There's a great diagram on the weblink below.

http://www.roverparts.com/TechTips/serpentine_belt_routing_D2.cfm

Posted on Feb 15, 2009

  • 4336 Answers

SOURCE: how do i change the alternator belt on a 1993 land

WEll, sorry, but the impeding belt would need to be removed first. I suggest that all belts be changed during this type of event, you do not want to go back in, again.

Posted on Dec 11, 2009

  • 30 Answers

SOURCE: CAN I HAVE WIRING DIAGRAM FOR LAND ROVER DISCOVERY

the easiest and in-expensive way would be to go to your local library. You should find what your looking for in the auto reference section. Or, you can buy the publications on ebay, at Auto Zone, or O'Reallies.

Posted on Apr 25, 2010

01fordeb
  • 1033 Answers

SOURCE: land rover discovery 1996 V8i engine firing order

1-8-4-3-6-5-7-2

Posted on Jun 22, 2010

  • 16 Answers

SOURCE: My Discovery 1 V8i is

look under the bonnet at night with the engine running see if the coil is sparking around the top or are the ignition leads sparking all over the place DO NOT TOUCH ANYTHING HT VOLTAGE CAN KILL if there are sparks around the coil top change it and the plugs and leads if the problem persists check the distributor please take the time to rate this if it helps

Posted on Aug 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.1 1993 chevy lumina cam sensor position? And how to take out


  • SERVICE AND REPAIR

Camshaft Sensor Follow this URL for picture:_
http://alldatapro.com/alldata/PRO~V416324719~C30660~R0~OB0~P3R0H~N/0/41746052/42417623/42417638/42422763/34853741/34857029/34857030/101366976/14461280/42437587/41882479

REMOVE OR DISCONNECT
  • Negative battery.
  • Serpentine drive belt and secondary air injection drive belt.
  • Power steering pump.
  • Electrical connector.
  • Bolt (1). Refer to Figure.
  • Camshaft sensor.
INSTALL OR CONNECT
  • Camshaft sensor.
  • Bolt (1) torque to 10 Nm (8 ft lb).
  • Electrical connector.
  • Power steering pump.
  • Serpentine drive belt and secondary air injection drive be!t.
  • Negative battery cable.

May 04, 2015 | 1993 Chevrolet Lumina

1 Answer

I have issues with belt squealing on Suzuki swift. The car is a 2005 (new model) 1.3 petrol. Just before Christmas the original 9 year old belt started to squeal and snapped, I replaced the belt and s


belts squeal for only 2 reason
it's bad. the belt.
or the accessorym it drives is Seized.

i guess you never head of a 5buck stethoscope
and listen to the accessory bearings, ah, alternator front and rear
i hear, front crying for help. easy as child play.
sold everywhere cars parts are sold.

there is no need to guess, , answer use tools.
this was true in 1920 and now, belts then and now all can squeal.
in the old days we had many belts and could drop them
then comes, SERP belts. one for all.
we dont have 1.3 swifts here, so cant see belt routing.

http://www.fixkick.com/tools/steth1.jpg

Feb 01, 2015 | 2005 Suzuki Swift

1 Answer

How to replace drive belt for power steering pump on discovery1 1993 v8i


Try this video:

http://www.youtube.com/watch?v=e8uojR0WZjU

May 16, 2014 | 1994 Land Rover Discovery

1 Answer

Rpm 30 mph


IF you are on lpg then check that the gas regulator for icing up and stopping the liquid LPG from turning to gas. If it cuts out on petrol check that there is not a problem with the petrol shut off solenoid . Check the LPG cut off solenoid . I suspect a loose connection or wires to either or both or faulty units

Dec 02, 2013 | Land Rover Cars & Trucks

1 Answer

Um,dumb question perhaps, but where is the fuel filter housed on a 1993 Landrover Discovery v8i?


Land Rover did not sell a Discovery in the USA in 1993 so I can't help you there.
Usually they are in the fuel line under the truck between the gas tank and the engine.

Sep 14, 2012 | Cars & Trucks

1 Answer

I have a 1993 callidac and the power steering pump is gone out can i bypass it with the regular belt or do i need a different belt


You cannot drive this car without a functioning power steering as it would be almost impossible to steer. Therefore you cannot bypass the pump. Replace the defective P/S pump.

Sep 11, 2010 | 1993 Cadillac DeVille

2 Answers

Looking to see haw difficult it is to change power steering pump.? any ideas Iam some what mechanicaly inclined


GM Astro/Safari 1985-1996 Repair Guide
Power Steering Pump - REMOVAL & INSTALLATION
(see Figures 1, 2, 3, 4, 5, 6 and 7)

199f8a3.jpg

Fig. 1: Exploded view of the power steering pump assembly mounting-2.5L engine

1544b7a.jpg

Fig. 2: Exploded view of the power steering pump assembly mounting-early-model 4.3L engine

8c93529.jpg

Fig. 3: Removing the power steering pump pulley-1985-92 vehicles

1995aea.jpg

Fig. 4: Installing the power steering pump pulley

d000dbb.jpg

Fig. 5: Pump pulley removal and installation-1993-96 vehicles

e8e94e6.jpg

Fig. 6: Exploded view of the power steering pump mounting-late-model 4.3L engines (1993-96 shown)

44caf14.jpg

Fig. 7: Typical power steering pump hose routing-1996 shown


The following procedure requires the use of the GM Puller tool No. J-29785-A (1985-92), Puller J-25034-B (1993-96) or equivalent, and the GM Pulley Installer tool No. J-25033-B or equivalent.
  1. Disconnect the negative battery cable for safety.
  2. For 1996 vehicles, remove the air cleaner assembly for access.
  3. For 1993-96 vehicles, remove the hood latch and the upper fan shroud.
  4. Release tension and remove the drive belt.
  5. Remove the power steering pump pulley using a suitable puller tool.
  6. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  7. Position a fluid catch pan under the power steering pump.
  8. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
WARNING Be sure to cap all openings in the pump hydraulic system to prevent excessive fluid spillage and the possibility of system contamination.
  1. Remove the power steering pump from the vehicle.
To install:
  1. Position the pump to the vehicle, then uncap and connect the pump hoses.
  2. Install the steering pump to the retaining bracket, then secure using the retaining bolts. Tighten the power steering pump-to-bracket bolts to 37 ft. lbs. (50 Nm). For 1996 vehicles, tighten the nut to 30 ft. lbs. (41 Nm).
On early-model vehicles where the drive belt is tensioned by pivoting the power steering pump assembly, do NOT fully tighten the mounting bolts at this time, since you will just have to loosen them again for belt installation and adjustment.
  1. Install the pump pulley using the GM Pulley Installer tool No. J-25033-B or equivalent. Press the drive pulley onto the power steering pump.
  2. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  3. Install the drive belt. On early-model vehicles so equipped, properly adjust the belt tension. For details on belt installation and tension adjustment.
  4. For 1993-96 vehicles install the upper fan shroud and the hood latch assembly.
  5. For 1996 vehicles, install the air cleaner assembly.
  6. Connect the negative battery cable.
  7. Refill the power steering reservoir and bleed the power steering system.
  8. Remove the jackstands and carefully lower the vehicle.
  9. Road test the vehicle, then check and top-off the power steering fluid.

hope this help (remember rated this post) Good luck.

May 13, 2010 | 1989 GMC Safari

1 Answer

I need to replace the fan belt. Which pulleys does it go around?


Hi there,

My brother in law and I changed it without taking anything apart except the fan cover, what you'll need to do is gently use a crobar to release the tensioner pully directly below the alternator, and jam it a bit, then slowly release the old belt, if it's as worn as mine was you'll be fine. Then simply run the new belt starting from the bottom up. There's a great diagram on the weblink below.

http://www.roverparts.com/TechTips/serpentine_belt_routing_D2.cfm

Dec 27, 2008 | 1996 Land Rover Discovery

Not finding what you are looking for?
1994 Land Rover Discovery Logo

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7727 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...