Question about 2005 Opel Astra 1.4

3 Answers

Oil light on after engine warm-up on idle

Engine reaches operating temperature & @ idle rpm oil light comes on.increase revs & it goes out

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 71 Answers

Normally due to low oil level. 2.75 QTS low from 5 qtswill make oil pump not be able to produce enough pressure. But is engine reved to four grand and kept there, should also make oil pressure drop after a while causing light to come on. If engine was designed for 10w-40 and u use 5-30 or synthetic 0w-20, then oil pressure may bebe low. Locate oilpress switch remove and install manual gauge. If pressure is below the 3-5 psi cut off pressure then you have major problems. Change oils and filter. If switch is located in oil Gally after the filter then oil filter could be plugged. Author way needs changed. What type and year are we working on?

Posted on May 16, 2014

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 57 Answers

Low oil pressure. check the level, too low and low pressure light comes on. Too low viscosity (eg 5-20) also can make it come on. If it is a high mileage engine, the pump is old and the guides are worn so oil escapes around seals and lowers the pressure, even if it is not apppearing to burn any.

Posted on May 15, 2014

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Opel Master
  • 808 Answers

This means a mechanical gauge test is required to check actual pressure warm idling if low below 20 psi then the oil pressure pump relief is stuck open or engine bearing are worn

Posted on May 15, 2014

  • Dan Jacobs
    Dan Jacobs May 19, 2014

    After reading one life 728 reply No lets talk about how pressure is made. #1 take a garden hose turn on water as high as it will go it will run out the end and go about 2-3 feet in front of you. The city water pressure lets say it is 30lbs. Now install that brass fire hose nozzle How far will the water go now about 3 times farther with the same pressure. So now in the engine at a given speed the oil pump pumps oil (not pressure) So if the suction side has no leaks (low oil, broken gasket on suction pipe ) That is all it does pumps oil through the filter and to the engine bearings where the clearance between the crankshaft and bearings (the fire nozzle) creates resistance to make pressure once this pressure becomes to great at any speed the oil pump has a pressure relief valve that opens and put excess oil back into the oil pan or suction side of the pump. a restricted oil filter will also cause this problem if the sending unit is after the filter. But clearance issues is the #1 concern bearings on main and rod bearings camshaft or broken oil squirters for the timing chain yes thicker oil keeps a higher pressure do to it takes up space until heated .

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Speedometer


I take it that you only have 1 speedometer and that reads miles per hour or car speed . The left speedo? is in reality a tachometer and reads the engine revolutions per minute. When the engine is cold (before it reaches operating temperature) the CPU will keep the rpm's above 1000 (1 x1000) and when that temperature is reached the idle speed is reduced to normal operating rpm's. So yes it is normal. All you need to do is know the difference and the meaning of all the gauges.

Oct 23, 2013 | 2001 Honda Accord

1 Answer

I have a 1984 ford f150. The truck idles very high when in park but when you put in drive or reverse it goes down to normal. It has duel straight exhaust on it and I wonder if that could be the prob. Idk.


you didnt say if it was happening only during the initial warm up of the vehicle or all the time. if it is just during warm up this is not too unusual as long as the engine isnt racing. if it is just a "high idle", say arround 2,000 rpm's its normal. the idle would usually go down as the vehicle reaches operating temperature. when you put the vehicle in gear, you are actually loading the engine slightly, thats why the idle comes down then. when in park the engine has no load on it so it is free to rev a little higher at these times. if it a at a high idle constantly, then i would start looking for sticking throttle cable, binding throttle plates, ect and remedy the problem. this should not have anything to do with the dual exhaust.

Mar 13, 2011 | Ford F-150 Cars & Trucks

1 Answer

When i start my toyota corolla small body in the morning, the idling goes up to 2000rpm, why is that so?


It is quite common for most cars to have an increased rev range when a engine is started from cold, as the temperature increases the revs will drop down.
Depending on the age of the car has a lot to do with it also, as older cars used an auto choke system until a warmer temperature was attained.
More modern cars don't neccessarily need extreme higher revs, but still operate with a thermostatic controller, that regulates the fuel flow via the fuel injection system.
before you do anything, consider
1/ You have to know also what rev range does the car operate at when its been running for a while, eg when its warm and idling does it rev at 600,800,1000.
2/ Make sure you don't have your air conditioner on when starting, as this increases revs also.
3/ How long is the increased revs lasting.
4/ Is this car a carburated model or fuel injection
5/ have a visual and check that there are no small vacuum pipes that have come off anywhere around the intake area of the motor. (Intake area can be found where you accelorator cable ends up.
6/ failing that when your car goes for its next service, bring this problem to the mechanics attention.
it can be difficult to diagnose problems like these unless your looking at the engine.

I hope this has helped somewhat

kazont69
I hope this

Feb 01, 2011 | Toyota Corolla Cars & Trucks

1 Answer

Oil light on at stop


engine oil pressure may be low remove oil pressure sending unit and install a pressure gauge check for pressure while warm if pressure is ok replace oil pressure sending unit oil pressure at idle should be between 5-15 psi at min

Nov 17, 2009 | 2006 Dodge Stratus

3 Answers

Oil Pressure Light Comes On after 10 min of Driving


You may not have put the right amount of oil in your car, your oil pressure sensor could be faulty, or you may have a leak.

By revving your engine, you're increasing the pressure and thus turning off the light and making the sensor think that it's at the correct pressure.

Sep 08, 2009 | 1998 Chevrolet Malibu

1 Answer

The engine will not idle when cold


possibly the coolant temperature sensor is faulty

Sep 05, 2009 | 1995 Subaru Legacy

1 Answer

Oil light in 1999 Toyota camry comes on when idling.


bad to worn out oil pump or excessive oil passage clearances that allowing more oil to pass thru them at a lower pressure due to the bigger opening. It can be a sign of an emminant engine failure due to oil starvation.

Aug 04, 2009 | 1996 Toyota Camry

1 Answer

Oil light comes on under load but goes out when shifting gears & while idling


conikelane: When you describe the light coming on under load, you when you have put the engine to work by bringing the RPM's above idle.
When you are at a standstill, the engine is at idle. when you start going, the engine speed increases and that is when the oil light goes on. When you go to shift gears, the light goes out momentarily.The reason it goes out is that the engine is dropping while you shift gears. From your description, you have a problem with oil starvation from the pickup tube in the oil pan in all likelihood.
I would bet you that if you pulled the oil pan, you would find that the screen on the pickup tube was nearly clogged up with sludge allowing only a small area for the oil to pass through which is why as the engine speed increases and the oil pump tries to pull more volume through the small opening, it starves for oil and it can not deliver what the engine needs thus causing the light to go on.

Jul 14, 2009 | 1999 Mercury Tracer

1 Answer

Xterra repair


Since this is an intermittent problem, first try to determine if the problem arises due to one of these many intermittent problems:

* Vehicle vibration
* Heat sensitive
* Freezing
* Water intrusion
* Electrical load
* Cold or hot start up

If you can't isolate the cause of the intermittent problem, you can try adjusting the Idle Speed/Ignition Timing/Idle Mixture Ratio:

Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment

PREPARATION
1) Make sure that the following parts are in good order.

* Battery
* Ignition system
* Engine oil and coolant levels
* Fuses
* ECM harness connector
* Vacuum hoses
* Air intake system
* (Oil filler cap, oil level gauge, etc.)
* Fuel pressure
* Engine compression
* EGR valve operation (If so equipped)
* Throttle valve
* Evaporative emission system

2) On air conditioner equipped models, checks should be carried out while the air conditioner is OFF.
3) On automatic transmission equipped models, when checking idle rpm, ignition timing and mixture ratio,
checks should be carried out while shift lever is in “N” position.
4) When measuring “CO” percentage, insert probe more than 40 cm (15.7 in) into tail pipe.
5) Turn off headlamps, heater blower, rear defogger.
6) Keep front wheels pointed straight ahead.
7) Make the check after the cooling fan has stopped.

INSPECTION PROCEDURE

1 INSPECTION START
1. Visually check the following:
I Air cleaner clogging
I Hoses and ducts for leaks
I EGR valve operation (If so equipped)
I Electrical connectors
I Gasket
I Throttle valve and throttle position sensor operation
2. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
Ensure engine stays below 1,000 rpm.
3. Open engine hood and run engine at about 2,000 rpm for about 2 minutes under no-load.
4. Perform diagnostic test mode II (Self-diagnostic results).
OK or NG
OK ' GO TO 2.
NG ' 1. Repair or replace components as necessary.
2. GO TO 2.

2 CHECK IGNITION TIMING
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Turn off engine and disconnect throttle position sensor harness connector.
4. Start and rev engine (2,000 - 3,000 rpm) two or three times under no-load, then run at idle speed.
5. Check ignition timing with a timing light.
15°±2° BTDC (in “P” or “N” position)
OK or NG
OK ' GO TO 4.
NG ' GO TO 3.

3 ADJUST IGNITION TIMING
1. Adjust ignition timing by turning distributor after loosening securing bolts.
2. Turn off engine and connect throttle position sensor harness connector to throttle position sensor.
' GO TO 2.


4 CHECK BASE IDLE SPEED
1. Check idle speed.
700±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 6.
NG ' GO TO 5.

5 ADJUST BASE IDLE SPEED
1. Rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run engine at idle speed.
2. Adjust idle speed by turning idle speed adjusting screw.
700±50 rpm (in “P” or “N” position)
' GO TO 6.

6 CHECK TARGET IDLE SPEED
1. Turn off engine and connect throttle position sensor harness connector.
2. Start and rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run at idle speed.
3. Check idle speed.
750±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 9.
NG ' GO TO 7.

7 DETECT MALFUNCTIONING PART
Check the following.
1. Check IACV-AAC valve and replace if necessary.
2. Check IACV-AAC valve harness and repair if necessary.
3. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 9.

9 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
3. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 12.
NG (MIL does not blink.) ' GO TO 17.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.


10 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 13.
NG ' GO TO 11.

11 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit.
Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.


13 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
2. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG (MIL does not blink.) ' GO TO 16.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor RH.
2. GO TO 14.


14 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG ' GO TO 15.

15 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit. Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.
16 CHECK FRONT HEATED OXYGEN SENSOR RH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor RH harness connector.
4. Check harness continuity between ECM terminal 50 and front heated oxygen sensor RH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

17 CHECK FRONT HEATED OXYGEN SENSOR LH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor LH harness connector.
4. Check harness continuity between ECM terminal 51 and front heated oxygen sensor LH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

18 PREPARATION FOR “CO” % CHECK
1. Disconnect engine coolant temperature sensor harness connector.
2. Connect a resistor (4.4 kW) between terminals of engine coolant temperature sensor harness connector.
' GO TO 19.

19 CHECK “CO” %
1. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Check “CO” %.
Idle CO: 1.5 - 9%
After checking CO%,
a. Disconnect the resistor from terminals of engine coolant temperature sensor.
b. Connect engine coolant temperature sensor harness connector to engine coolant temperature sensor.
OK or NG
OK ' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.
NG ' GO TO 20.

20 DETECT MALFUNCTIONING PART
Check the following.
1. Connect front heated oxygen sensor harness connectors to front heated oxygen sensors.
2. Check fuel pressure regulator.
3. Check mass air flow sensor and its circuit.
4. Check injector and its circuit.
Clean or replace if necessary.
5. Check engine coolant temperature sensor and its circuit.
6. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.

Aug 17, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
2005 Opel Astra 1.4 Logo

630 people viewed this question

Ask a Question

Usually answered in minutes!

Top Opel Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Brad Brown

Level 3 Expert

15673 Answers

george parkes

Level 3 Expert

975 Answers

Are you an Opel Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...