Question about 1995 Ford Ranger Supercab

Open Question

Exhaust manifold torque

2.3L

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm installing a 2.2 in a 2003 Oldsmobile Alero and I'd like to know the torque specs on the Exhaust bolts and studs. Thanks


Exhaust Manifold To Cylinder Head - 9.58 ft lbs
Exhaust Pipe To Exhaust Manifold - 20 ft lbs
you can check it out here, also all other torque specs for your engine.
Torque Specs Database

Feb 23, 2015 | 2003 Oldsmobile Alero

2 Answers

2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


  1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

Oct 20, 2011 | 2000 Daewoo Lanos

1 Answer

Torque spec on exhaust manifold for 2000 yukon xl


EXHAUST MANIFOLD BOLT TORQUE 2000 GMC Truck Yukon XL 1500 2WD 5.3L SFI 8cyl The Exhaust Manifold Bolt Torque

Exhaust manifold bolts (first pass) 11 Lb/Ft.Exhaust manifold bolts (final pass) 18 Lb/Ft.Exhaust manifold nuts 39 Lb/Ft.Exhaust manifold stud 16 Lb/Ft.Air injection reaction (AIR) Pipe to exhaust manifoldnuts 18 Lb/Ft.(AIR) Pipe to exhaust manifold studs 4 Lb/Ft.Exhaust manifold AIR pipe studs 4 Lb/Ft.Note:To torque bolts and nuts, start in center usingcrisscross pattern working outward.

May 07, 2011 | GMC Yukon XL Cars & Trucks

2 Answers

2004 ford escape exhaust manifold torque specs?


2b507d0.jpg

Fig. Left side exhaust manifold bolt torque sequence-3.0L engine


22ac5ae.jpg

Fig. Right side exhaust manifold bolt torque sequence-3.0L engine

Both cases, exhaust manifold and new gasket, torque the bolts to 15 ft. lbs. (20 Nm).

Good luck (remember to rate this answer).

Oct 22, 2010 | 2004 Ford Escape

1 Answer

Where are the four O2 sensors on a 2003 Montero Sport? Is $300 reasonable to replace the two upstream sensors?


According to the service literature I read, the 2003 Montero Sport with the 3.0 or 3.5 L engine does not have O2 sensors listed even in the maintenance schedule. The 2.4 L engine has it on the exhaust manifold though.
---
However, the following lists the par, though for before or after the catalytic converter:

http://www.partstrain.com/store/index.php?VN=4294967180+4294966587+4294964143+&Nr=AND(universal:0)&N=0&Ntt=Oxygen%20Sensor

---
I think that $250 to $300 is reasonable if the Oxygen sensors are stuck in there with rust and the threads are preserved by the technician. Oxygen Sensor replacement can be tricky.
---
Good luck on this repair.

Exhaust Manifold

REMOVAL & INSTALLATION

2.4L Engine


  1. Remove or disconnect the following:

    • Negative battery cable

    CAUTION
    Wait at least 90 seconds after the negative
    battery cable is disconnected to prevent possible deployment of the air bag.


  2. Heat cowl from the exhaust manifold
  3. Aspirator valve assembly, if equipped
  4. Oil dipstick and guide
  5. Oxygen (O2S) sensor connector and ground cable, if equipped
  6. Exhaust pipe from the manifold
  7. Exhaust manifold and gasket from the engine
    To install:

  8. Install or connect the following:

    • Exhaust manifold. Torque the M8 mounting nuts to 22 ft. lbs. (29 Nm) and the
      M10 mounting bolts 36 ft. lbs. (49 Nm). starting from the middle and working
      outward.
    • O2S sensor connector and ground cable, if equipped
    • Exhaust pipe to the manifold. Torque the nuts to 35ft. (49 Nm).
    • Aspirator valve assembly, if removed
    • Heat cowl to the exhaust manifold. Torque the bolts to 117 inch lbs. (13
      Nm).
    • Negative battery cable

  9. Start the engine and check for exhaust leaks.


3.0L and 3.5L Engines


  1. Remove or disconnect the following:

    • Negative battery cable
    • Exhaust pipe from the exhaust manifolds
    • Oil dipstick, guide and O-ring
    • Heat shields
    • Exhaust manifolds

  2. Clean the gasket mounting surfaces. Inspect the manifolds for cracks,
    flatness and/or damage.
    To install:

  3. Install or connect the following:

    • New gasket and exhaust manifold. Torque the nuts to 33 ft. lbs. (44 Nm) on
      3.0L engines and 22 ft. lbs. (29 Nm) on 3.5L engines.
    • Heat shield, Torque the bolts to 10 ft. lbs. (14 Nm).
    • Exhaust pipe to the exhaust manifolds. Torque the nuts to 35ft. (49 Nm).
    • Oil dipstick, guide and new O-ring
    • Negative battery cable

  4. Start the engine and check for exhaust leaks.


prev.gif next.gif

Oct 07, 2010 | 2003 Mitsubishi Montero Sport

1 Answer

How is the manifold removed on 2005 lincoln ls? Where is the bolt that holding it down?


Exhaust Manifold - Removal & Installation3.0L Engine
  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Remove or disconnect the following:
    Negative battery cable Heat shields Lower splash shields Exhaust front pipes Secondary air tubes Exhaust Gas Recirculation (EGR) tube Exhaust manifold

To install:


3ba09f1.jpg
Fig. Right exhaust manifold torque sequence-3.0L engine


d78e7f5.jpg
Fig. Left exhaust manifold torque sequence-3.0L engine
  1. Install the exhaust manifolds. Tighten the fasteners in sequence as follows:
    1. Step 1: 15 ft. lbs. (20 Nm)
    2. Step 2: 15 ft. lbs. (20 Nm)
  2. Install or connect the following:
    Exhaust Gas Recirculation (EGR) tube Secondary air tubes Exhaust front pipes Lower splash shields Heat shields Negative battery cable
  3. Start the engine and check for leaks.

continue...

Jun 21, 2010 | 2002 Lincoln LS

1 Answer

Torque for 2004 hummer h2 exhaust manifold bolts


Exhaust manifold bolts-first pass 11 Lb/Ft. Exhaust manifold bolts-final pass 18 Lb/Ft. Exhaust manifold heat shield bolts 7 Lb/Ft. Note: To torque bolts & nuts, start in center using crisscross pattern working outward

Apr 26, 2010 | 2004 Hummer H2

3 Answers

Need head bolt, intake manifold, and exhaust torque specs


Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Mar 06, 2010 | GMC Suburban Cars & Trucks

2 Answers

How to replace the water pump on 1993 oldsmoblie achieva.


2.4 enigine is the harder of the 3 enignes. it will need a timing chain to be removed and a coolant tube in the back of the engine to be removed. this job on the book calls for almost 7 hours.

if its 3.3 or 3100 its alot easier.

3100 is just 4 10mm pulley bolts and 5 or 6 small 8mm water pump bolts.

3.3 is alittle more work, but same concept as 3100 engine. more owkr only cause its in a tighter area.

good luck,
michael

Apr 29, 2009 | Oldsmobile Achieva Cars & Trucks

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...