Question about 2001 Ford Taurus

2 Answers

Seat belts Can I take a back seat belt and move it to the drivers seat belt till my replacement comes in It is a 2001Taurus

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Seats are bolted down pretty good and the back seat is two pieces the bottom and the back. So you wouldn't be able to use the seat belt fr the back unless you plan on breaking the back seats. I wouldn't recommend it.

Posted on May 17, 2014

Only a dealers parts dept
can answer that

Posted on May 15, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 141 Answers

SOURCE: back seat belt replacement

Due to this being a safety item all parts and install must be completed by the dealer.

Posted on Jan 15, 2009

  • 7 Answers

SOURCE: seat belt not retracting

retract spring is broken.

Posted on Feb 09, 2009

  • 9 Answers

SOURCE: seat belt alarm goes off when belt is buckled

try relapsing the switch inside the female of the seat belt

1024d1201421548-seat-belt-alarm-seatbelt-pretensioner.jpg

Posted on Apr 17, 2009

scott_77
  • 48 Answers

SOURCE: 1) Seat belt is stuck 2)Check engine light

Sometimes you need to reset the computer. Try disconnecting the battery.

Posted on Apr 30, 2009

  • 1382 Answers

SOURCE: Seat belt stuck

Open small plastic access panel located between front and rear doors a few inches above floor. Disconnect the two wire connector (usually attached to car frame) and locate the male pin connector, usually 1 red and 1 blue wires. Run two long wires from a car battery negative post and positive post (battery on the car or separate.) Hold one wire against one pin of the connector and quickly touch the other wire against the remaining pin. This will cause the motor to turn in one direction. If motor turns in wrong direction simply reverse the wires until motor brings belt to desired position then quickly remove the wires. Reattach connectors to resume 'normal' operation after 'CAUSE' has been repaired.

Posted on Aug 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I release a stuck new seat belt retractor?


You are probably pulling belt at the wrong angle and it won't release. Pull with easy steady tension, trying a different angles and it should come free for you. If it doesn't, then take it back to SEAT or VW, they can show you in 1 minute how to free it. Since it's a mandatory safety device, there should be no charge unless it requires replacement.

Apr 04, 2015 | Seat Cars & Trucks

1 Answer

The rear drivers side passenger seat in my Mercedes 2004 ml350 is stuck down...how do get it to come back up. very little room to work


Not an easy task. You likely have one of 2 problems. If center seat belt is in the seat that is down, it may be locked. If so, you need to remove the seat back cover then the seat belt retractor. You can then position the seat belt retractor upright (how it sits when the seat is up) and pull the seat belt out making slack to raise the seat. This only happens if the either the stop on the seat belt is broken or the seat belt guide on the seat back is broken. If that's not the problem, you likely have a release cable that has come loose under the seat. If you look at the half that works, you can determine what you need to move on the locked seat and try to get to it with a long tin screwdriver or similar implement.

Mar 01, 2015 | 2004 Mercedes-Benz ML 350

1 Answer

How to replace 3rd row seat drivers side seat belt?


Please bear with me, a lot of people don't know that if this occurs that you must start the vehicle and relax and pull out the seat belt with a firm and steady action but not to pull too fast or no yanking. You must start the vehicle to reset the security system for the vehicles safety belts to release and go back to ready to use mode

May 01, 2014 | 2003 Toyota Sienna

1 Answer

I have a 2005 mercury montaineer. The drivers seat which is a power seat, will not go back all the way. It makes it half way and then nothing. Please help!!!


Most Ford products are designed so the seat belt latch by the center console moves with the seat. The bottom of the latch rides on the seat rail, and with time sometimes it builds up a little play on the rail. As the seat moves forward or back, the seat belt guide often tilts forward or back, just a bit, on the rail, and gets stuck. So you can move forward or back just a bit, but then it jams and you can hear the motor, but can go no further.

The long term fix is to remove the seat, disassemble the seat belt guide and rail, and usually replace some parts.

But the short term solution is often to simply hold on to the seat belt latch and rock it forward and away from the seat as you try to go forward or back. Or, sometimes it works best to rock it backwards and away from the seat as you try to move forward or back. It all depends on which way it is binding.

There's no guarantee that it won't jam again if you move it all the way back or forward, but once you find the right position to hold the seat latch in while moving the seat, you should be able to re-adjust it where you need it to be.

Aug 28, 2013 | Cars & Trucks

1 Answer

I have an 03 lincoln navigator the driver seat wont go forward or backward it can only go up and down, but every time touch the switch i hear a click, what can be my problem and what can be done to solve...


Most Ford products are designed so the seat belt latch by the center console moves with the seat. The bottom of the latch rides on the seat rail, and with time sometimes it builds up a little play on the rail. As the seat moves forward or back, the seat belt guide often tilts forward or back, just a bit, on the rail, and gets stuck. So you can move forward or back just a bit, but then it jams and you can hear the motor, but can go no further.

The long term fix is to remove the seat, disassemble the seat belt guide and rail, and usually replace some parts.

But the short term solution is often to simply hold on to the seat belt latch and rock it forward and away from the seat as you try to go forward or back. Or, sometimes it works best to rock it backwards and away from the seat as you try to move forward or back. It all depends on which way it is binding.

There's no guarantee that it won't jam again if you move it all the way back or forward, but once you find the right position to hold the seat latch in while moving the seat, you should be able to re-adjust it where you need it to be.

Aug 23, 2013 | Cars & Trucks

2 Answers

1994 olds 98 rear seat belt (behind driver seat) is stuck


If brute force doesn't unstick it remove the back seat and pull the cover off of the reel. The problem should be apparent. You can turn the reel with a large screwdriver if need be.
If the belt is damaged find another one at your local recycler, the side reel is behind a plastic panel that is easily removed, the assemblies are held in by big bolts.

Sep 13, 2009 | 1994 Oldsmobile Ninety Eight Regency

1 Answer

My seat belt light stays on in my BMW Z4. Is there a solution to this.


The contact in your seat belt buckle needs cleaned, (when you click the belt into the buckle the connection is not being completed keeping the dash light on.) Try inserting a thin flat blade screw driver with a lint free cloth dipped in rubbing alcohol into the buckle and slide to and fro gently. do this a few times moving cloth o a clean spot each time till no dirt shows.

Jul 11, 2009 | 2003 BMW Z4

1 Answer

Seat belt problem


okay hears the deal take the interior coner panel off on the side right behind the sea you will find the retracter take the cover off and loosen the spring till you can freely hold the belt then reajust the spring...take then tighten the spring down and let the belt go till the spool is just about full then mark the part of the belt were when i is spooled would be stoped at the corner panel then sew some kind of coth stop on it so that the spool doesnt get overwound and the sprong locks or the belt gets jammed i had to do that with one of my buddies trucks and yes it is a pain inthe ***

Feb 19, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
2001 Ford Taurus Logo

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...