Question about Cars & Trucks

1 Answer

Its a 2012 fieasta change the servo .marster cilnder and the peddel still goes to the floor

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Bleed the complete system starting with the rear passenger caliper if you don't have a bleed box get someone to help you and have them pump the brakes three to five times and hold it down then open the little 3/8 bleeder located on the inner side of the caliper the brake pedal will go to the floor but make sure they do not release the pedal until you close the bleeder back up then repeat until there is no air in the lines then move to the rear driver side repeat steps above then front passenger side then front driver side. hope this helps Jeff J&D services

Posted on May 15, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 394 Answers

SOURCE: soft break peddel

Sounds like you have a vacuum booster issue or a brake master cylinder going out. If you know of an independent mechanic the Vacuum Booster test is simple. It is recommended to replace both the booster and the master cylinder at the same time.

Posted on Feb 09, 2010

Testimonial: "thanks that what i was thinking "

  • 7353 Answers

SOURCE: i have no breaks on

Did you check the brake fluid level? if its low, you may have a broken brake line. look for a wet area under the van. Most likely you have rusted brake lines and need them all replaced. expensive.

Posted on Dec 14, 2010

  • 203 Answers

SOURCE: my brake peddel is spongee-soft, and goes to the

when you push pedal hard & pedal goes to floor does brake light come on?
assuming brake fluid leval is ok & didnt run empty have you checked for a leak?
pulling all wheels & inspecting brakes,cylinders, calipers,& lines for leaks.
does the pedal pump up & feel ok with engine running?if so there is air in the system
if it does'nt change the way the pedal feels & no leaks are found & brake linings are ok & adjusted
properly than your master cylinder is leaking internally & needs to be replaced

Posted on Jul 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 02 explorer canged od servo and intermed servo cap blew off ?


5R55W -2002 Ford Explorer - Servo Replacement Saga. - Ford ...

https://www.explorerforum.com/forums/showthread.php?t=380199

Oct 18, 2014 - 19 posts - ‎4 authors
I have a 2002 Ford Explorer XLT. ... My plan was to replace both Overdrive and Intermediate servo's with a new pair that was ... Lifted truck off the ground. ... With both snap rings removed, I removed the servo caps. .... Elite Explorer members canchange the forum "styles" to eliminate most ads, including the ...Missing: intermed

blown out servo cover - 5r55e - Ford Explorer and Ranger Forums ...

www.explorerforum.com/forums/showthread.php?t=346555

Feb 19, 2012 - 15 posts - ‎4 authors
blown out servo cover - 5r55e Explorer & Ranger Transmissions, Transfer ... 02-18-2012, 02:08 PM ... Got underneath and discovered that the OD servo cover had ...Once I get the cover back on I could just top off the fluid and hope for the ... EliteExplorer members can change the forum "styles" to eliminate ...Missing: intermed

Jan 18, 2016 | Cars & Trucks

1 Answer

Break pedal goes to floor but still has ablity to stop


Check that vacuum line to the servo or booster (as it is sometimes called) is attached with no holes in it if that looks good then its probably the servo. the servo is what your master cylinder bolts onto. this happened to mine, to replace simply unbolt master cyl. from serve the unbolt servo by reaching under dash just above brake pedal and pulling carpet down and remove the 2 or 3 nuts or bolts holding servo then pull servo from firewall and replace.

Feb 26, 2014 | 2005 Mercury Mariner Premier

1 Answer

My brake peddel is spongee-soft, and goes to the floor if i prees hard?


when you push pedal hard & pedal goes to floor does brake light come on?
assuming brake fluid leval is ok & didnt run empty have you checked for a leak?
pulling all wheels & inspecting brakes,cylinders, calipers,& lines for leaks.
does the pedal pump up & feel ok with engine running?if so there is air in the system
if it does'nt change the way the pedal feels & no leaks are found & brake linings are ok & adjusted
properly than your master cylinder is leaking internally & needs to be replaced

Jul 05, 2011 | 2001 Chevrolet Silverado

1 Answer

I have no breaks on my van peddel goes down to floor


Did you check the brake fluid level? if its low, you may have a broken brake line. look for a wet area under the van. Most likely you have rusted brake lines and need them all replaced. expensive.

Dec 14, 2010 | 1993 Ford Econoline

2 Answers

I have brake power when the car is off but brake pedal goes to the floor had to stop when the car is on


you could have air in your lines you may have to bleed the lines or set your break peddel.

Nov 15, 2010 | 2003 Ford Taurus

1 Answer

Foot peddel does not respone . it will start but if you push peddel down the motor pops back though air intake. change fuel filter and made shore getting gas to filter.


havent a clue sitting here i would really need my head under the bonnet to have a look then kick it and then repair it ,now it could be anything from low fuel pressure to a pipe come adrift on the inlet manifold ,like for the servo or the engine breather

Aug 12, 2010 | 1997 Chevrolet Astro

1 Answer

Soft break peddel


Sounds like you have a vacuum booster issue or a brake master cylinder going out. If you know of an independent mechanic the Vacuum Booster test is simple. It is recommended to replace both the booster and the master cylinder at the same time.

Feb 09, 2010 | 1995 Buick Riviera

1 Answer

Starts then dies willrun a bit with the peddel to


fuel pump if your lucky its just a dirty Fuel Filter.

Aug 19, 2009 | 1999 Pontiac Grand Prix

1 Answer

2002 hyundai accent my cluch peddel goes soft


check fluid level if low bleed out the system.If thats fine then you have slave cylinder Problem.Before Changing the cluch assembly check your master cylinder is pushing good pressure.

Jul 17, 2009 | 1998 Hyundai Tiburon

1 Answer

Trouble Bleeding Break Line


you need to hold in the metering valve.when you bleed the front brakes.long as the valve closed off you wont be able to bleed front brakes.better to get extra help.hard to bleed by your self .

Apr 20, 2009 | 1988 Oldsmobile Delta 88

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...