Question about 2003 Dodge Neon

2 Answers

Cant remove headlamp to replace bulbs on neon RT 02

I have removed the two scrwes on my chrysler neon 02 rt, the module is loose but will still not come out plz plz help

Posted by on

  • j_o_e_l_y Jun 23, 2009

    all screws are out and the headlamp is moving around but i am still unable to get it out ??????

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hi i have an rt and had the same problem i changed the pass side i removed the air filter box witch gave me easy entry to the bulb. regards sully

Posted on Jul 30, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Sometimes they need to have to have a little persuasion to get them out. Try prying on them gently with a screw driver. Make sure you do have all the screws out first.

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlights will not come on 02 s10


Have you checked fuses ? The Instrument panel fuse block , Fuse Block - I/P
LH of the I/P, near the door jamb switch - LF , fuse # 7 HDLPSW 10amp.
In the underhood fuse / relay box - Headlamp power relay , RT HDLP fuse 15amp LTHDLP fuse 15amp.
Battery positive voltage to the headlamp switch is supplied by the HDLP SW fuse in the IP fuse block. When the headlamp switch is in the HDLP position, the headlamp power relay coil is energized. A voltage signal is also sent to the body control module (BCM) signaling that the headlamp switch is activated. The headlamp power relay coil is grounded at G102. When the headlamp power relay is energized, the relay supplies battery voltage to the LT HDLP and RT HDLP fuses. Both low beam headlamps are grounded by the multifunction headlamp dimmer switch in the low beam position through the normally closed headlamp grounding relay in the body relay block to G200.
High Beams-Except ZR2 Battery positive voltage to the headlamp switch is supplied by the HDLP SW fuse in the IP fuse block. When the headlamp switch is in the HDLP position, the headlamp power relay coil is energized. A voltage signal is also sent to the body control module (BCM) signaling that the headlamp switch is activated. When the headlamp switch is in the AUTO or PARK position and the ambient light sensor detects darkness, the BCM produces a voltage signal that will also energize the headlamp power relay. The headlamp power relay coil is grounded at G102. When the headlamp power relay is energized, the relay supplies battery voltage to the LT HDLP and RT HDLP fuses. The RH high beam headlamp receives current directly from the RT HDLP fuse. When the headlamp switch is in the HDLP position, the BCM removes the ground path to the headlamp grounding and DRL relay coils. This allows current to flow to the LH high beam headlamp through the normally closed contacts of the DRL relay. Both high beam headlamps are grounded by the multifunction headlamp dimmer switch in the high beam position through the normally closed contacts in the headlamp grounding relay to G200. A ground signal is also sent to the BCM in order to confirm high beam operation.

In the i

Mar 01, 2015 | Cars & Trucks

1 Answer

How do I install a headlight assembly for a 2005 dodge neon


HEADLAMP MODULE REMOVAL
  1. Release hood latch and open hood.
  2. From behind bumper fascia, remove bolt holding outboard end of module to fender.
  3. Loosen bolts holding inboard end of module to radiator closure panel.
  4. Remove bolt holding grille to headlamp module.
  5. Remove bolts holding top of module to upper crossmember Headlamp Module
  6. Disengage wire connector from headlamp and parking lamp sockets.
  7. Separate headlamp module from vehicle.
INSTALLATION Reverse the preceding operation.

Feb 18, 2011 | 2005 Dodge Neon

1 Answer

Lowbeam head lights dont't work after changing bulbs


{: ) For the lowbeam headlamps, check these fuses at the underhood fuseblock:
LO HEADLAMP LT 10amp
LO HEADLAMP RT 10amp
HDM 15amp (main power for the HDM relay. Important)
Voltage is always present at the HDM fuse. When you switch on lowbeams, voltage should be present on the LT and RT fuses. Otherwise check the HDM relay or swap it with another known good and similar relay.
Check the two fuses again for votage:
If voltage is now present, proceed with wiring checks, checking for open wiring going to the bulbs.
If voltage is still not present on the two left and right fuses, but the HDM fuse and relay voltages are okay, you may be having a bad fuseblock.

Aug 07, 2010 | 2006 GMC Envoy

1 Answer

How do I get to the drivers side light bulb in a 2006 Chrysler Sebring Sedan? I have the replacement bulb and want to change it myself.


I will assume you are talking about the headlight?!

Removal
CAUTION: do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced life will result.

1) Disconnect and isolate negative battery cable.
2) Remove headlamp unit retaining screws. (bolts)
3) Remove headlamp unit to expose back of unit.
4) Disconnect wire connector from back of headlamp bulb.
5) Rotate retaining ring counterclockwise.
6) Remove retaining ring.
7) Pull headlamp bulb and remove from headlamp unit.

Installation

1) Install headlamp bulb to the headlamp unit.
2) Install headlamp bulb retaining ring.
3) Rotate retaining ring clockwise.
4) Connect wire connector to bulb.
5) Install headlamp unit.
6) Install headlamp retaining screws. (bolts)
7) Connect the battery negative cable.

More detailed info on how to get unit out.

Removal

1) Disconnect and isolate the battery negative cable.
2) Remove the two retaining screws.
3) Remove the upper fascia retainers by prying under the head of the fasteners with a flat bladed tool.
4) Remove headlamp unit from fender side first, then pull headlamp unit out.
5) Disconnect the wiring harness from the bulbs.
6) Remove the headlamp unit.

Installation

1) Connect wire harness to the bulbs.
2) Install headlamp unit.
3) Install the retaining screws.
4) Install upper fascia retainers.
5) Connect the battery negative cable.

I hope this will help you to get the light changed.

Jan 11, 2010 | 2006 Chrysler Sebring

1 Answer

How to change lowbeam headlight bulb on 02 chev trailblazer


  1. Open and support the hood.
  2. Remove the grille.
  3. Pull up on the retaining tabs in order to remove the headlamp assembly from the headlamp panel.
  4. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
  5. Disconnect the headlamp electrical connector from the headlamp assembly.
  6. Remove the side marker socket from the headlamp assembly.
  7. Remove the park/turn socket from the headlamp assembly.
  8. Remove the headlamp assembly from the headlamp panel.
  9. Remove the access cover from the rear of the headlamp.
  10. Disconnect the electrical connector from the socket.
  11. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  12. Disconnect the electrical connector from the socket.
  13. Remove the bulb and socket from the headlamp.
Replace the low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.


Oct 17, 2009 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Neon 2002 RT lack of power


1 Inspect Throttle Position Sensor Faulty or Incorrectly Connected Throttle Position Sensor.
2 Inspect Mass Air Flow Sensor Damaged, Loose, or Faulty Mass Air Flow Sensor or Circuit.
3 Inspect Choke Thermostat Stuck or Improperly Functioning Choke Thermostat.
4 Inspect Air Cleaner Tempature Sensor Damaged or Faulty Air Cleaner Tempature Sensor.
5 Inspect Fuel Filter Clogged or Dirty Fuel Filter.
6 Inspect PCV Valve Plugged or Damaged PCV Valve.
7 Inspect Carburetor Worn, Faulty or Damaged Carburetor.
8 Inspect Fuel Injector Dirty or Worn Fuel Injectors.
9 Inspect Hose (PCV)at Clogged or Collapsed PCV Hoses.
10 Inspect Fuel Pump Faulty Fuel Pump.
11 Inspect Fuel Pump Low Fuel Pressure.

Aug 14, 2009 | 2003 Dodge Neon

2 Answers

Headlight replacement


you doo not need to remove the bumper...the rt side is a bit tighter than the left side though..on the back of the headlamp are plastic screw retainers..they turn 1/4 to 1/2 turn to unlock the headlamp bulbs.( you could remove the battery to do this..it will certainly give you more room.) once you turn the lock grab the bulb and pull it straight back , unplug it and plug the new one in. be careful not to touch the new bulb glass with your fingers as this can get oil on the surface and create a "hot spot" which can lead to premature failure!

Oct 16, 2008 | 1992 Honda Accord

1 Answer

HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Jul 28, 2008 | 1994 Chrysler New Yorker

1 Answer

02 neon running rough


your coil my be going out not enough spark getting to it. take your coil off and get in checked at an auto part store or dealer.

Jul 02, 2008 | 2002 Dodge Neon

1 Answer

How to install 2003 dodge neon headlight assembly.


  1. Disconnect and isolate the battery negative cable.
  2. Remove screws attaching headlamp module to upper crossmember.
  3. Remove headlamp module from vehicle.
  4. Disconnect wire connectors from back of headlamp module.
  5. Remove headlamp module

Jul 02, 2008 | 2003 Dodge Neon

Not finding what you are looking for?
2003 Dodge Neon Logo

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...