Question about 1994 Jeep Wrangler

Open Question

1994 jeep YJ runs good at 55 then rough and stalls

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: Jeep wrangler Fuse box

i had the same problem. i drive a 95 so im not sure if it differs from were the fuse box is. look righ above you pedals to your far left. it should be right there. also if you instruments went out it will be a 15 fuse. its a blue fuse. next my panel went out cuz of the wires on my transmission. if yor looking at your jeep at the front. the wires will be on your left. make sure they are not burned or anything. it will be right on the side of your tranny. mind got burned by the exaust so they were shorting. check that is and see if that is what is it. for a temp fix just put some electrical tap around the wires and you should be set for a wile. good luck

Posted on Jun 30, 2008

teezay731
  • 1 Answer

SOURCE: rough idle stalls at low rpm's

check your transmission fluid,the motor will stall when fluid is low

Posted on Mar 24, 2009

  • 6982 Answers

SOURCE: My 89 Jeep YJ manual will not go in to reverse while running

Problem is likely either a worn shift fork or bad synchro (both inside the transmission) It's unlikely that you have a clutch problem otherwise the problem would be with first and reverse and shifting other gears would also be difficult.

Posted on Sep 01, 2009

  • 750 Answers

SOURCE: poor gas milage 1994 2.5 yj jeep

try changing spark plugs,servicing the fuel system, air filter,ignition system,oil and filter.try doing a compression test to see how the engine is doing

Posted on Oct 09, 2009

  • 6982 Answers

SOURCE: clutch pedal, starter, ignition... where is the

If you find the switch, you can temporarily jump across it, 'till you get a new one. When you go to buy it you are looking for a clutch switch.
Neutral switches are found on automatic trans vehicles. If you jump it out, be VERY careful to make sure you start in neutral with the clutch depressed as without the switch, it will start in any gear even with the clutch engaged.

Posted on Oct 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 jeep yj 4 cylinder the motor skips until you reach 55 mph


sounds like an engine misfire try to get a trouble code on it

Sep 27, 2015 | Jeep Cars & Trucks

1 Answer

Need the coolant eng temp control gauge wiring diagram for a 1994 2.5L jeep


the fsm 94 wrangler.
we have a free book, 93 YJ
see chapter, 8E-1 ? instrument...... (words only)
then chapter,wiring, (last is list)
see that? see pdf page, 55? index then on to instruments yj
page 44 real. PDF page 110. BINGO.
the it is.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

or alldata.com
or any real FSM from jeep.

3 choices. always.

Jan 24, 2015 | 1994 Jeep Wrangler

1 Answer

1994 Jeep YJ 4.0 5 speed manual - will run rough + speed odometer quits sometimes. new plugs,wires,distrubutor, cap,rotor,coil,02 sensor, crankshaft sensor. getting good fuel presure.


lots of guessing.

old car, but is Chrysler made, good that. 93+

ok, the car has a cel lamp. is it glowing running\'?

this is called misfire. is the engine stalling?

on all cars that old the first thing do is check compression.



the rules to end misfire are this (a full tuneup)

fails

1: compression all the fuel and spark in the world can not run dead cylinders. ever.

2: then spark, check that all spark plug tips are clean and the spark is strong. then check timing, if any thing here is wrong fix that next.

3: fueling this is complex and is always last. after spark.

I6 4.oL is nice motor owned 3 since 1988. zillion miles on them.

unlike 88s your\'s dont suck. mine had horrid french RENIX EFI......

nasty that..... is...



so you do the flash test on the CEL yet, see if you have DTCs stored.

if not why not? this be like first. its free, and is very helpful

if you have DTCs/ stored. DIag mode is activated with.



put the key in the ignition and turn the key to run (not start), then off, then run, then off, then run (that\'s 3 runs and 2 offs). Leave the key in the run position

count the blicks, best done just after misfiring.





fueling is complex.

6 injectors that can leak ,or clog.

the test is called a injector balance test. but is never done

before the 3 fuel pump pressure tests and the 2 regulator test

never. are those to be skipped and the tool is $20 lousy bucks.

if you get this far , we can do fueling all day. long.

but we also check all sensors for valid inputs.

as all ECU puke with bad inputs, all computers for that matter







saying good fuel pressure means zero with EFI, ZERO

only PSI matter.s not squirt tests. or other dribble tests.

those only proves pump is not 100% dead.

Oct 17, 2014 | 1994 Jeep Wrangler

1 Answer

Jeep YJ stalls while clutch is depressed


thrust bearings are bad and the flywheel is moving out of range of the crankshaft sensor, or the crankshaft sensor is sitting too close to the flywheel.

Mar 12, 2013 | 1998 Jeep Wrangler

1 Answer

Jeep Grand Cherokee 1997. Getting check engine light signal 12 14 43 55. Car symptoms are stalling rough idle.


Code 12 = Recently disconnected battery

Code 14 = Coolant sensor high resistance or shorted

Code 43 = Knock sensor or Electronic spark control circuit fault

Code 55 End read code.

Hope helps (remember rated this).

Jun 12, 2010 | 1997 Jeep Cherokee

1 Answer

1994 Jeep Wrangler YJ


order is 153624 gap is .35 remove one wire at a time and you won't have a problem putting the wires back on.

May 13, 2010 | 1994 Jeep Wrangler

2 Answers

94 yj will not crank over but I have a clicking sound, checked batt. and all leads, fuses look good, if I push start yj it will run great.. I installed a new starter and it will only click, will not crank.


It appears you have a poor battery cable ground connection. Remove the cable from the baterry ans lean the bat connection thoroughly. If this is a side post, put a ble in the terminal threads and see if the terminal is loose. If it is, The terminal is broken loose inside and the battery needs replacing. Good Luck, Ned

Nov 12, 2009 | 1994 Jeep Cherokee Country

1 Answer

Poor gas milage 1994 2.5 yj jeep


try changing spark plugs,servicing the fuel system, air filter,ignition system,oil and filter.try doing a compression test to see how the engine is doing

Oct 09, 2009 | 1994 Jeep Wrangler

1 Answer

2001 Nissan Maxima- runs rough, stalls when idle


Timing belt could have skipped a tooth.

Horrible vacuum leak could have started. Listen for suction noises when you raise the hood.

Someone could have poured sugar in your tank.

You could have put diesel in your tank instead of gas.

Could be a bad MAP sensor, TPS sensor, etc.

Need more details to be precise.

Feb 10, 2009 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Jeep Wrangler Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...