Question about 2002 Oldsmobile Silhouette

Open Question

How to fix horn not working 2002 Oldsmobile Silhouette?

Horn is not working when I press on it

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 833 Answers

SOURCE: Gas Gauge not working properly

First...how do you get 25 mpg...I get 21 or so!!!!  Additives will never work on this.  The price for the pump is $150-175 for an aftermarket unit.
I just did the tank job for the sender.  Get an aftermarket pump/sender.  DO NOT ORDER from RockAuto for this part...their listing is wrong.  They send the gasket...which comes with the replacement.  Replacing the unit is relatively easy:

  • Have less than 5 gals of gas in the tank.
  • Get the driver's side of the car in the air and support it.  
  • Remove plugs to the left of the tank on the bottom of the vehicle
  • Start car and allow gas pressure to subside...car will stall
  • Remove the fill pipe from the left rear of the tank..there is a valve on the fill pipe which will contain all but a few drops of gas
  • support the tank and remove the bolts that hold the tank straps and lower the tank.
  • lower the tank and remove the vent hose at the rear of the tank so you can swing it out
  • after swinging it out, prepare to remove the unit from the top of the tank retaining the connector snap ons for the new unit.  Clean the area around the pump to remove the possibility of contamination.  Tap the ring sharply counterclockwise to remove it from the tank.
  • Remove old and install new, pressing the unit into the tank...be sure to use that new gaaket they gave you.  Tap on ring, swing tank back, reconnect hoses, raise and bolt up.  Plug in.
  • Start the car after turning key and waiting for 15 seconds to start so pressure can build.
I did it in 3 hours.  If you have help for liffting and all that, probably 2..2 1/2

Posted on Nov 11, 2008

Ad
keeperoffire
  • 106 Answers

SOURCE: 2002 Oldsmobile Silhouette ABS Light is on and

The first thing i would check is all 4 abs sensors at the wheels.You can do this with a volt meter set on ac voltage and spin the wheel if it generates voltage at all on the meter its good.

Posted on Mar 06, 2009

  • 8 Answers

SOURCE: lower intake manifold gasket leaking 02 Olds Silhouette

This is basicly a very time consuming job rather than a physically hard one to complete. In order to replace the gasket you must remove the intake plenum,throttle body, and misc. vacuum hoses. The wiring harness connections must also be disconnected. Finally the intake manifold is exposed. The bolts holding the manifold to the block are removed exposing the leaking gasket. After removing the push rods and placing them in the correct order to be replaced the gasket and sealants can be removed. Finally replace everything in reverse order. Be sure to consult a GM manual for correct bolt torch specs. The correct specs for the manifold bolts usually come with the gasket. Make sure to change your oil a few times after this job in case any coolant entered the block. Also,change the thermostat and the oil seal on the distributor half shaft cap while you have everything off. Good Luck

Posted on May 12, 2009

  • 66 Answers

SOURCE: Where can I get a replacement remote for a 2002

try Ebay

Posted on Jun 29, 2009

  • 1757 Answers

SOURCE: i need to know the correct firing order for a 2002

For the 2002 Oldsmobile Silhouette:

For the 3.4L V6:

Firing Order:
1-2-3-4-5-6

Cylinders:
.......(back).......
|...1....3....5...|
______________
|...2....4....6...|
.......(front)

Ignition Coil Connections:
.|.5..2.|..|.3..6.|..|.4..1.|

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Posted on Apr 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 oldsmobile silhouette van,can lower passenger window but cannot raise it, works both ways from passenger controle


You most likely have a bad switch on the drivers side. Pretty easy replacement and fix. Not bad cost wise either.

Apr 07, 2016 | 2002 Oldsmobile Silhouette

1 Answer

Where is the horn in front?


check the fuse first. check under the front of the car .near the front bumber.

Dec 21, 2013 | 1993 Oldsmobile Silhouette

1 Answer

Horn not working 1992 olds silhouette


if the horn unit has electricity going to it when applaying the and its grounded good then you might check its router thats right under the steering wheel if its good the the Horn needs to be changed.

Aug 31, 2011 | 1992 Oldsmobile Silhouette

1 Answer

My horn stopped working on my 2001 oldsmobile silhouette. It made a funny noise before it went out. We changed the relay but that didn't do the trick. Any ideas?


The horn itself is dead , that funny noise was it's last breath. You can get a horn from an auto wrecker for just about nothing. It does not necesarilly have to be from the same vehicle , as long as it fits.

Feb 10, 2011 | 2001 Oldsmobile Silhouette

1 Answer

I need to know the correct firing order for a 2002 oldsmobile silhouette


For the 2002 Oldsmobile Silhouette:

For the 3.4L V6:

Firing Order:
1-2-3-4-5-6

Cylinders:
.......(back).......
|...1....3....5...|
______________
|...2....4....6...|
.......(front)

Ignition Coil Connections:
.|.5..2.|..|.3..6.|..|.4..1.|

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Apr 27, 2010 | 2002 Oldsmobile Silhouette

1 Answer

Horn won't honk on 1993 Olds Silhouette.


hi take the wires off the horn and using a set of jump leads from the battery conet the jump leads onto the horn and see if it works then, if not horn faulty, if works blown fuse or a broken wire regards

Feb 01, 2010 | 1993 Oldsmobile Silhouette

1 Answer

2002 Oldsmobile Silhouette ABS Light is on and


The first thing i would check is all 4 abs sensors at the wheels.You can do this with a volt meter set on ac voltage and spin the wheel if it generates voltage at all on the meter its good.

Mar 06, 2009 | 2002 Oldsmobile Silhouette

2 Answers

Horn doesn't work


Do you hear a clicking noise in the car when horn is repeatably pressed? If so the horn itself is burned out, if you want to verify the horn problem go to the horn location and with a 12 volt test light (avail at any auto parts store) have someone press and hold the horn on, then probe the horn wire terminals and see if the test light lights.

Jul 28, 2008 | 1995 Oldsmobile Silhouette

Not finding what you are looking for?
2002 Oldsmobile Silhouette Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...