Question about 1999 Ford Taurus

1 Answer

Belt inst ford taurs

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 224 Answers

For the 3.0L Vulcan, you have a tensioner that is located just below the power steering pully. Use a 15mm wrench or the 15mm shallow well socket that comes in a Serpentine Belt tool to push the tensioner toward the rear of the engine compartment. Take the old belt off and route the new belt. The belt begins at the crankshaft pully, goes under and around the a/c compressor, up around the power steering pump, around (with the flat edge) the idler pully, around the alternator, the flat edge then sits against the tensioner and back around to the water pump pully. You should have a belt routing diagram on the underside of the hood just above the serpentine pully assembly.

Posted on Jun 23, 2009

  • Joseph Weisenberger
    Joseph Weisenberger Jun 25, 2009

    When installing the new belt, you'll need to use a screwdriver to pull it up and over the alternator pulley. This really is the easiest way to install.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size belt for a 2004 ford taurs


An auto parts supplier can tell you.

Mar 02, 2017 | Ford Cars & Trucks

1 Answer

Repair 1997 ford taures purge control valve


Well there is no one thing that causes this fault code but here are what can trigger the fault in the fuel vapor control system.
P0443 FORD - EVAP Purge Control Circuit
Possible causes- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection
- Faulty Evaporative Emission (EVAP) Purge Solenoid Control

Apr 17, 2012 | 1997 Ford Taurus

2 Answers

94 ford taures keeps throwing drive belt


Your either not routing it right or a pulley is bent/bearings shot. Check to make sure its routed right, while the belts off check all the pulleys.

Jan 19, 2011 | 1994 Ford Taurus

1 Answer

How do i put a serpentine belt on a 2004 ford taurus?


look under hood for belt routing diagram, then obtain belt and belt tensioner tool from advance auto and it will be easy. 10 min job. If no diagram draw one yourself then use that for reference.

May 20, 2010 | 2004 Ford Taurus

1 Answer

Where to find Belt routing 94 Tauras 3.8


Should be on the back of the pack that the new belt comes in.

Mar 29, 2010 | 1994 Ford Taurus

1 Answer

Need a cerpenteen belt diagram for a 2001 ford taurs se


give this website a try Drive belt diagrams www.webcrawler.com wish you the best of luck Michigan Man.

Feb 23, 2010 | 2001 Ford Taurus

2 Answers

Ford Taurs will turn over but not start


check for spark, check timing, check for fuel pressure

Sep 12, 2009 | 1995 Ford Taurus

1 Answer

How to exchange rear tail light assembly on 2003 taures


open the trunk remove the scuff plate that is located on the back part of the trunk closest to you. then pull the carpet back on the side that you are trying to get to and remove the three or four nuts holding the light assembley in. pull the assembley away from the body then disconnect the bulbs from the assembley. thay should just turn and come out socket and all.

Jan 12, 2009 | 2003 Ford Taurus

Not finding what you are looking for?
1999 Ford Taurus Logo

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...