Question about 1999 Honda CR-V

Open Question

How to replace coil - 1999 Honda CR-V

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 1986 chevy celebrity tec4 an have no fire from coil ive replaced coil checked fuses an have power going to coil still no fire


ignition will trigger if signal from crank sensor, with hei spark plug tester ,read to coil wire and spark plugs wire if spark , depends wich engine
if c3i coil and module the module could be the problems you can check it before replace
hope it helps

Mar 29, 2014 | 1986 Chevrolet Celebrity

1 Answer

Right coil keeps burning out


For coils to burn it indicates either the incorrect voltage coil in use or a dead short through the primary windings or failed resistor in the circuit.
Coils come in either straight 12 volts or 12 volts start but run on 7 volts through a resistor or resistor wire . If that resistor is shorted out the 12 v on the 7 volt windings will burn out the coil . Coils are connected in parallel and never in series as that increases the amp loading on the coil windings . Check the ignition module for the second coil as it may be shorting out internally.

Feb 15, 2014 | 1995 Ford Crown Victoria

1 Answer

How to replace ignition coils


Its a procedure,its not that difficult to replace ignition coils.

Click here


--------
For more help,click the link below:---
How to test and replace Ignition Coil Pack on Audi A4 Car models? http://repairhelpcenter.blogspot.com/2011/11/how-to-test-and-replace-ignition-coil_19.html

--------

How to Replace a C.O.P. Type Ignition Coil?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-cop-type-ignition-coil.html

--------------

How to Replace an Ignition Coil

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-ignition-coil.html

------------------

How to Replace an Ignition Control Unit

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-ignition-control-unit.html

-----------

How to Replace an Ignition Wire Set

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-ignition-wire-set.html

----------

------------
How to Test Ignition Coil?

http://schematicsdiagram.blogspot.com/2011/12/how-to-test-ignition-coil.html

------------
Engine not getting spark from distributor?

http://schematicsdiagram.blogspot.com/2011/12/engine-not-getting-spark-from.html

--------
Cost to replace ignition coil?

http://technoanswers.blogspot.com/2012/01/cost-to-replace-ignition-coil.html
-------- Ignition locked up on Mercury Villager?

http://technoanswers.blogspot.in/2012/01/ignition-locked-up-on-mercury-villager.html

----------
How to replace ignition coil for Toyota rav4?


http://technoanswers.blogspot.in/2012/02/how-to-replace-ignition-coil-for-toyota.html

----------

These details will help.

Thanks.

Oct 16, 2012 | 1998 Lincoln Town Car

1 Answer

My 1198 bmw 318i compact is only sparking on 1&3 cylinder


Improve the FixYa experience for everyone by voting. I want you to let me know if the solution(s) suggested were of any value. Constructive criticism is welcomed.

Hi,

I'm Ben and -- hopefully -- I can provide some meaningful assistance.

I recommend a diagnostic scan to confirm my diagnosis of a malfunctioning coil(s).

How to Test and Replace Ignition Coil on BMW 3 Series


The following procedures apply for BMW 3 series (6-cylinders engine) 1992 - 1998 model years. To Test and Replace the Ignition Coil, do the following:
  1. Remove plastic engine covers from top of engine by prying off nut covers and removing cover mounting nuts.
  2. Disconnect harness connector from coil. Connect multimeter between terminal 15 (+) in connector and ground. (use a digital multimeter for the following test). See Fig.1. below BMW 3 series coil harness
  3. Turn ignition on and check for battery voltage. If battery voltage is not present, check wire between terminal 15 and ignition switch. The wiring to terminal 15 (+) of the coil (via the ignition switch) is not fuse protected. Use care when testing this circuit.
  4. Turn ignition off.
  5. Use a multimeter to test coil primary resistance at coil terminals. (primary coil terminals: 1 (-) and 15 (+), primary coil resistance: 0.4-0 .8 ohms; secondary coil terminal and resistance: NA).
  6. Remove coil and inspect coil housing for hairline cracks or leaking casting material . A leaky ignition coil may indicate a faulty engine control module (ECM). Check ECM before installing a new coil.
  7. When replacing ignition coils, ensure that the replacement coil(s) are from the same manufacturer containing the same part code numbers. If individual coils with the correct specifications are not available, all coils should be replaced.
5_30_2012_5_17_32_pm.png

May 30, 2012 | BMW 318 Cars & Trucks

2 Answers

05 Ford Escape, coils #3 & #4 not firing. We've replaced the battery, spark plugs, alternator, coil packs, & pcm. Had pcm reflashed. Garage said it had to be coil packs, but just replaced coil packs 3


Check engine light on ? Code's ? What engine ? 2.3 l 4cylinder or 3.ol v-6 This vehicle has coil on plug ignition system , not coil packs ! a coil per cylinder . If new coils an still has no spark , has no B+ voltage to the coil or the PCM isn't controlling them . Without testing i'd only be guessing as to the problem .If the repair shop you had it to can only say it had to be the coils , I'd find another shop to take it to !
Autolite Coil on Plug Ignition troubleshooting

Jun 22, 2017 | Cars & Trucks

2 Answers

How do you change coil packs on a 2002 Mazada tribute v6


I believe the Mazda V6 is the same as my 2002 Escape and uses individual coil-over-plugs or COPs. Each spark plug has it's own coil.
I've had an engine light twice, and needed to replace coils. I finally replaced them all. They are available at Ford, car parts stores like AutoZone, or I bought my full set of 6 coils on Ebay.
Autozone coils, for example are about $70/coil.
One of the difficulties with replaceing the coils, is that the 3 coils on the "back" of the engine are covered by the intake manifold. The manifold needs to be removed to get to them. You'll need the manifold gasket set, which costs less than $15.
The coils themselves are easy to replace. Unplug the 2 wire connector, unscrew one bolt (using 8mm socket?), and pull the coil up and off the plug.
I recommend replacing all the coils, and also replace the plugs while you're in there. Use OEM plugs; probably Motorcraft. (If the original plugs lasted 100,000+ miles, why would you experiment with something else?)
Here's a picture of one coil:

zeevert_81.jpg

Aug 29, 2011 | 2002 Mazda Tribute

2 Answers

How do I replace a coil for 2005 lincoln ls


You have 8 coil pack's, to remove undo coil harness then remove small 8 mm bolt slide coil pack out and replace with new one, if replace all do same with all, you will have to work it around fuel rail, but I have never heard of all coil pack's going bad.

Dec 30, 2009 | 2005 Lincoln LS

1 Answer

1988 audi 80 4cyl. no spark from coil,new coil fitted,coil lead


hi i have a coupe 1994 have same prob told by audi to replace the distributor as was common failt on audi's i have replaced new leads ,coil ,dissy cap, and arm ,still the same awaiting on distributor to see if this works hope this helps

Apr 27, 2009 | 1988 Audi 80

3 Answers

One coil won't fire


check the signal voltage going to afected coil harness, should be geting 12v. if its 0, the you may have a broken wire or pin on jack for that coil assembly

Apr 04, 2009 | 1995 Mitsubishi Montero

Not finding what you are looking for?
1999 Honda CR-V Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...