Question about Cars & Trucks

Open Question

Ryobi s430 timing belt keeps jumping off , is their a tenshener or do I change the belt?

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 383 Answers

SOURCE: broken timing belt

beeni3: I hate to be the one to give you the bad news. BMW's had interference fit motors. this meant that when a timing belt failed or the the engine was assembled out of time it would bend valves. With the car being that old, you may be able to buy a used engine for under a $1,000. Repairing yours will far exceed that.
IF you decide to go that route: make sure you replace the timing belt, cam and crank seals and water pump before you install the engine.
Good Luck.

Posted on May 10, 2009

emissionwiz
  • 75822 Answers

SOURCE: valve timing for ryobi s430

You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..

Posted on Sep 04, 2012

SOURCE: The belt keeps jumping. Is their a tenshener or do

May be you have purchased an oversize belt, loose may cause jumping, see if there is any adjustable to tighten the belt is available besides the pulley, plus to check if pullye's alignment at two ends are in order. if these not work, then you have to replace the belt with proper size .

Posted on May 15, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The belt keeps jumping. Is their a tenshener or do I change the belt?


May be you have purchased an oversize belt, loose may cause jumping, see if there is any adjustable to tighten the belt is available besides the pulley, plus to check if pullye's alignment at two ends are in order. if these not work, then you have to replace the belt with proper size .

May 15, 2014 | Cars & Trucks

1 Answer

Valve timing for ryobi s430


You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..

Sep 03, 2012 | Cars & Trucks

1 Answer

Mercedes S430 trunk won't open


you have to stick the key in the trunk and turn it to the lefy while hittin the unlock button on the key pad 35 times has to be 35 and it will unlock. my battery died and it locked the trunk as u know i coudn't jump it cause the battary is in the trunk haha but yeah 35 times while hitting the key. mercedes wont tell u but my buddy works for inskip and filled me in your o so welcome from one s430 owner to another

Jul 15, 2012 | 2000 Mercedes-Benz S-Class

1 Answer

Ryobi s430 replace timing belt


the ryobi s430 has a hole in the timing wheel with ,perhaps a red mark on it or next to it like mine.lining that up with the piece at the bottom that goes straight down puts the cam lobes right at 180 degrees away from the rockers and readies the valvetrain for the compression stroke.if you remove the valve cover,which by the way has a really tough reusable gasket,youll see the cam and rocker arms.you want the lobes of the cams to be as fara away from operating the rocker arms as possible.next, you ll find top dead center to be not quite lined up, with respect to magneto edges and flywheel magnets.using a tiny screwdriver, you can put the tip in the spark plug hole not quite an inch and rotate the flywheel SLOWLY.being careful not to somehow allow the screwdriver to become pinched between the piston and cylinder(that spark plug hole is at a funky angle)at some point,youll fee fell the piston approach top dead center.youll notice there are a few degrees that the flywheel will turn before the screwdriver will fall back down,indicating travel has begun toward bdc(bottomdead center).you want the crank asembly to be set in the center point between when the screwdriver stops rising out of the spark plug hole to the point it just starts to fall back in.that should be close enough.my problem now is getting the timing belt OFF.mine is bad and I've torn down all the way past the flywheel.at this point,i can see the timing belt,but now there's this pressed bearing in the way that ive yet to figure out how to remove.viva la ryobi

Apr 12, 2012 | Cars & Trucks

1 Answer

I need a serpantine belt diagram for a 2000 mercedes benz s430


I need to see a diagram for putting the serpentine belt back on for a 2000 S430 Mercedes

Feb 22, 2011 | 2000 Mercedes-Benz S-Class

2 Answers

Will car still start if timing belt jump and if it do how will it run


99% of the time your car wont start if timing belt has jumped or broke you will still have spark but wont start

Jan 17, 2011 | Acura Integra Cars & Trucks

1 Answer

2001 Mercedes-Benz S430 serpentine belt diagram


Check the underside of your hood for a belt diagram. If it's not there, call your dealer with your VIN number to get the correct diagram.

Sep 20, 2009 | Mercedes-Benz 400-Class Cars & Trucks

1 Answer

Car wont start possible jump timing


car wont start could be many things.your timing belt change is due at 60000 miles.if you at a 100000 miles and not change it.you timing belt have a tensioner that keep it tight. .when it wears it loses tension and cause timing belt to slip time.i would check fuel system and ignition system for spark first before having.timing belt change. its going to cost you.

Jul 15, 2009 | 2001 Hyundai XG300

1 Answer

Broken timing belt


beeni3: I hate to be the one to give you the bad news. BMW's had interference fit motors. this meant that when a timing belt failed or the the engine was assembled out of time it would bend valves. With the car being that old, you may be able to buy a used engine for under a $1,000. Repairing yours will far exceed that.
IF you decide to go that route: make sure you replace the timing belt, cam and crank seals and water pump before you install the engine.
Good Luck.

May 10, 2009 | BMW 325 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...