Question about 2007 Saturn Outlook

Open Question

Location of bank 2 knock sensor on a 3.6l saturn outlook

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

redlinetech0
  • 33 Answers

SOURCE: how to replace a 1999 saturn knock sensor?

it is located on the back side of the engine below the intake manifold. hope this helps:929510b.gif

Posted on May 23, 2009

cooper0365
  • 347 Answers

SOURCE: bank 2 sensor 1 o2 sensor

should be right behind the cat converter

Posted on Oct 03, 2009

kapishtech
  • 2272 Answers

SOURCE: Location of knock sensor on

A knock sensor is threaded into the engine block and is supposed to sense when the engine starts to ping or spark knock and reduces the ignition timing accordingly.The knock sensor is located on the side of the engine.

  • Turn the ignition OFF.
  • Raise the vehicle.
  • Disconnect the knock sensor harness connector.
  • Remove the knock sensor attachment bolt and the knock sensor.

  • Important: The larger metal contact area of the knock sensor MUST be toward the engine block. DTC P0327 may result if the sensor is installed backwards.

  • Install the knock sensor and attachment bolt with the larger metal contact area toward the engine block.

  • Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

  • Posted on Sep 22, 2010

    • 396 Answers

    SOURCE: I have a 2000 saturn

    replace the oxygen sensor closest to the cadalatic converter, that is the bank 2 sensor, that should fix your problem

    Posted on Dec 03, 2010

    dttech
    • 4803 Answers

    SOURCE: Where is oxygen sensor bank 1 sensor 2 located on a 2001 Saturn lw300?

    There is an article (tip) about this very subject. To read the article, click the following link:

    Which Oxygen Sensor Is It?

    Posted on May 25, 2012

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    What is the average cost to fix a knock sensor on a 2007 Saturn Outlook and how difficult is it to fix


    You need to have it diagnosed first , may not even be a bad knock sensor . Would hate to see you spend money needlessly ! An your vehicle has two knock sensors bank 1 an bank 2 .What DTC ?

    Nov 12, 2016 | Saturn Cars & Trucks

    1 Answer

    Knock sensor for 2007 Saturn outlook. I can't pass emissions test!


    Check engine light on ? What code ? There are many different (DTC'S) - diagnostic trouble codes that can set for knock sensors ! There all don't mean that you replace the sensor .
    DTC P0324: Knock Sensor (KS) Module Performance
    DTC P0325: Knock Sensor (KS) Circuit Bank 1
    DTC P0326: Knock Sensor (KS) Performance
    DTC P0327: Knock Sensor (KS) Circuit Low Bank 1
    DTC P0328: Knock Sensor (KS) Circuit High Bank 1
    DTC P0330: Knock Sensor (KS) Circuit Bank 2
    DTC P0332: Knock Sensor (KS) Circuit Low Bank 2
    DTC P0333: Knock Sensor (KS) Circuit High Bank 2

    The knock sensor (KS) system enables the control module to control the ignition timing for the best possible performance while protecting the engine from potentially damaging levels of detonation. The sensors are located below each cylinder head on the engine block. The KS produces an AC voltage signal that varies depending on the vibration level during engine operation. The control module adjusts the spark timing based on the amplitude and the frequency of the KS signal. The control module receives the KS signal through 2 isolated signal circuits. The control module learns a minimum KS noise level at idle and uses calibrated values for the rest of the RPM range. The control module should monitor a normal KS signal within the noise channel.
    Knock Sensor Replacement - Bank 1
    Remove the exhaust manifold lower heat shield. Refer to Exhaust Manifold Lower Heat Shield Replacement.
    Disconnect the engine wiring harness electrical connector (1) from the bank 1 knock sensor (2).
    Loosen the knock sensor bolt and remove the knock sensor.
    Knock Sensor Replacement - Bank 2
    Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
    Remove the engine oil filter. Refer to Engine Oil and Oil Filter Replacement .
    Lower the vehicle.
    Disconnect the engine wiring harness electrical connector (2) from the bank 2 knock sensor (3).
    Loosen the knock sensor bolt and remove the knock sensor.

    Nov 12, 2016 | Saturn Cars & Trucks

    2 Answers

    Is the bank 2 sensor 1 oxygen sensor on a 2010 Saturn outlook on the upstream or down stream side?


    The upstream on bank 2, which is the opposite of bank 1. Bank 1 is the side with the number 1 cylinder. Downstream oxygen sensors (after the cat converter) are always sensor 2, as in Bank 2, sensor 2.

    Mar 19, 2015 | Saturn Cars & Trucks

    1 Answer

    Where is the knock sensor located


    This vehical has two knock sensors bank 1 and bank 2 ! bank 2 sensor screws into the side of the engine block closest to the firewall. and it is above the crank sensor. Knock Sensor (KS) Bank 1 sensor is on front side of engine block right of the oil filter and on the other side of knock sensor is the oil pressure sending unit.

    Dec 26, 2014 | 2005 Saturn Relay

    1 Answer

    I am workimg on my 2000 nissan quest. it cranks and turns over but will not start. it is throwing codes P0340 twice and P0325. we replaced the distributor cap and rotor and still nothing. probably goi


    P0325 Knock Sensor 1 Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
    P0326 Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
    P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
    P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
    P0329 Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
    P0330 Knock Sensor 2 Circuit (Bank 2) -Circuit Malfunction
    P0331 Knock Sensor 2 Circuit Range/Performance (Bank 2)
    P0332 Knock Sensor 2 Circuit Low Input (Bank 2)
    P0333 Knock Sensor 2 Circuit High Input (Bank 2)
    P0334 Knock Sensor 2 Circuit Input Intermittent (Bank 2)
    P0335 Crankshaft Position Sensor -Circuit Malfunction
    P0336 Crankshaft Position Sensor -Range/Performance
    P0337 Crankshaft Position Sensor -Low Input
    P0338 Crankshaft Position Sensor -High Input
    P0339 Crankshaft Position Sensor -Intermittent
    P0340 Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
    sorry would a play with this to know for sure ,check the wiring plugs onto the sensors to make sure their not full of oil or corroded

    Aug 07, 2014 | 2000 Nissan Quest

    1 Answer

    Circuit bank 2


    Knock sensors are on the side of the engine block under the intake manifold. Bank 2 would be the sensor closest to the transmission above the starter as I recall.

    May 24, 2014 | 1998 Volvo S70

    1 Answer

    Where is knock msensor bank 2 on 04 2500 series 6.0 located


    They are Located UNDER Intake Manifold !! #1 bank in Front #2 Back.

    1. Remove the intake manifold.
    2. Gently pry up the rubber covers.
    3. Disconnect the knock sensor electrical connectors.
      1. Remove the knock sensors.
      INSTALLATION PROCEDURE

      NOTE: Refer to Fastener Notice in Service PrecautionsInstall the knock sensors. Tighten Tighten the sensor to 20 N.m (15 lb ft)
      1. Connect the knock sensor electrical connectors.
      2. Push down on the rubber covers.
      3. Install the intake manifold.

    Oct 08, 2009 | 2003 GMC Sierra

    4 Answers

    Knock Sensor


    Knock Sensors are located below the intake manifold or intake plenum and mounted to the block. They are circular and have a bolt at the center. On V6s,8s etc. and flat styled motors, they will have two knock sensors (bank 1 and 2). Bank 1 or 2 relate to V6s/8s/10s etc., or flat styled motors which have two separate heads and exhaust manifolds. Each manifold is a bank, so if there are two manifolds there are two banks. Hopefully this helps

    Sep 07, 2009 | 2002 Chevrolet Silverado 2500HD

    1 Answer

    I own a 2003 Chevrolet Express 3500 cargo van. The check engine light came on and the local hardware store, break out box indicates that the knock sensor circuit is the problem, bank 2. Which side of the...


    OK, bank2 is the side where the #2 piston is on. Usually its the pasanger side. To be sure open the hood and see which cylinder head is more forward than the other. the cylinder head set back is the bank 2 side. The knock sensor is located on the bank side of the block. You dont need a special tool. only a wrench. Make sure you clear all codes after installation of sensor.

    Jul 23, 2009 | Chevrolet Express Cars & Trucks

    Not finding what you are looking for?
    2007 Saturn Outlook Logo

    Related Topics:

    444 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Saturn Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8140 Answers

    Are you a Saturn Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...