Question about 2000 Acura TL
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Look for the end of the wire retainer clip. Unhook it and lift it up. Remember not to touch the bulb. But if you do, just clean it with a bit of alcohol.
btw - Here's a bit of info from a previous post of mine...
The low beams consist of three parts. The bulb, inverter/ballast and the ignitor. The bulbs usually start to loose their color long before they burn out. The inverters/ballasts either go out after a while or take a while to start up.
Before you spend money on a new bulb, try swapping it with the one on the other side. You'll need a security torx screwdriver to get the covers off of the back of the lights. Don't touch the glass bulbs. If you do, just clean them with a bit of alcohol.
If the problem stays on that side, try swapping the ignitors. They're mounted inside the black covers.
If the problem is still on that side you've got a bad inverter. They're mounted on the bottom of the headlight assembly. You'll need to remove the front bumper and remove the headlight assembly to get to it. (I recommend you take pictures as you remove things so can put them back together correctly.)
Posted on Jan 05, 2009
This starter can be changed without disassembling the top of the engine on the 2.5 with automatic transmission. You will need a 10mm, 14 mm, 17mm, and a 9mm wrench. First with any electrical repair disconnect the battery at the negative terminal. The starter is on the driver's side close to the firewall below the intake manifold. Remove the transmission dip stick so you don't ruin it, then look and study the starter itself. You will notice the starter drive housing with a top and bottom bolt. The top bolt is a 14mm and the bottom a 17mm, loosen both a half turn. Remove the top 14mm bolt first, then the bottom 17mm, this will allow you to pull the starter out of the bell housing. With some angling and no brackets holding the back of the starter you should be able to pull it out enough to disconnect the positive wire and 9mm nut from the soleniod. Disconnect the starter ignition small wire by pulling it off it's connector. Now just pull it out of the engine and fender void and you've got it, saving about a hundred and fifty dollars of labor. Take it to the parts house and match it up with a well made remanufactured or new starter. Reverse the proceedure, hook up the battery.
Posted on Mar 19, 2009
I have seen some problems with these sensors going bad when hot replace the sensor and the harness. before you condemm the computer.
Posted on Apr 04, 2009
SOURCE: firing order
Hello bailsdenied: THe fireing order for a Acura NSX 3.2L DOHC (vtec) engine is 1-4-2-5-3-6. If this is the correct model of car then it is right. If this is not the right car then ask and I will send the correct one. Please rate the answer you recieve as this lets us nkow you were provided the correct answer to your question. Thank you for using FixYa. Roger
Posted on Apr 25, 2009
If you can locate the temperature switch, looks like a large bolt head with 2 wires on it, bridge the wires on it, and this should make the fan work. If the fan works then this switch is faulty. If the fan doesn't then it could be the fuse, or a broken wire.
The fan switch is either on the radiator or on the thermostat housing.
If you can get to it easy, short across with a screwdriver.
Posted on Apr 27, 2009
Tips for a great answer:
Aug 05, 2017 | Acura Cars & Trucks
Feb 08, 2015 | 2000 Acura TL
Dec 08, 2013 | Cars & Trucks
Oct 17, 2012 | 2000 Acura TL
Feb 21, 2011 | 2004 Acura TL
Hello and Welcome to FixYa.com
Special Tools Required
02 sensor wrench, Snap-on YA8875. SP Tools 93750, or
1. Disconnect the primary 14025 4P connector (A), then
remove the primary H025 (B).
2. Install the primary H025 in the reverse order of removal.
Thank you for using FixYa.com
Regards, Lee Davidian
Your FixYa Expert
Jan 15, 2011 | 1999 Acura TL
Nov 16, 2010 | 2006 Acura TL
Oct 06, 2010 | 1998 Acura TL
Jun 10, 2010 | 2000 Acura TL
76 people viewed this question
Usually answered in minutes!