Question about 2005 Daewoo Lacetti 1.4

Open Question

How do i get my holden viva to run after replacing the key, ignition and barrell,i lost the key to my viva 2005 i have replaced the ignition barrel key and ecu wich i got off another viva 2008 it wont

Why won't my holden viva 2005 sedan start I replaced the key ignition barell and ecu due to me losing my key. Now engine light is on. Its wanting to start, and has for only a couple of seconds tho. What could be the problem please help.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: 2000 daewoo lanos

Maybe head gasket.

Posted on Jun 17, 2008

Ad
  • 31 Answers

SOURCE: i have daewoo leganza, and

you can install any engine as long as you have a good mechanic willing to take on the task! this will be very expensive and wont be worth the value of the car

Posted on Jul 22, 2008

  • 15 Answers

SOURCE: no spark

Check all your fuses. If there is no apparent problem, try running a direct wire from the pos (+) or red post on the battery to the positive post on your coil, then with this directly connected turn your key and see if it starts. If it does start you have a problem with the wiring from tour ignition to the fuse box or from fuse box to coil. If it still doesnt start you may need to check your spark plugs and then compression. If there is spark there but still wont run it could, and is more likely a fuel problem. Id suggest cleaning the carburettor, changing the fuel filter and blowing some air down the fuel line fron the engine end to the fuel tank, as there could be something blocking the end of the tube in the fuel tank. A good way to check if it is a fuel problem is spray a heap of ether spray/engine start into the carburettor then turn your key. If it starts then dies again, you only have a fuel problem. Working out which is the problem will make it easier to fix and save you a heap of money. Good luck and hope it helps. Let me know which way makes it start, with a wire to the coil, or with the enigine start into the carby and ill giude you further if you want.

Posted on Dec 31, 2008

  • 248 Answers

SOURCE: won,t start no ignition spark

Check all fuses and then fuel pressure, if all is good.
Then I would check to see if the tech moves when u try to start the engine.
If it does, then recheck crank sensor, might be defective.

Anthony

Posted on Jan 19, 2009

  • 1596 Answers

SOURCE: I need to remove the ignition barrel to replace it



IGNITION LOCK CYLINDER AND SWITCH

Removal Procedure

  1. Disconnect the negative battery cable
  2. Remove the lower steering column cover panel by removing the screws.
  3. Disconnect the electrical connector for the immobilizer detection coil, if equipped.
  4. With the key in the ignition turned to the position designated ACC, remove the lock cylinder by pressing down the detent spring with a 2.5 mm alien wrench or other suitable tool, and pulling the lock cylinder out of the switch cylinder housing. 5. Install the lower steering column cover panel with the screws. Tighten the lower steering column cover panel screws to 3 Nm (27 inch lbs.).
  5. Connect the negative battery cable

Posted on Jul 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Commodore. Why doesn't it start?


Did u get the key with the barrel...... If not the key may have to be coded to the barrel.... I.e immobiliser is not letting the car start... Try leaving the key in the ignition with the lights displayed on dash for two hours then try and start it.... See how you go

Feb 22, 2016 | Holden VT Cars & Trucks

1 Answer

How to remove ignition barrel from Holden Astra Sedan


Just replace the key faub. or try disconnecting the neg battery cable for about 5 min and then re connect it and it may reboot the system

Jan 01, 2014 | Cars & Trucks

1 Answer

I have a vt commadore can I take out the ignition barrell without a key.


yes but it means removing the exterior part also by undoing the anti tampering bolt on the clamp that holds the whole barrel to the steering column and replacing the assembly

Sep 15, 2013 | 1998 Holden VT Commodore

1 Answer

How to replace ignition tumbler on 2000 ml320 mercedes benz?


i would assume that there is a hardened steel sleeve "VERY HARD" that surrounds the barrel the same as the W140 model. the repair shop will have trouble cutting this off , like the novices at diesel motors in perth western australia. and will probably want to charge you around $3,000 AUD to replace the key and barrel. which collapsed in my case. jamming the key in the ignition. not bad for a vehicle that had cost $219,000 AUD , and had covered 220,000 km, when there countless thousands of 40 year old toyotas and holdens running around with the original ignition barrels. anyway , digressing , the switch that sits behind the actual barrel lock will no doubt fail not long after u change the barrel also. because i would say that the junk they manufacture for these over rated piles of trash (still riding on the reputation of their 1970's products, is about the same quality level as cheap rubbish componentry used in the W140 . "google search for W140 wiring harness there s a blog with a list of owners in the US with failed wiring insulation causing the copper wires to short out and in many cases cause engine fires. manufactured by Bosch to MB specification to be biodegradable, what a totally brilliant place to start , crucial electronic components, with severely limited life from the start.! , the ignition switch doesn't need to be cut out of the steel dash frame like in earlier models, and is not particularly hard to remove however the stealer will still try to slug u around a grand and tell u its a HUGE job. a friend of mine had my ignition barrel and switch out in 20 minutes after the switch behind the barrel failed after the dealer installed a new key and barrel and charged me 6 hours or so at $120/ hour.

Sep 13, 2013 | Cars & Trucks

1 Answer

Remove ignition barrel in vt commodore


you need to have the key in the ignition take the shrouds off there is a small hole underneath the barrell you have to push something small into the hole then pull out the barrell

Apr 09, 2013 | 1998 Holden VT Commodore

2 Answers

How do i take out my ignition barrel 98 vt


to remove you ignition barrel is a simple process you need to remover the steering column covers from around the ignition switch.
there is a small hole located in the ignition barrel you will need to gentle push and hold an Allen key in the hole and rotate the key to the accessories the barrel should be come lose and gentle be pulled out.
please note that if the internal locking mech is not correctly depressed you will not be able to remove the barrel.
also if you have lost you key you will not be ale to remove the ignition barrel and will need to get a lock smith to rplace the whole thing witch can cost from $120 up to $250 depending on the locksmith

Jan 02, 2013 | 1998 Holden VT Commodore

1 Answer

Key is stuck in the ignition


you will have to dismantle the cowelling from the steering surround then remove ignition barrel to replace as your barrel is likely to be unusable

Oct 13, 2009 | 2005 Buick LaCrosse

1 Answer

Ingine will not turn off after taking keys out . Everything else goes out but ingine keeps running.


Sounds like a faulty ignition barrel! If you take off the trims underneath the steering column you'll be able to gain access to the ignition barrel casing where the key goes. By undoing the casing you'll be able to turn off the engine with a simple flat bladed screwdriver.

Ignition barrels arent too expensive to have replaced, the other problem that might occur is the chance of needing a new set of keys or to have your current keys programmed to the new barrel (Normally a new set of keys is the common procedure with a new barrel)!

Hope this helps

May 24, 2009 | 1994 BMW 3 Series

Not finding what you are looking for?
2005 Daewoo Lacetti 1.4 Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...