Question about 2005 Hyundai Terracan

Open Question

Hyundai 3.5 v6 head tension

Head bolt tension 2002 model

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2039 Answers

SOURCE: Hyundai Sonata 2002 EF-B V6 2.7L

put the bad coil in the place of a good on and check it after that our be sure hope it help fixya our post thanks pierre

Posted on Jul 15, 2008

Ad
  • 74 Answers

SOURCE: need to know all head bolt tension settings for

51 to 54 foot pounds for a cold engine. 58 to 61 for a warm engine.

Posted on Dec 08, 2009

  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

  • 163 Answers

SOURCE: does anyone know the head

The Sequence is as follows:

<----Camshaft Sprocket
8 - 6 - 1 - 3 - 9
10 - 4 - 2 - 5 - 7

Tighten the 10mm bolts to 22ftlbs as you get to them in the sequence and the 12mm bolts to 26ftlbs.

Then go around the sequence again tightening every bolt an additional bolt 60 degrees.

Once again go around the sequence again tightening every bolt an additional bolt 60 degrees.

And you should be done.

Posted on Dec 20, 2010

  • 51 Answers

SOURCE: Could you advise what are

let me see if i can get some info 4 you.

edit
REMOVAL

1. Drain the coolant and disconnect the upper radiator hose.
2. Remove the breather hose (between the air cleaner and the head cover).
3. Remove the air-intake hose.
4. Remove the vacuum hose, fuel hose and coolant hose.
5. Remove the cables from the spark plugs. The cables should be removed by holding the boot portion.
6. Remove the ignition coil.
7. Remove the power steering oil pump and bracket.
8. Remove the intake manifold.
9. Remove the heat protector and exhaust manifold assembly.
10. Remove the coolant pump pulley and the crankshaft pulley.
11. Remove the timing belt cover.
12. Remove the timing belt tensioner pulley.
13. Remove the timing belt.
14. Remove the head cover.


15. Remove the cylinder head assembly. The cylinder head bolts should be removed by using Special Tool, Cylinder Head Bolt Wrench (09221-32001) or equivalent, in the sequence as shown in the illustration in two or three steps.
16. Remove the gasket pieces from the cylinder block top surface and cylinder head bottom surface. NOTE: Make sure that the gasket pieces do not fall in the engine.

INSTALLATION

1. Clean all gasket surfaces of the cylinder block and the cylinder head.
2. Install a new cylinder head gasket onto the cylinder head assembly. Apply sealant to the gasket and do not reuse the old cylinder head gasket.


3. Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
4. Install the timing belt tensioner pulley.
5. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
6. Adjust the timing according to "Timing Belt"
7. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

8. Install the timing belt cover.
9. Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
10. Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
11. Install the surge tank and tighten the nuts bolts to the specified torque.
12. Install the power steering oil pump and bracket.
13. Install the ignition coil.
14. Install the air intake hose.
15. Connect the vacuum hose, fuel hose and water hose.
16. Install breather hose.

Posted on Jun 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Head bolts setting for megane 2.0 l 16v. Ide f5r engine anybody please. In neuton metre not angle please. But angle will do. Please


you could possibly get the tensions by going google and typing in--- head tension s for renault megane 2.0 l engine
torque settings in ft/lbs or newton meters is a by gone thing as the better method of stretching the bolts is to do it by angles
by using a torque wrench the bolt stretch ( tension) has variables like bolt thread finish, thread lubrication, bolts bottoming out from gunk/oil in the hole , uncalibrated tension wrenches , all of which means that not all head studs are pulled down to the correct stretch
By using angles , the head tension becomes uniform

Sep 06, 2015 | Cars & Trucks

1 Answer

F77 2.8 diesel non turbo.1989 model.require head bolt tensions,stages and sequence please


Search Results

    F77 2.8 diesel non turbo.1989 model.require head bolt - Fixya

    www.fixya.com/cars/t25792470-f77_2_8_diesel_non_turbo_1989
    Jul 22, 2015 - f77 2.8 diesel non turbo.1989 model.require head bolt tensions,stages and sequence please - Daihatsu Rocky question. ... Torque to yeild bolts need to be replaced whenever the head comes off.....Long bolts are 46 ft lbs. and ...

Jul 22, 2015 | Daihatsu Rocky Cars & Trucks

1 Answer

Tension figures for head gasket bolts


instructiones should have been in the head gasket kit.. if not the parts store can give the specs to you..

Dec 15, 2013 | Cars & Trucks

1 Answer

I need a video showing me how to loosen the tensioner on a 2002 ford esvort zx2


Do you want to retract the tensioner to change the serp. belt or replace it. Most tens. have a large spring and on the arm where the pulley is some have a 3/8" or 1/2" socket pocket for a tool to fit in, others use the bolt head on the pulley, where others just want you to guess. Most of the chain parts houses loan/rent the tool kit to do this.

Feb 25, 2013 | Cars & Trucks

1 Answer

I need to change the tensioner on serpantine belt help its a citreon berlingo 19 d forte 2002 model


right firstly remove the plastic cover on the inner wing ,then with vehicle on a stand with engine side up a bit turn the wheel to the right to allow access ,now laying on your side look up and their are two tensioners ,one is spring loaded with a 15mm spanner head and the other has a 8mm allen headed bolt with a 1/4 square hole to twist it around,now if the noise persists when the belt is removed then its a timing belt or the water pump thats driven by the timing belt .if noise stops with fan belt off then its either a tensioner pulley or in worst case scenario a alternator or even more costly the power steering pump.to remove the top tensioner pulley then you will need to lower the engine by putting a jack with a block of wood under the sump taking the weight and removing the engine mounting ,three torq headed bolts and a strap over the body sound mount 2 13 mm bolts and then a sort of stool type mushroom headed rubber thing under this is a 16mm bolt ,with engine loose you lower the engine enough to take the top tensioner pulley off this is a left handed thread by the way ,now what i do is to remove the seals in the tensioner pulleys and wash out with some petrol and blow with airline ,oil with engine oil and then work some water resistant grease into the bearings ,refit the cover and as good as new ,thi bearing is not sold separatly but as a complete spring loaded tensioner assembly which is about 35 +tax trade price ,the lower one is about 60 euros +tax (21%) the alternator costs 128euros incl tax and power steering pump costs 185 euros incl tax ,when refitting the belt leave the bottom tensioner slack ,fit the belt then turn the tensioner with a 1/4 square drive and when it tightens the belt tighten the centre lock nut .I can do this quicker than i write about it thats for sure ,nice jam jar these motors the americans dont know what a good motor their missing here with their mammoth engined gas guzlers

Sep 30, 2012 | Cars & Trucks

1 Answer

What makes the tensioner (The one on top next to the fan) Bolt to snap? It has broken twice already. 1.9 TDi Audi 2002 model


To much tension on a faulty bolt. Go to the hardware store and get a grade 8 or better bolt. This one wont snap

Apr 26, 2011 | Audi A4 Cars & Trucks

1 Answer

Where's the belt tensioner for a Mazda Protege 2000? I have a squeak when I turn on the heater. Fan belt needs tightening I'm guessing.


If it's the same as my sister's 2002, there are two belts. The tensioner for the outer belt is on the front, under the power steering pump or ac compressor(cant remember which is on the front there). Loosen the one that locks it in place, and the pivot point bolt on top, then the long one can be turned to adjust tension. All 3 of those bolts are 14mm heads. For the inner belt, it's a pain. It is in the rear, under the alternator. 12 mm for that tensioner and lock out bolt.

Dec 10, 2010 | 2000 Mazda Protege

1 Answer

Need to replace Serpentine belt and p/s belt on my 2002 honda odyssey is this complicated?


the procedure is as follows:-- You have to do it from underneath the vehicle. Take off the rivets to the two plastic covers, and then you will be able to see the tensioner for the belt. Use a 3/4 inch wrench on the tensioner (don't put it on the bolt that holds the tensioner on), and pull it toward the vehicle. The belt will loosen, and you can take it off. As a car owner, you know how important the belt tensioner is for your 2002 Honda Odyssey. However, internal parts wear and damage will loosen or seize the tensioner wheel, causing the belt to slip and make noise. Eventually, the belt may break, shut down the engine and lead you into a serious traffic accident. Before that happens, replace the tensioner on your Honda model and save yourself a lot of problems:---- Remove the Drive Belt:-- 1)Look for the drive belt routing diagram on your vehicle's engine compartment. This is a black and white label, about 4 by 6 inches, usually attached to the radiator shroud or near the strut towers inside the engine compartment. This diagram will be your guide when reinstalling the drive belt. If cannot find one, make a simple sketch on a piece of paper. 2) Insert a belt-tension release tool, or similar tool, into the auto-tensioner arm. 3)Rotate the auto-tensioner arm counterclockwise and slip the belt off the tensioner pulley. 4) Release the auto-tensioner but do not let it snap back in place. 5) Remove the drive belt from the engine compartment. Replace the Belt Tensioner 1) Unscrew the two auto-tensioner mounting bolts using a ratchet, ratchet extension and socket. Note the location of each bolt because they are of different size. 2) Remove the old auto-tensioner from the engine compartment. 3) Set the new auto-tensioner in place and start the two mounting bolts by hand. Make sure you install the bolts in their original place. 4) Start tightening the bolts until they hit the stop using the ratchet, ratchet extension and socket. 5) Torque the two bolts using a torque wrench. Torque the small bolt to 16-foot pounds [22 Nm] and the large bolt to 47-foot pounds [64 Nm]. This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Mar 01, 2010 | 2002 Honda Odyssey

1 Answer

Need head bolt,intake upper and lower and rocker arm torque lbs.


Head bolts--------- 22 ft lbs.
Intake upper------ 18 ft lbs.
Intake lower------- 10 ft lbs. Tighten vertical bolts first, the diagonal bolts, failure to do this will result in an oil leak.
As far as the rocker arm bolts, they have to be adjusted with the valves closed, tighten down just enough to turn the push rods with your fingers with slight tension.
This is out of a Technical Specifications Manual.

Jul 30, 2009 | 2002 Pontiac Grand Am

Not finding what you are looking for?
2005 Hyundai Terracan Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...