Question about Cars & Trucks

Open Question

Drive axle wheel bearing torque for1995 GMC topkick 7000

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: changing front wheel bearing

first take the wheel off
Then take the caliper off the rotor
Then take the rotor off the CV joint spindle
You will need to remove the three bolts that hold the bearing in place.
You will either need to remove the two bolts that hold the strut or
you will need a Puller.

Posted on Apr 01, 2009

Rayvin1943
  • 97 Answers

SOURCE: 1994 gmc rear axle removal how to

-Remove tire and brake drum
-put drain pan under axle housing
-remove rear axle housing cover (10 or 12 bolts)
-turn gear untiil the bolt for cross shaft shows and remov e the bolt
-remove the cross shaft.
-push axle in until you can remove "U" clip from axle and axle will pull out,
Remove seal, you need a pulller to remove axle brg.

Posted on Jul 26, 2009

canbruce75
  • 1776 Answers

SOURCE: I need the torque spec for the axle and the axle

Go to the autozone.com website and register there. It doesn't cost anything and you will have access to an online repair manual for the vehicle. (Kinda handy) They have a specification section, so the torque specs might be found there. Hope this helps and best wishes.

Posted on Aug 18, 2009

Testimonial: "hey thanks for the help"

  • 4 Answers

SOURCE: how tight should i make the axle nut after fitting

tighten the nut down and spin the hub to set the bearings and then back it of a 1/4 turn

Posted on Nov 13, 2009

  • 13 Answers

SOURCE: proper torque for bolts on front wheel

The axle nut spec is 177 foot lbs. and the bearing to knuckle bolts spec is 133 foot lbs.

Posted on Dec 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for a front wheel bearing?


if its not a drive axle and only has a castle nut with a cotter pin , then regrease the wheel bearings and run nut all the way in to its hand wrench tight (not impact gun), turn wheel one or two full turns to seat it , then back castle nut off two spaces and install cotter pin , this s\is std way to set proper spacing on wheel bearings

if its a drive axle consult your cars model and make and year torque specs book

Mar 29, 2016 | Cars & Trucks

1 Answer

2002 pt cruizer changed both front wheel bearings and long axle rightside now there is a humming noise on drivers side when driving and ideas thanks


It is entirely possible to have a bad replacement wheel bearing. There are many cheap ones available and I've found that you get what you pay for. I prefer Timken bearings myself. Also, the drive axle nut torque is critical in ensuring that you don't cause bearing failure. Too loose or too tight will cause bearings to fail in short order. The axle nut is not one that can be "shade tree torqued" by "grunt-power".

Jun 29, 2015 | Cars & Trucks

1 Answer

What are the torque specs for a front axle bearing/hub?


Not sure about your model, but in general they are usually around 180 ft./lbs.

Aug 01, 2014 | 2003 Chevrolet Silverado 1500

1 Answer

Torque specs axle nut


Wheel nut torque 140 lb ft

Dec 31, 2013 | Cars & Trucks

1 Answer

How to assemble a front wheel bearing on a 2003 GMC Sierra 1500 4x4


The front wheel bearing is a hub and bearing assembly. To remove you will.... 1. Remove the tire 2. Remove the axle nut. You can put a punch in the fins of the rotor to keep the assembly from turning while you rmove the nut. You can can do the same thing when you torque the axle nut. 3. Remove the caliper and rotor. 4. Unplug the abs sensor if equipped. 5. Remove the three bolts that hold the hub to the knuckle. 6. Rmove the hub. If you need torque specs let me know and i'll get them for you. It is absolutely critical that you torque the axle nut to the proper spec!

Oct 08, 2011 | Cars & Trucks

2 Answers

Replace front left wheel berring on 2002 GMC Yukon


do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

Jan 03, 2010 | 2002 GMC Yukon XL

1 Answer

Proper torque for bolts on front wheel


The axle nut spec is 177 foot lbs. and the bearing to knuckle bolts spec is 133 foot lbs.

Dec 23, 2009 | 2004 GMC Yukon

1 Answer

I need the torque spec for the axle and the axle nut for the front wheel bearing. 2004 gmc yukon 4.8 ltr. 4wd.thank you


Go to the autozone.com website and register there. It doesn't cost anything and you will have access to an online repair manual for the vehicle. (Kinda handy) They have a specification section, so the torque specs might be found there. Hope this helps and best wishes.

Aug 17, 2009 | 2004 GMC Yukon

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...