Replacing air conditioning passenger air filter

Cabin Air Filters are usually located behind the passenger glove compartment. Remove that and you should find your cabin air filter.

in most cases the cabin air filter is located under the dash on the passenger side of the car. in any case it will be "in line" with your hvac ducting

try changing your cabin filter, it is located in front of the passenger, under the hood and just below the passenger side windshield wiper-just open the plastic door, there it is...

The oil filter is underneath the engine passenger side, at the back of the air conditioning compressor
&&
The oil drain plug is under the passenger side of the engine, it is on the posterior-inferior portion of the oil pan.



Hope this helps

Positive Feedback ALWAYS welcome :)

How to Replace an AirConditioner Filter on a 2002 ToyotaAvalon

The air conditioner filter onthe 2002 Toyota Avalon is more commonly referred to as the cabin air filter.The filter does more than just regulate the flow of air: It also filters outpollen, dust, exhaust fumes and air pollution. Because it directly affects thelevel and quality of air coming into the passenger cab through the interior airvents, it can compromise the performance of the air conditioning, as well asthat of the heating system, if not changed at regular intervals.

1. Openthe Avalon's passenger's side door. 2. Open the glove box and removeits contents. 3. Locate the stop screw on the right side ofthe glove box, and remove it with the Phillips-head screwdriver while bracingthe bottom of the glove box. 4. Gently swing the glove box downward andlet it hang upside-down towards the passenger's side floorboard. 5. Locate the white filter frame, now visiblefrom behind the original glove box's position. 6. Push the tabs at each end of the filterframe inward to unlock it, then pull the tray and filter assembly out of thecabin air filter housing. 7. Remove the oldfilter from the tray, then install the new one, making sure to tuck the ends ofthe replacement filter under the tabs on the left and right sides of the tray. 8. Reinsert the trayand filter assembly into the filter housing; push it until the tabsautomatically lock the door of the tray into place. 9. Reassemble theglove box by lifting it up, replacing the stop screw and then returning itscontents before closing it.
you may check at www.ehow.com just type how to replace an air conditioner filter of a 2002 Toyota Avalon..

do you mean the cabin filter?
If you do, then the filter is located under the glove compartment or on the passenger side under the hood under a plastic shroud.

Check your manual.

id suggest replacing the air filter the filter is located in the cannister its black usually square has a plastic accordian hose that goes to it and its usually on the passenger side of the car under the hood.also it can be located on the passenger side.

You will need to recharge your system , go to the nearest parts store and buy what ever brand that is recomended, and attach it to the lower air conditioning recharge valve.

may be just a cable adjustment.


SECTION 412-01: Air Distribution and Filtering 2001 Focus Workshop Manual DESCRIPTION AND OPERATION Air Distribution and Filtering The new heating and ventilation system ensures even air distribution.
The temperature control and air distribution flaps are controlled by two operating cables. All vehicles have a recirculated air function, with the flap controlled by a servo motor.
Air is supplied to the windscreen and side windows regardless of the air distribution setting.
The clean air filter is fitted as standard in most countries. This cleans the incoming fresh air of pollen and dirt particles. It must be renewed after every 40,000 km under normal operation conditions, or after 20,000 km under difficult conditions. If no clean air filter is installed, a plastic grille is fitted over the air intake. This can easily be replaced with a clean air filter.
Air distribution operating switch
Face level The main flow of air enters the passenger compartment at face level.
Face level/floor level The main flow of air enters the passenger compartment in equal parts at face level and floor level, and a small amount flows to the demister nozzles of the side windows.
Floor level The main flow of air enters the passenger compartment at floor level, and a smaller amount flows to the demister nozzles of the side windows.
Demist/floor level The main flow of air enters the passenger compartment in equal parts at the windscreen and at floor level, and a smaller amount flows to the demister nozzles of the side windows.
Demist The main flow of air enters the passenger compartment at the windscreen and a smaller amount flows to the demister nozzles of the side windows.
Air distribution operating switch Air distribution operating cables
NOTE: The Bowden cables for LHD and RHD vehicles are identical. However, they are fastened to the air flap operating mechanism with the respective reverse side of their connectors.
The air distribution switch operates with two Bowden cables. The cables operate the air distribution valves in the heater housing.
To remove and install the cables, the rotary switch must be turned as far as it will go to the left. The air flap mechanism engages easily in this position, making the installation of the cables easier.
--------------------------------
Air Distribution Cable Control Assembly Removal
CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the radio/cassette unit and the CD player (if equipped). For additional information, refer to Section 415-01 .

1. Remove the bezel with heater/air conditioning controls.

1. Remove the bezel with heater/air conditioning controls (continued).
   • Pull off seven electrical connectors (six shown).

1. NOTE: To remove the Bowden cables, turn the rotary switches as far as they will go to the left.
   Remove the bezel with heater/air conditioning controls (continued).
   • Unclip the Bowden cables.

1. Remove the lower driver's side footwell trim.

1. Unclip and remove the air distribution Bowden cables.

1. Unclip and remove the temperature control Bowden cables.
   • Unclip and remove the temperature control Bowden cables.

Installation

1. NOTE: Route the new Bowden cables without kinks and check for easy accessibility.
   NOTE: To install the Bowden cables, turn the rotary switches as far as they will go to the left. The mechanism engages easily in this position.
   NOTE: The Bowden cables are identical for RHD and LHD vehicles, although they are fastened to the air flap operating mechanism with the reverse side of their connectors.
   Install the components in reverse order.

1. Check operation of the Bowden cables.
   

It's located behind the glove box in the passenger seat of the vehicle. Visit HondaPilot.org to see step by step procedures for replacing the cabin filter.