Question about 2000 Dodge Caravan

2 Answers

3.0L Dodge Caravan Starter diagram

To remove Starter/Solenoid Assembly from motor- diagram of bolt locations?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Take a look on drivers side of engine. hard to see and should be two bolts holding to engine. take it loose after taking loose the electrical connections from below.

Posted on May 15, 2014

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 790 Answers
Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 187 Answers

SOURCE: locate bolts to remove the strater of 1996 dodge caravan

Almost all starters have ears with holds in them that bolts go through to threaded holes in the bell housing. Find the starter and look around the end without the wires for the bolts.

Posted on May 07, 2009

  • 40 Answers

SOURCE: Replacing the starter on 2001 Dodge Grand Caravan

with most front wheel drives you must remove the passenger tire and reach through to the starter bolt with an extension and if I remember write with a 15 mm socket you can reach through and take out the bolt

Posted on Jun 20, 2009

  • 1 Answer

SOURCE: How to remove the harmonic balancer pulley on a

i have a 1998 caravan my harmonic balancer fell off my qquestion is is there 2 separate keys that hold on the timing gear and the balancer pulley on, i have been to the dodge dealer and they printed me out pics but i still don't know for sure if the timing gear has it's own key or there is just 1 long key that holds both the timing gear and the balancer ......PLEASE HELP

Posted on Jan 06, 2010

csmock132
  • 4669 Answers

SOURCE: 1994 Dodge Caravan solenoid

The starter solenoid is bolted to the starter.

Posted on May 13, 2010

  • 373 Answers

SOURCE: 1994 Caravan: where is the starter solenoid located on a 1994 do...

The starter solenoid motor assembly is located on the lower part of engine next to the transmission bellhousing. Hope this will help you.

Posted on May 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starter diagram for a 1994 dodge intrepid


3.3L Engine
  1. Disconnect the negative (-) battery cable. Raise and safely support the front of the vehicle on jackstands. Fig. 1: Disconnect the negative battery cable 88172g31.gif

  2. Remove the three bolts attaching the starter to the engine/transaxle. Fig. 2: Remove the three starter mounting bolts 88172g32.gif
    CAUTION
    Be careful when removing the starter motor mounting bolts, the motor can be quite heavy. Personal injury could result if the starter motor falls from its mounting position.
  3. Remove the starter from the the transmission housing. Position the starter to gain access to the wiring connectors.
  4. Remove the battery positive cable nut from the starter and remove the cable. Fig. 3: Remove the battery positive cable nut from the starter and remove the cable 88172g33.gif

  5. Disconnect the push on solenoid connector.
  6. Remove the starter from the vehicle. To install:
  7. Clean all wire terminals of dirt, grease or corrosion.
  8. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  9. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  10. Lower the vehicle.
  11. Connect the negative (-) battery cable.
3.5L Engine
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. For easier servicing, do not remove the wiring from the starter motor at this time.
  4. Remove the three bolts attaching the starter to the engine. Fig. 4: Remove the three bolts attaching the starter to the engine 88172g34.gif

  5. Remove the starter solenoid assembly from the transfer housing. Position the starter to gain access to the wiring connectors.
  6. Remove the battery positive cable nut from starter and remove the cable.
  7. Disconnect the push on solenoid connector.
  8. Remove the starter from the vehicle. To install:
  9. Clean all wire terminals of dirt, grease or corrosion.
  10. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  11. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  12. Lower the vehicle.
  13. Connect the negative battery cable.
prev.gif next.gif

Oct 15, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

How do I install a starter on a 2001 dodge caravan starter?


Lift up the front of your car. Disconnect the (+) cable of the battery. The starter is located in front under vehicle with cylindrical shape. Remove the cable of the starter and solenoid. Remove two bolts that secure starter to engine. Pull the starter to disengage the pinion from the fly wheel.

Oct 13, 2010 | 2001 Dodge Grand Caravan

2 Answers

How to remove starter


Removal & Installation - Starter
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle assembly
    Electrical connections Torque converter cover Starter
To install:
  1. Install or connect the following:
    Starter. Torque the bolts to 35 ft. lbs. (47 Nm). Torque converter cover Solenoid -BAT- terminal. Torque the nut to 89 inch lbs. (10 Nm). Solenoid -S- terminal. Torque the nut to 27 inch lbs. (3 Nm). Radiator air baffle assembly Negative battery cable
  2. Perform a charging system test and verify the starter is operating properly
8e0154d.jpg

Fig. Showing the starter motor location and electrical connections
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle, for clearance if necessary Flywheel inspection cover bolts Flywheel inspection cover Electrical connections from the starter motor Starter motor mounting bolts Starter motor
To install:
  1. Install or connect the following:
    NOTE Before installing the starter motor to the engine, tighten the nut next to the cap on the solenoid BAT terminal. If this terminal is not tight in the solenoid cap, the cap may be damaged during installation of electrical connections and cause the starter motor to fail later.

    Starter motor Starter motor mounting bolts and tighten the bolts to 30 ft. lbs. (40 Nm) Electrical connection to the battery terminal on the solenoid and tighten the battery terminal nut to 13 ft. lbs. (17 Nm) Electrical connections to the S terminal on the solenoid and tighten solenoid S terminal nut to 27 inch lbs. (3 Nm) Flywheel inspection cover Flywheel inspection cover bolts Radiator air baffle, if removed
  2. Connect the negative battery cable

Hope helps, remember rated this.

Aug 12, 2010 | 2001 Pontiac Montana

2 Answers

Where is the starter on a 1999 s-10


passenger side, under exhasut pipe, against motor, close to tranni.

Jul 17, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

1994 Caravan: where is the starter solenoid located on a 1994 do...


The starter solenoid motor assembly is located on the lower part of engine next to the transmission bellhousing. Hope this will help you.

May 17, 2010 | 1994 Dodge Caravan

1 Answer

1994 Dodge Caravan solenoid


The starter solenoid is bolted to the starter.

May 07, 2010 | 1994 Dodge Caravan

1 Answer

Need to replace the starter on a 1997 dodge grand caravan


to remove the starter from motor you need to disconnect the battery negative wire from the battery. then remove the battery wire and start wire from solenoid. remove the bolts holding the starter to the transmission bellhousing. then remove starter. installation is the reverse of removal.

Apr 28, 2010 | 1997 Dodge Caravan

2 Answers

How to take out the starter


Chrysler Caravan/Voyager/Town and Country 1996-1999 Starter - REMOVAL & INSTALLATION(see Figures 7, 8, 9, 10 and 11)

7d28ee2.jpg

Fig. 7: Disengage the solenoid wiring connector, then the battery positive (B+) nut and wire from the starter motor

ac6bf44.jpg

Fig. 8: Remove the 3 starter motor-to-transaxle bellhousing mounting bolts

1d4f6fd.jpg

Fig. 9: Remove the starter motor from the vehicle

d9e9e14.jpg

Fig. 10: After removing the starter motor, examine the teeth of the flywheel for excessive wear or damage. Repair if necessary

b56ba8b.jpg

Fig. 11: If the old starter is going to be re-installed, check the condition of the pinion gear teeth. Replace the starter if the pinion gear shows excessive wear or damage
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Disengage the solenoid wiring connector from the terminal. This connection may be held in place by a retaining nut, or it could be a push-in connector.
  4. Remove the B+ nut and wire from the starter motor terminal.
  5. Remove the starter motor-to-transaxle bellhousing mounting bolts.
  6. Remove the starter from the vehicle. If equipped, remove the starter motor spacer.
To install:
  1. If equipped, hold the starter motor spacer in position.
  2. Install the starter motor into position on the vehicle.
  3. Install the starter motor-to-transaxle bellhousing mounting bolts. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  4. Engage the solenoid wiring connector onto the starter terminal.
  5. Connect the B+ wire and tighten the retaining nut to 90 inch lbs. (10 Nm).
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Verify starter motor operation.

Hope this help (remember comment and rated this).

Apr 20, 2010 | 1996 Dodge Caravan

1 Answer

Where is starter located and how to remove it , for a dodge caravan 1998,3.3l


Starter - Removal & installing
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Disengage the solenoid wiring connector from the terminal. This connection may be held in place by a retaining nut, or it could be a push-in connector.
  4. Remove the B+ nut and wire from the starter motor terminal.
  5. Remove the starter motor-to-transaxle bellhousing mounting bolts.
  6. Remove the starter from the vehicle. If equipped, remove the starter motor spacer.
To install:
  1. If equipped, hold the starter motor spacer in position.
  2. Install the starter motor into position on the vehicle.
  3. Install the starter motor-to-transaxle bellhousing mounting bolts. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  4. Engage the solenoid wiring connector onto the starter terminal.
  5. Connect the B+ wire and tighten the retaining nut to 90 inch lbs. (10 Nm).
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Verify starter motor operation.
020fef8.jpg

Disengage the solenoid wiring connector, then the battery positive (B+) nut and wire from the starter motor

98933b2.jpg

Remove the 3 starter motor-to-transaxle bellhousing mounting bolts

e2afde4.jpg

Remove the starter motor from the vehicle


The starter relay is located in the Power Distribution Center (PDC) in the engine compartment. Refer to the underside of the PDC cover for starter relay location.

Hope helped with this (remember rated this help) Good luck.

Nov 18, 2009 | 1998 Dodge Grand Caravan

1 Answer

Where is the starter on a 98 dodge gr caravan


Remove the air cleaner box and hoses. The starter is located near the bottom of the engine where it connects to the transmission assembly. It is accessed by jacking up the front of the car and working underneath. Remove the battery negative cable to prevent big sparks! Be sure to use jack stands under the car while working there. There are three bolts to remove and several wires to the solenoid. Watch for a spacer that, if used, will fall out when the starter is removed.

Oct 13, 2009 | 1998 Dodge Caravan

Not finding what you are looking for?
2000 Dodge Caravan Logo

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...