Question about Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The headlights on the envoy are the easiest parts of the car to repair. You just pull the two tabs at the top of the headlights, screw out the bulb containers and you are good to go
Posted on Nov 15, 2008
If I remember correctly if you look at the back side of the fuse cover, it should tell you what the fuses are. Also in the owners manual in the index, under fuses, it should give you a diagram of the fuse location for the acc. outlets. Good luck. The fuse should be a 20 or 25A fuse.
Posted on May 26, 2009
A: Use two jack-stands under the front-frame rails, a hydraulic jack under the "bulb" in the control-arm and a third jack-stand under the "spindle extension" of the rotor. It's not necessary to remove the calipers and/or rotors. The upper strut-mounts might need to be forcibly loosened and then removed. If the old struts are worn out enough, they should just compress by themselves. The new struts should be able to be compressed by hand and then positioned in place as fast as possible, before they extend.
For the strut-to-knuckle bolts to loosen, use a pipe extension to the fixed driver of the socket-set. To tighten these bolts, first torque them to 170 Nm and then give them an additional turn of 120 degrees. For the latter, use the pipe-extension again
Posted on Jun 29, 2009
don't need any special tools, standard sockets sets, "C" clams is a must unless your a He-Man and wrench set, plyer or needle nose will do. I assumed being 2003 your rotor never have been turn and i recommend every time you change your bakes is good idea to have your rotor turn. reason is it will make your pad last lot longer, removed any vibration and better even wear on the pad and eliminate any squealing although is not necessary to do so. make sure you get extra break fluid to bleed the brakes. get your self 5 feet long smallest vacum rubber hoses and a glass jar to bleed your brake fluid in. the rubber vacum hose you going to use to fit on to the bleeding nipple and run the other end of line to your the glass jar to save the brake fluid when you bleed the brakes. when removing caliper, check inspect make sure the rubber seals around your piston look good and not crack or deteriorated. before applying new pad make sure you open the bleed valve to reduce the pressure by turning the bleed nipple counter clockwise and leave it open attach that rubber hoses to the nipple because you going to press on the piston back into it housing with the "C" clamp in order for new pad to fit. becareful not to damage the rubber seals around the piston. its going to take lots of effort to push that piston back in so be a bare with it if needs to. once the pad is back in make sure you keep the reservoir full with brake fluid and then bleed the brake. two people is a good idea to do brake. one will do the pumping the brake and holding it down and other will bleed the nipple. I bleed it 2-3 time will do the job. good luck!
Posted on Jul 17, 2009
after you position the seat that is comfortable for you to drive then press and hold the 1 button on your door switch and hold it until you hear two beeps then it is programmed
Posted on Jul 19, 2009
Tips for a great answer:
Dec 07, 2016 | 2003 GMC Envoy
Sep 11, 2014 | 2003 GMC Envoy
Jan 29, 2014 | 2003 GMC Envoy
Aug 02, 2012 | 2003 GMC Envoy Xl
Jul 21, 2011 | 2003 GMC Envoy
Jan 21, 2011 | 2002 GMC Envoy
Dec 09, 2010 | 2003 GMC Envoy Xl
Jun 09, 2009 | 2003 GMC Envoy
18 people viewed this question
Usually answered in minutes!