Question about Cars & Trucks

2 Answers

Hi I need torque settings for crankshaft main bearings on my celica 1.8 vvti can u help

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 4 Answers

What year is It

Posted on May 14, 2014

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 15,557 Answers

WHAT YEAR?

Posted on May 14, 2014

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michael_grey
  • 365 Answers

SOURCE: engine bearing torque settings big end and main bearing

4 cylinder correct?
1bac25a.jpg

Posted on Jun 20, 2009

  • 548 Answers

SOURCE: Toyota celica vvti key programming

Put key in ignition. Hold down one of the key buttons and hold it down while you turn the ignition on. Door locks should pop up and down. Then release button and remove key.

Posted on Sep 03, 2009

Testimonial: "Thanks for the feedback. . is this programing done using the new key first or do i need to use my old key to start the Programming process thanks"

hardinfarms
  • 144 Answers

SOURCE: 2003 mazda 6 3.0 need the main bearing torque specs

I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Posted on Oct 05, 2009

Testimonial: "thank you so much! couldnt find this information anywhere, even called the local mazda dealers!"

  • 91 Answers

SOURCE: need torque settings for big end and main bearing

big end - stage one 18-22 Nm. stage 2 40-50 degrees
main bearings stage 1 20 Nm stage 2 90 degrees

Posted on Dec 16, 2009

Dirt Dobber
  • 253 Answers

SOURCE: need torque for a 2000 Toyota Celicia GT 1.8L

Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque for main bearings on a 2002 3.7 ltr. liberty?


the book is free to read? KJ
chapter 9s
(7) Before installing bolts, lubricate the threads
with clean engine oil, wipe off any excess oil.
(8) Install main bearing bedplate to engine block
bolts 11, 17 and 20 finger tight. Tighten these bolts
down together until the bedplate contacts the cylinder
block.
(9) To ensure correct thrust bearing alignment,
perform the following steps:
² Step 1: Rotate crankshaft until number 4 piston
is at TDC.
² Step 2: Move crankshaft rearward to limits of
travel.
² Step 3: Then, move crankshaft forward to limits
of travel.
² Step 4: Wedge an appropriate tool between the
rear of the cylinder block (NOT BED PLATE) and
the rear crankshaft counterweight. This will hold the
crankshaft in it's furthest forward position.
² Step 5: Install and tighten bolts (1-10) in
sequence shown in (Fig. 49) to 41 N·m (30 ft. lbs.).
² Step 6: Remove wedge tool used to hold crankshaft.
(10) Tighten bolts (1-10) again to 41 N·m (30 ft.
lbs.) PLUS 1/4 turn in sequence shown in (Fig. 49).
(11) Install main bearing bedplate to engine block
bolts (11-20), and torque each bolt to 28 N·m (20 ft.
lbs.) in sequence shown in (Fig. 49).
(12) After the main bearing bedplate is installed,
check the crankshaft turning torque. The turning
torque should not exceed 5.6 N·m (50 in. lbs.).

why not just read the chapter, here.

http://colorado4wheel.com/manuals/Jeep/KJ/

Jan 17, 2017 | 2002 Jeep Liberty

1 Answer

Full engine torque settings for toyota corolla 1.4 vvti 2001 model


main bearing
tighting in the following stages:
22Nm then 44 Nm then 45 degree then 45 degree
big end bearing
20 Nm then 90 degree

Apr 05, 2014 | 2001 Toyota Corolla

1 Answer

Torque settings on cranck sharf bearings


Torque settings for V-6 engine.
Main bearing cap bolts torque:
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Connecting rod cap bolts torque:
Torque: 24.5 N·m (250 kgf·cm, 18 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Feb 11, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

Mar 02, 2011 | 1989 Honda Civic

1 Answer

Hello and help, I need the main bearing, big end and flywheel torque settings for an Isuzu 3.1 td 1997, my manual only seems to have v6 petrol engines in it for some reason. many thanks Ron...


I have a 1997 Rodeo with the V6 3.2L engine. The crankshaft main bearing caps are torqued to 29(lb-ft).

The crankshaft pully is torqued to 123 (lb-ft).

Feb 26, 2011 | Isuzu Trooper Cars & Trucks

1 Answer

2002 audi tt 225 bhp cranksharft torque settings


Crankshaft torque settings for 2002 Audi TT 225 BHP:

1. Main bearings: Renew bolts = Yes
2. Main bearings: Stage 1 = 65 Nm
3. Main bearings: Stage 2 = 90 degrees
4. Big end bearings: Renew bolts / nuts = Yes
5. Big end bearings: Stage 1 = 30 Nm
6. Big end bearings: Stage 2 = 90 degrees
7. Flywheel / driveplate = 60 Nm + 90 degrees (use new bolts / nuts)
8. Crankshaft pulley / damper centre bolt = 90 Nm + 90 degrees (use new bolts)


Nov 25, 2010 | Audi TT Cars & Trucks

1 Answer

Need torque for a 2000 Toyota Celicia GT 1.8L


Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Mar 18, 2010 | 2000 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...