Question about 1995 Ford Ranger Supercab

1 Answer

Had a new ignition switch installed. Now when I open the door the buzzer buzzes until I close the door. The lights are off and the key is in my hand,not in the ignition.

It never did this before unless I left the lights on or the key was in the ignition, but now it buzzes as soon as I open the door.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 34 Answers

Ig switch improper install.

Posted on May 15, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: 2005 f150 "Door Ajar Light Always On.. Even with all doors shut..

What happens when you remove both switches, and wires? What happens when you use a jumper wire acros both wires, on both doors?

Posted on Feb 25, 2009

  • 141 Answers

SOURCE: Interior Light sometimes will not shut off in Ford Ranger Pick up

If I am not mistaken, the plunger is located in the door with the latch. Most of the time you can just pull the door panel off and adjust the switch. After opening and closing the door, they get knocked out of adjustment. I sincerely hope that this helped you. Take care and best wishes.
Bryon

Posted on Mar 20, 2009

askjhuber
  • 59 Answers

SOURCE: Possible ignition switch problem? 99 Explorer

The door locks wont work when the car is on. Dont spend time chassing this problem beacuse it is tied in with the ignition switch.

Posted on May 16, 2009

Mike258
  • 1498 Answers

SOURCE: 1998 Taurus SE warning chime beeps as you get in the driver door

Hi John,

Had a similar problem with my Saturn. Door chime going all the time, the seat belts going up - down - up for no apparent reason.

Turned out to be the switch in the door jamb had become unseated. As it randomly made and broke contact, the cars computer thought the doors were opening and closing, then acted accordingly.

I remounted it with the help of a hot glue gun (plastic mount).

Hope this info helps with your problem.

Best regards
Mike

Posted on Aug 19, 2009

  • 564 Answers

SOURCE: Dome light stays on afrter the door is shut

in the door jam there is a switch it sounds like the switch either needs to be adjusted or replaced to adjust loosen the big flat screw at the bottom and turn the switch to acheive the right height. if it is at the correct height then try a new switch. this should solve that problem if not then you have me stumped also.

Posted on Nov 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Interior light buzzer won't stop 1990 mazda miata


Actually, it's just an simple buzzer associated with the seatbelt circuit and doors. Many of us with Miata's have just removed it as it's easy to do. It's located under the dash on the driver's side and easy to remove
  • put the key in the ignition and open the door
  • reach up under the dash to the left of the steering wheel and grab small rectangular plastic boxes until you feel the one that buzzing and vibrating
  • Now feel around for the latch that holds it into place - it's a squeeze-to-release type
  • Open the latch and pull off the wiring harness
  • Use a twist tie or some electrical tape to tape the wire harness to something so it doesn't bounce around.
Done!

Apr 19, 2013 | 1990 Mazda MX-5

1 Answer

Is there a buzzer for the lights on 2003 jetta?


depends on market....key in ignition open door, buzzer....key out of ignition lights on,buzzer.BUT.....pull dipswitch toward you (flasher)with key out NO BUZZER. VW pull out anything that costs to make a car cheaper for any given market.even a cigarette lighter is missing on some cars.......no ashtray in others.....

Jul 11, 2010 | 2003 Volkswagen Jetta TDI

1 Answer

I also have 98 neon with "door ajar" light and buzzer staying on but ONLY when all doors are closed. key doesnt evan have to be in ignition! also the dome light works perfect with the door and light switch...


sounds like their is a short in the wiring to the dome light and buzzer... i know you don't want to hear that... if it is grounded somewhere that is why it quits when you remove the bulb... possible wire caught behind the dash when you put it back together... if so that would cause the ground...

Mar 22, 2010 | 1998 Dodge Neon

1 Answer

I have a 97 gmc jimmy 4wd. received dtc s 740 , 785 ,1860. just recently received 101. I rectified 101 code by replacing air filter and cleaning MAF sensor. I have traced the remaining codes to the...


Have no clue as to what you want ? Like to try an explain a little better . What do DTC'S 740 , 785 and 1860 have to do with key in ignition chimes . Plus i'am assuming the DTC'S you have listed all start with P - P0740 , P0785 and P1860 .
DTC P0740 TCC Enable Solenoid Circuit Electrical (2.2L)
DTC P0740 TCC Enable Solenoid Circuit Electrical (4.3L)
DTC P0785 3-2 Shift Solenoid Circuit Electrical (2.2L)
DTC P0785 3-2 Shift Solenoid Circuit Electrical (4.3L)
DTC P1860 TCC PWM Solenoid Circuit Electrical (2.2L)
DTC P1860 TCC PWM Solenoid Circuit Electrical (4.3L)

None of these have anything to do with warning chimes .

Key-In Warning Buzzer
Voltage is supplied at all times to the truck BCM through the following components:
• The underhood bussed electrical center (UBEC) fuse 4
• CKT 1140 (ORN)
The chime or buzzer sounds if the following conditions exist:
• The key is in the ignition switch
• The vehicle is not running.
• The left door is open.
When the door is open, the LF door jamb switch closes to ground. This provides a ground to the truck BCM through the following components:
• CKT 126 (TAN)
• The left front side door jamb switch
• CKT 1050 (BLK)
• SP203
• C203, cavity F12
• G203
The chime or the buzzer will sound for as long as the door is open and the key is in the ignition switch.


Turn the ignition switch to the OFF position.
Remove the key from the ignition.
Using the scan tool, enter BCM Data List.
Select Input 1.
Does the KEY IN IGNITION test display NO?
3
Turn the ignition switch to the OFF position.
Remove the key from the ignition.
Using the scan tool, enter BCM Data List.
Select Input 1.
Does the KEY IN IGNITION test display NO?
--
Go to Step 4
Go to Step 8
4
Turn the ignition switch to the OFF position.
Remove the key from the ignition.
Move the headlamp switch to the OFF position.
Using the scan tool, enter BCM Data List.
Select Input 2.
Does the PARKLAMPS test display OFF?
--
Go to Step 5
Go to Step 9
5
Inspect the connections at the BCM.
Are the connections in need of repair?
--
Go to Step 6
Go to Step 7
6
Repair the connections as necessary.
Is the repair complete?
--
Go to Diagnostic System Check - Audible Warnings
--
7
Replace the BCM. Refer to Body Control Module Replacement in Body Control System.
Is the repair complete?
--
Go to Diagnostic System Check - Audible Warnings
--
8
Locate and repair the short to ground in CKT 80 between the BCM connector C2 terminal B9 and the key in ignition alarm switch.
Is the repair complete?
--
Go to Diagnostic System Check - Audible Warnings
--
9
Are the park lamps ON with the switch OFF?
--
Go to Exterior Lights System Check in Lighting Systems
Go to Step 5
Your best bet take to a qualified repair shop

Jul 23, 2017 | 1997 GMC Jimmy

1 Answer

When I leave the lights on in my 2001 hyundai elantra, I don't get that buzzing noise when I ope the driver side door. Also, the lights(both map light and driver side door lights) don't turn on when the...


the door switch is corroded - simplethe push button switch (that is pressed when you close the door) it comes out with a Philips screwdriver, undo the screw and pull out the switch it may be a bit stuck but wiggle it and it should pop out, when you look at it you'll know what I mean by "simple" - sand down the brass looking contacts till they're shiny and dab a spot of grease on there and refit the switch, all should be well again. - I quite like the elantra, nice and roomy :-)
Actually before you do this you can open the door with key in, lights on, so buzzer should be on and wiggle the little post that sticks out of the door switch, if you pull it out a little the buzzer should come on proving that the contacts are dirty and not connecting properly.

Jan 25, 2010 | 2001 Hyundai Elantra

1 Answer

Dome light stays on afrter the door is shut And the ''door ajar light comes on And the dome light will not go out. If I take the lamp (bulb) out the door ajar goes out and of couse the light goes out,...


in the door jam there is a switch it sounds like the switch either needs to be adjusted or replaced to adjust loosen the big flat screw at the bottom and turn the switch to acheive the right height. if it is at the correct height then try a new switch. this should solve that problem if not then you have me stumped also.

Nov 14, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Key on engine running trouble code 55


Warning Chime Systems The generic electronic module (GEM) will sound the following warnings:
  • key-in-ignition warning
  • safety belt warning
  • headlamp switch ON warning
  • door ajar warning
------------------------------------------------------------------------------------------------
Headlamp Switch On Warning The generic electronic module (GEM) sounds when the driver door is opened while the headlamp switch (11654) is in the PARK or HEAD position, and continues to sound at a rate of 4 chimes per second until the headlamp switch is turned off or the driver door is closed.
  • When the headlamp switch is in the PARK or HEAD position, power is supplied through Circuit 293 (O/R) to the GEM.
  • When the driver door is open, the driver door open warning lamp switch (10B997)is closed and ground is supplied to the generic electronic module (GEM).
A delayed headlamps on repetitive chime will sound for a period of three seconds beginning twenty seconds after the key is turned to OFF, LOCK or ACC, the headlamp switch is in the PARK or HEAD position, and the driver door is closed. Delayed headlamps on is terminated by opening and closing the driver door again.
---------------------------------------------------------------------------------------
Door/Liftgate Ajar Warning The door/liftgate ajar warning functions as follows:
  • The generic electronic module (GEM) sounds a warning tone for one second when any vehicle door, liftgate window or the liftgate is ajar without any other door already open and the ignition switch is in the RUN position.
  • Power is then supplied through Circuit 627 (BK/O) to the door ajar warning indicator lamp which remains illuminated until all doors are closed or the ignition switch is no longer in the RUN position.
----------------------------------------------------------------------------------------------
Key-in-Ignition Warning The generic electronic module (GEM) sounds when the LH front door is opened with the key in the ignition switch and continues to sound until the key is removed or the door is closed.
  • When the key is in the ignition switch, the ignition key warning switch terminal and wire (11A128) is closed and ground is supplied through Circuit 158 (BK/PK) to the generic electronic module (GEM).
  • When the LH front door is open, the LH front door open warning lamp switch (10B997) closes and ground is supplied through Circuit 57 (BK) to the generic electronic module (GEM).
-------------------------------------------------------------------------------------
Safety Belt Warning When the ignition switch is turned to RUN or START from the OFF or ACC position and remains in RUN or START, the chime will sound for six seconds or until the safety belt is buckled. The safety belt warning indicator lamp (10C859) will turn on for 60 seconds, or until the LH front safety belt is fastened. Both the chime and lamp activate at the same time. If the safety belt is buckled when the ignition key is turned to RUN or START from OFF or ACC, the lamp will prove out for two seconds, but chime will not be activated. Any time the key is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Feb 25, 2009 | 1999 Ford Taurus

1 Answer

Removal of door ajar warning buzzer from 2002 Jetta


please check the fuse box yu can pull out the fuse which controls the buzzer and the interior light the easiest way to determine this fuse is to turn on the head light and start pulling thefuse out until it stops buzzing!!

Oct 16, 2008 | 2002 Volkswagen Jetta TDI

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...