Question about 2007 Hyundai Sonata3.3 SE

Open Question

How do I replace an alternator on a 2007 Sonata?

How do I remove the lower mounting bolt and also what is the best way to pull the alternator from the engine compartment?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 21 Answers

SOURCE: V6 2002 Hyundai Sonata - How to Remove Alternator?

It comes out through the bottom, lower the rear of the frame and remove the passenger half axle shaft to remove, sorry.

Posted on Jul 02, 2008

232K7
  • 26 Answers

SOURCE: Hyundai 2006 Sonata high mount brake light.

the rear seat does NOT have to be removed in order to replace the stoplamp and/or its bulb.
you have to get into the trunk, and there are (2) philips screws holding the stoplamp secured to the package tray. the actual process takes about 15 minutes, because to do it right you have to actually get IN the trunk.

the price they charged you sounds about right if the price of the stoplamp is included, dealerships tend to overcharge for parts.

Posted on Apr 14, 2009

  • 2 Answers

SOURCE: im replacing timing belt, accessory belts and water pump on my hyundai elantra gls 1997 sta wgn auto transmission. (1)Where is bolt to drain engine block coolant?(2)After removing front engine mountin

(1) No need to know if engine block coolant drain plug was available. Once the water pump was removed, all engine block coolant was drained. (2) After removing the three engine mounting bracket bolts, I also removed the mount bracket from the the body and made enough room to replace the timing belt easier.

Posted on May 20, 2009

ghost4548
  • 776 Answers

SOURCE: Need to know how best to remove the alternator of a 2000 sonata

Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Posted on Jun 28, 2009

ghost45
  • 1280 Answers

SOURCE: Locating and changing spark plugs on 2007 Hyundai Sonata 4 cylinder

They are directly below the coil packs (10mm bolts).


a73d0bb.jpg

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change alternator 2005 chryler 300


This answer covers:
2005 Chrysler 300 6cyl VIN "G" 3.5L SFI HO (72% of 2005 300's)
2005 Chrysler 300 6cyl VIN "R" 2.7L MFI DOHC (28% of 2005 300's)
2005 Dodge Magnum 5.7L engine

Alternator

Removal & Installation


WARNING - Precautions Section:
Disconnect negative cable from battery before removing battery output wire (b+ wire) from alternator. Failure to do so can result in injury or damage to electrical system.

2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Disconnect alternator field circuit plug.
  5. Remove B+ terminal nut and wire.
  6. Remove 2 lower mounting bolts.
  7. Remove alternator.
To install:
  1. Install alternator.
  2. Install upper bolt mounting bolt.
  3. Install 2 lower mounting bolts.
  4. Tighten bolts to 48 ft. lbs. (65 Nm).
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Connect alternator field circuit plug.
  7. Install alternator drive belt.
  8. Connect negative battery cable.
3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Remove bracket bolts.
  5. Remove upper mounting bolt.
  6. Raise and support vehicle.
  7. Remove middle splash pan.
  8. Disconnect alternator field circuit plug.
  9. Remove B+ terminal nut and wire.
  10. Remove lower mounting bolts.
  11. Remove alternator.
To install:
  1. Install alternator.
  2. Install lower mounting bolts. Loosen install the upper mounting bolt.
  3. Tighten lower mounting bolts to 48 ft. lbs. (65 Nm).
  4. Connect alternator field circuit plug.
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Install middle splash pan.
  7. Lower vehicle.
  8. Remove loose installed upper bolt.
  9. Install bracket and bracket bolt.
  10. Install upper mounting bolt and bracket.
  11. Tighten upper mounting bolt to 48 ft. lbs. (65 Nm).
  12. Tighten the bracket bolt to 40 ft. lbs. (54 Nm).
  13. Install alternator drive belt.
  14. Connect negative battery cable.
5.7L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable at battery.
  3. Remove alternator drive belt.
  4. Raise and support vehicle.
  5. Unsnap plastic insulator cap from B+ output terminal.
  6. Remove B+ terminal mounting nut at rear of alternator. Disconnect terminal from alternator.
  7. Disconnect field wire connector at rear of alternator by pushing on connector tab.
  8. Remove alternator support bracket nut and bolt. Remove support bracket. See Figure 1.
  9. Remove 2 alternator mounting bolts. See Figure 2.
  10. Remove alternator from vehicle.

Fig. 1 Alternator Support Bracket - 5.7L engine

7309257c-afe6-4c17-9422-d7fa2e3bd4b1.jpg

Fig. 2 Alternator Mounting Bolts - 5.7L engine

22b81ff7-7912-467f-9eaf-13ba2ff3a1a4.jpg

Oct 13, 2014 | 2005 Chrysler 300

1 Answer

Pulling out the alternator in a 2007 honda pilot


to remove alternator you have to remove intake manifold cover.and remove the ignition coil covers then remove alternator wiring harness connectors and remove alternator mounting bolts.

Dec 15, 2012 | 2007 Honda Pilot

3 Answers

Is it hard to replace alternator? I heard that you take right wheel off to get to it?


1. Disconnect and isolate negative battery cable at battery. 2. Remove the right front wheel. 3. Remove the underbody air dam.



4. Remove the accessory drive splash shield.



5. Remove the accessory drive idler pulley.



6. Loosen the lower mounting bolt.



7. Loosen the A/C compressor and relocate, pull down and to outboard side of vehicle to make room to remove generator.



8. Unplug field circuit from generator.



9. Remove the B+ terminal nut and wire.



10. Remove the upper mounting bolt. 11. Remove the generator lower mounting bolt.



12. Relocate the battery terminal (1) to the other side of the A/C line (2) for removal of the generator.



13. Rotate generator pulley down.



Dec 14, 2010 | 2008 Dodge Caliber

1 Answer

Trying to remove an alternator from an 06 altima


Removal and Installation L4-2.5L (QR25DE) Engines To Remove:
nis_alt_l4_alt.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Engine cover
    • Front/right-side engine undercover
    • Drive belt
    • Alternator harness connector
    • Engine ground wire from top mount
    • Alternator upper and lower mounting bolts
  3. Set the alternator aside and remove the top mount.
  4. Remove the alternator.
To Install:
nis_alt_l4_alt1.gif

  1. Slide alternator in place.
  2. Install or connect the following:
    • Alternator top mount
    • Alternator upper and lower mounting bolts
    • Engine ground wire from top mount
    • Alternator harness connector
    • Drive belt
    • Front/right-side engine undercover
    • Engine cover
    • Negative battery cable
V6-3.5L (VQ35) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain coolant from the radiator into a suitable container.
  4. Remove or disconnect the following:
    • Radiator
    • Front/right-side engine under cover
    • Drive belt
    • Idler pulley
    • Alternator adjustable top mount
    • Alternator lower mount bolt and nuts
    • Alternator lower front bracket bolt
    • Alternator harness connectors
    • Alternator
To Install:
nis_alt_chg_v6.gif

  1. Install or connect the following:
    • Alternator in place
    • Alternator harness connectors
    • Alternator lower front bracket bolt
    • Alternator lower mount bolt and nuts
    • Alternator adjustable top mount
    • Idler pulley
    • Drive belt
    • Front/right-side engine under cover
    • Radiator
  2. Replace the engine coolant.
  3. Connect the negative battery cable.
  4. Start the engine and check for leaks.
  5. Recheck coolant level and top off as needed.
prev.gif next.gif

Oct 15, 2010 | 2006 Nissan Altima

1 Answer

ALTERNATOR REPLACEMENT


Assuming this is a XG 350, the process is lengthly.
1. Remove the RH radiator cooling fan (two 10mm bolts at the top & wiring harness connector to it).
2. Lift vehicle to remove the Right Front wheel (then remove 4 10mm bolts securing the plastic splash shield & remove it)
3. Loosen the 14mm nut on the alternator belt tensioner pully
4. Loosen the tension on the belt by rotating (counter-clockwise) the 14mm bolt at the bottom of the idler pully and remove the belt.
5. remove the pully & the idler pully (three 12 mm bolts)
6. Loosen the 14mm nuts at the top and bottom mounting points of the alternator.
7. Using a floor jack (or vehicle lift), support the engine using a jack-stand & 2x4 piece of wood under the oil pan.
8. This is tricky - lift the engine 'SLIGHTLY' to take pressure off the front engine mount - loosen the 17 mm nut on top of the mount itself and observe engine movement. If the engine moves upward 'slightly' remove the 17mm nut - if not, raise the engine slight more until you see the mounting bracket rise off the mount.
9. Remove the remaining 17mm nut (deep well socket), and two 17mm bolts and remove the engine mount bracket.
10. Here's another tricky step. Some 350's bottom Alternator bolt bores are 'SLOTTED'... some are NOT. You'll need to determine wether you'll need to REMOVE the lower bolt, or just loosen the mounting sleeve at the bottom bolt. If it's 'sleeved', I use an air hammer to loosen the sleeve. If it's not slotted, I remove the lower bolt (it's the only way to remove the alternator and pry it off).
11. At the top is an "L" bracket which uses two 12mm bolts to attach it to the engine (head). One of the two 12mm bolts is difficult to get to -- do your best to remove it because the battery cable to the alternator is in the way.
12. Disconnect the alternator wiring (battery cable & regulator harness connector)
13. Lift the engine as high as it will go & pry the alternator off its lower mounting.
14. manuver the alternator upward taking care not to damage the radiator.
15. Installation is in reverse order.
NOTE: If your XG's lower mounting point was slotted, your task is easy. If it isn't, your task now becomes more difficult as you must align the new alternator to facillitate re-insertion of the lower bolt.
PS If not slotted, I use a telliscoping magnet to help re-insert the lower bolt.

Aug 09, 2010 | 2004 Hyundai XG350

1 Answer

How do I replace the alternator in a 2002 hyundai sonata GLS v6?


For 2002 Hyundai Sonata 2.7L MFI DOHC 6cyl check this procedure...
Alternator - Removal
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator

    0e1822c.jpg
    Fig. Exploded view of the alternator-XG 300
Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator
  3. Install or connect the following:
    Alternator and reposition the radiator, if raised Alternator wiring harness connectors Alternator drive belt
  4. Adjust the alternator belt and torque the bolts to the following specifications:
    1. Accent: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 14-20 ft. lbs. (19-28 Nm).
    2. 2.0L and 2.5L Sonata, Elantra and Tiburon: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 105-132 inch lbs. (12-15 Nm).
    3. 2.4L Sonata: Pivot bolt to 26-41 ft. lbs. (34-54 Nm) and the adjustment bolt to 14-18 ft. lbs. (19-25 Nm).
    4. 3.0L Sonata and XG 300: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 11-16 ft. lbs. (15-22 Nm).
  5. Install the radiator mounting bolts, if removed.
  6. Connect the negative battery cable.

Hope helps (remember rated this).

Jun 25, 2010 | Hyundai Motor 2002 Sonata

2 Answers

Replace 1997 civic ex alternator


The alternator is removed from the bottom of the vehicle. place the vehicle on jackstands positioned on the body, so the suspension hangs (you'll need this extra clearance to get the alternator past the axle shaft). 1). Disconnect the battery 2.) remove the upper mounting bolt (12mm) 3.) remove the terminal nut from the white wire. (10mm) 4.) Disconnect the 4pin connector 5.) From under the vehicle remove the lower mounting through bolt nut and through bolt (14mm) 6.) Remove the alternator from the lower mount and position the alternator to the side of the lower mount. 7.) remove the two lower mount bolts (14mm) and remove the lower mount asy. 8.) remove the alternator down the axle and out below the wheelwell. its going to be a tight fit so you'll have to turn the alternator at just the right position to get it out.

Jan 09, 2010 | 1997 Honda Civic

2 Answers

How do i install a alternator for a 07 dodge caliber sxt. what tools would i need to remove and install.


you will need to disconnect the negative battery cable at the battery, remove right front wheel, remove underbody air dam, remove accessory drive splash shield, remove the accessory drive idler pulley. Next loosen the lower mounting bolt, then loosen the a/c compressor and relocate(pull down and to the outboard side of the vehicle to make room for the alternator the come out) next uplug field circuit from alternator and the B+ terminal nut and wire. remove upper mounting bolt on the alternator and lower mounting bolt. relocate the terminal to the other side of the a/c line. Rotate alternator pulley down and slide down and out of vehicle. Yes, its a pain in the ****.

Oct 14, 2009 | 2007 Dodge Caliber SXT Sport Hatchback

3 Answers

How do I remove the alternator from a 2002 V6 Hyundai Sonata once I have disconnected the alternator?


Removal
  1. Remove or disconnect the following:

    Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator

0f18cd4.gif


Fig. Exploded view of the alternator-XG 300 and XG 350


Removal & Installation
  1. Remove or disconnect the following:
    Negative battery cable Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator 5ead6d5.gif


  2. Fig. Exploded view of the alternator-XG 300 and XG 350

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator

    27b2f58.gif

    Fig. Exploded view of the alternator-XG 300


    0900c15280196f8f.jpg
    Fig. Exploded view of the alternator-XG 350

  3. Install or connect the following:

    Alternator and reposition the radiator, if raised Alternator wiring harness connectors Alternator drive belt
  4. Adjust the alternator belt and torque the bolts to the following specifications:
    1. Accent: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 14-20 ft. lbs. (19-28 Nm).
    2. 2.0L and 2.5L Sonata, Elantra and Tiburon: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 105-132 inch lbs. (12-15 Nm).
    3. 2.4L Sonata: Pivot bolt to 26-41 ft. lbs. (34-54 Nm) and the adjustment bolt to 14-18 ft. lbs. (19-25 Nm).
    4. 3.0L Sonata and XG 300: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 11-16 ft. lbs. (15-22 Nm).
  5. Install the radiator mounting bolts, if removed.
  6. Connect the negative battery cable.


I hope hrlp you with this. Good luck and remember rated this help-


Aug 25, 2009 | Hyundai Sonata Cars & Trucks

1 Answer

Where is my alternator located at on my hyundai 2000 gls v6 and can a regular person do it or do i have to take it in to a shop


under the steering column.

Disconnect negative battery cable
Raise car
Disconnect the wire harness from the electrical connections
Loosen the lower mounting bolts. Working from top loosen the upper adjustment lockbolt, back off the adjustment bolt swivel alternator toward the engine and then release the drivebelt from the pulley
Unscrew and remove the upper and lower mounting bolts and washers then remove alternator from its mounting bracket

Jul 13, 2009 | 2001 Hyundai Sonata

Not finding what you are looking for?
2007 Hyundai Sonata3.3 SE Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...