Question about Cars & Trucks

1 Answer

I have a 06 crown Vic I changed transmission strainer my car drove for about a minute and stopped now it only go in reverse but not drive

Posted by on

Ad

1 Answer

You may have inadvertently over-tightened the valve body bolts (should be about 70-90 inch-pounds), OR you may have omitted the pickup tube gasket, causing the pickup tube to suck air.

Posted on Jun 11, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: 1996 Crown Vic, Valve noise under heavy acceleration

No use what's in there, but have the engine de-carboned by a Ford dealer, or remove the octane adjust shorting bar located near the ignition module (retards timing 2 degrees), this will in most cases cure the issue unless there is allot of carbon in the cylinders. There are also methods of ing this de-carbon procedure at home, check on the internet for tips.

PLEASE RATE THIS SOLUTION

Posted on Oct 22, 2008

  • 14036 Answers

SOURCE: 2001 crown vic keeps burning 30A PCM relay fuse

have fuel pump checked i have known a bad fuel pump shorting out causing pcm fuse to blow.

Posted on May 10, 2009

  • 33 Answers

SOURCE: Replace horn on 2006 crown vic

I believe once you have mounted the horn and connected the wire you will find that the horn wire was cut at (by) the steering coloum that the siren override was hooked to,you will have reconnect this,I hope this helps you

Posted on Jul 04, 2009

Murphybanton
  • 2004 Answers

SOURCE: 1991 735i automatic transmission,no forward drive, has reverse

The transmission has gone bad and all I can say is that you need to replace it.

Good luck.

Posted on Aug 29, 2009

  • 111 Answers

SOURCE: 06 crown vic stalls out when full throttle

put these codes directly one at a time on google search and you will find the result

Posted on Sep 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is wrong with the truck?


Sounds like your transmission is either out or close to it. I had a 2003 ford crown vic police interceptor with the same problem, mine was so bad that I had to floor the gasfor about 15 minutes driving around 3mph in circles till the transmission got warm, then bang it drove fine. Now this may not be it, so don't get your hopes up, just could be the problem like with me.

Jul 24, 2015 | 1999 Ford Explorer

1 Answer

2006 crown vic, What are the symptoms of bad transmission range sensor


not shifting --- slow shifting --- missing gear changes --- no OD or reverse or slow shifting to them. Have a pressure test done on the transmission to check for internal damage and have the bands and clutch packs adjusted . Run fault codes if this is available on your vehicle.

Jan 03, 2014 | 1997 Ford Crown Victoria

1 Answer

98 crown vic transmission slipping


Change the filter and fluid. This car if the transmission is original should have a torque converter drain. Drain the torque converter also,it gets almost all the fluid out of the transmission. Doing this the car will require almost 12 quarts of fluid. Worth a shot. I change mine at 25000 mile intervals.

Oct 31, 2012 | 1998 Ford Crown Victoria

1 Answer

'99 Ford Crown Vic LX: #12 30A Maxi fuse blows seconds after starting or ignition turned on.


i had this problem with my 1999 jeep grand cherokee laredo with the brake lights it kept popping fuses right after the ignition was turned on try putting a higher amp fuse in place of the old one that keeps blowing then check for shorts to the starter and check grounds and wires and also the transmission issue check the fluid and then if the fluid is fine change the transmission filter the filter may have not gotten replaced when the transmission was rebuilt and may be clogged or dirty

Oct 04, 2012 | 2002 Ford Crown Victoria

1 Answer

2000 Ford Crown Victoria transmission want shift into drive but have reverse


check pressures for drive gears if not in range then possable bad clutches in the ****** if you have a scan tool scan for shift coads and tern your shift sylinoids on and off to see if you have engagement if not rebuild or replace

Jul 22, 2012 | 2000 Ford Crown Victoria

1 Answer

I have 98 crown Vic it seam like the transmission is not changing gears what would be the problem.


check your fluid level, add fluid if nessary, or your filter is stopped up

Jan 03, 2012 | 1999 Ford Crown Victoria

6 Answers

I have a 2006 Ford Crown Vic Police Interceptor. I am having a problem with the dash. As I am driving it all the warning lights come on and the speedometer, tach, and odometer all stop working. I have...


Has anyone bothered to scan the IPC (Instrument Panel Cluster) or the GEM (General Electronic Module) to see if there are any fault codes? Does the engine run OK when this happens? I had a Grand Marquis that was doing something similar and the modules had several U-codes. Finally found the problem in the Transmission Range Sensor - it was shorting out the data line.

Dec 02, 2010 | 2006 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...