Question about Cars & Trucks

1 Answer

1999 plymouth breeze 2.0 motor how do I replace exhaust manifold

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,679 Answers

Very straight forward ,there may be a few pipes, wire etc to move out of they way, so make sure you know where every thing goes back if you do have to remove anything , take a photo as you go along for referance , also would be worth getting a workshop manual as will give step by step guide, there are a series of nuts along the exhaust manifold that bolt onto the head , these will be very tight so a long knuckle bar will be required to loosen them off , don't remove one at a time , undo them a little at a time , there will be a clamp that connects the manifold to the exhaust pipe , these are bolted together as well , once the nuts are remove the manifold can be removed , it may require a bit of a tap with a hammer with a piece of wood placed on the manifold , don't hit the manifold directly , clean of the gasket on the head and manifold , refit is just the reverse with a new gasket , there is uasually a cone shaped ring that seals the manifold to the exhaust pipe make sure this is central when refitting or will get a leak good luck

Posted on Jun 18, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: How to change the serpentine belt on '98 Plymouth Breeze?

All you need is a long prubar (or you can rent a tensioner wrench at the parts store) essentially a open end wrench with a 3 ft handle.
Put the tensioner wrench on the nub of the tensioner and pull back... this will release the tension on the old belt. Remove it from one of the pulleys, and then from the entire system.
Note how it is routed through the pulleys, and put the new one on the same way.
The car should have a sticker on the radiator support telling you the path of the belt.

Posted on Jan 08, 2009

  • 54 Answers

SOURCE: How do you remove the starter from a 1999 Plymouth

On a 2.0 unhook the wires from the back of the starter then there are 2 bolts that go through the nose cone of the starter into the block, you remove those 2 bolts and the starter will fall out.

Posted on Jun 16, 2009

  • 1071 Answers

SOURCE: My 1999 Plymouth Breeze has the horn on all the

it is in the clock spring behind steering wheel contacts are broke completing circuit and making horn work

Posted on Jul 21, 2009

  • 603 Answers

SOURCE: oil leak in a 98 plymouth breeze 2.0

I've had a 1990 Acclaim, a 1990 Shadow, and a 1998 Breeze, all have a head gasket leak. The Breeze was the only one to have oil leak and it was on the rear of the engine. I'd guess that's your problem.

Posted on Jan 11, 2010

  • 67 Answers

SOURCE: 1999 plymouth voyager blower motor

you have to replace it its located on the passenger side under the dash

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1999 Plymouth Breeze when idle the Gage Norma when driving the 2 miles an hour at 60 miles an hour temperature gauge indicates on the low level way to cold my heater in the car gets cool? Why


Hello your problem is simple if it is just sitting there running and you have heat but if you drive it and you lose heat it is the thermostat, it is stuck open and the fluid is passing threw the motor to fast to heat up. get a new thermostat and problem will be fixed
List Search 1999 Plymouth Breeze Reilly Auto Parts

Dec 04, 2016 | 1999 Plymouth Breeze

1 Answer

Why a rattle in F/E on D/S ?


Heat shield on manifold, manifold, Exhaust system loose, bad motor mounts.

Aug 02, 2014 | 1999 Plymouth Breeze

1 Answer

How to remove exhaust manifold on 1999 plymouth breeze


which engine?
NO MATTER,
remove all bolts and bam, i's off.
only rust makes it hard, ever do rusty bolts?

May 14, 2014 | Cars & Trucks

1 Answer

How do I replace exhaust manifold on 2.0L 1999 plymouth breeze


you need to take the expnsion chamber off..(drop exhaust from engine back) next drill out old manifold bolts (be careful) you will need new bolts and a tap and dye set to rethread wholes possibly before connecting new manifold make sure engine is COLD. expans chamber is where pipes of exhaust connect to manifold,kind of a junction like. If you have aluminuim heads you will need a HIGH speed drill and will take a good deal of time and possibly a few nw bits to get old bolts out all the way. good luck hope this helps you out.

May 14, 2014 | Cars & Trucks

1 Answer

1998 plymoth breeze, egr location and any tricks to replacing it


on back side of engine on exhaust manifold ... and a easy clip 2 remove ... but egr might be rusted .. so easy way is to take off exhaust all the way and tap with hammer and muscle it out ... but dont do not break it .

Jan 19, 2010 | 1998 Plymouth Breeze

3 Answers

I need to replace the oil pressure switch in a 98 Plymouth breeze. Can you help me?


yes its easy to locate because its green in colour its located on the back side of the engine under the air filter casing and the exhaust manifold its best got at from under the car hope that helps

Nov 19, 2009 | 1998 Plymouth Breeze

1 Answer

Where is oil sending unit located for 98 plymouth breeze


In the block on the right side (rear side near firewall) close to the transmission under the exhaust manifold.

May 18, 2009 | 1998 Plymouth Breeze

1 Answer

Egr valve


well nanifold is part of the emission and the egr repair both and save time re e testing it! you want it to go through first time with the above wrong it wont pass!!

Jan 04, 2009 | 1998 Plymouth Breeze

1 Answer

How to adjust timing on a 1999 plymouth breeze 2.4 litre


the gears have indicators i and e on opp sides. the i is intake e is exhaust. the i should face away from the valve cover on the side the intake cam is on. this is the side of the head the intake manifold is on. the e should face away from the valve cover on the side the exhaust manifold is on. the e gear will be a slight bit lower than the i gear. almost straight across from each other. good luck

Jul 31, 2008 | 1999 Plymouth Breeze

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...